JWA FULLER 74631 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
4 DRAWER TALL CHEST
FULLER
ITEM CODE 74631
800mm
450mm
mm0011

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when ling. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instrucons carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over ghten the screws and bolts as this may damage the threads
Allow 30 min For 1 person Addional tools required
2

PARTS LIST
3
7
8
1
4
6
3
3
17
17
X4
X4
5
12
16
13
10
11
9
14
14
15
15
2
3
3
18
18
18

4
NO. ITEM QTY QTY NO. ITEM
A
B
C
D
E
F
G
I
J
L
H
NO. ITEM QTY NO. ITEM QTY
11 PC
3
1 PC
41 PC
51 PC
61 PC
4 PCS
7
4 PCS
4 PCS
4 PCS
4 PCS
Φ6*35
Φ15*10
Φ8*30
Φ4*50
Φ6*60
Φ3*12
Φ4*20
Φ4*35
8
4 PCS
10
11
12
13
14
15
9
4 PCS
2 PCS
2 PCS
PARTS LIST
2
DR
CL
CR
DL
8PCS
8PCS
46PCS
46PCS
30PCS
12PCS
48PCS
2PCS
M
N
16PCS
20PCS
8PCS
1PC
4PCS
8PCS
4PCS
4PCS
4PCS
TOP PANEL
BOTTOM PANEL
LEFT SIDE PANEL
RIGHT SIDE PANEL
SIDE ARC PANEL
BACK PANEL
4 PCS
LEGS TRIANGLE
MIDDLE SUPPORT
DRAWER FRONT
DRAWER LEFT
PANEL
PANEL
PANEL
PANEL
PANEL
PANEL
PANEL
MIDDLE SUPPORT
PANEL
MIDDLE SUPPORT
PANEL
LEG
DRAWER RIGHT
DRAWER BACK
DRAWER BOTTOM
16 4 PCS
3 PCS
PANEL
LEGS SUPPORT
PANEL
LEGS SUPPORT
17
18
2 PCS

STEP 1:
STEP 2:
5
24xI 4xCL 4xCR
CL
CL
CL
CL
CR
CR
CR
CR
5
5
A
A
A
A
A
A
6xA

STEP 3:
STEP 4:
6
A
A
X4
A
A
3
16xA
6xB 6xC
4
5
18
18
18
C
C
C
C
C
C

STEP 5:
STEP 6:
7
C
C
C
B
B
B
BC
1
3
3
O
O
C
C
C
B
B
B
BC
2
3
3
8xB 8xC 2xO
4xA
4xB 4xC
C
C
C
C
B
B
B
B
1
4
5

STEP 7:
STEP 8:
8
5
2
5
4
6
6xB 4xC
2xB
17
17

STEP 9:
STEP 10:
9
8xC
12xD
14
14
15
15 D
DD
D
D
D
DD
D
D
D
D
5
4
2
14
14
15
15
C
C
CC
C
C
CC
5
4

STEP
STEP 12:
11:
10
16xM
8xG 1xH8xF8xE
2
7
7
7
7
2
8
8
8
8
EFG
H
EFG
E FG
H

STEP 13:
STEP 14:
11
L
L
L
L
L
L
LL
L
L
4xL
WALL
2xJ
J
J
J
J
J

12
STEP 15:
16:STEP
9
X4X4
X4 X4
20xN
20xB20xA

ASSEMBLY IS COMPLETE
13
STEP 17:
STEP 18:
DR
DL X4
4xDR4xDL24xI
9
9
9
9
Always Lift Your 4 Drawer Tall Chest When
Moving /Relocating - Do Not Drag.
Dragging Can Cause The Legs
To Bend/Break.

14
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1WALL FIXING X1 Expanded plastic pipe X1
HARDWARE

To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
15