JWA OLDHAM 69484 User manual

1
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
OLDHAM
ITEM CODE 69484
2 DRAWERS UNIT

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose aclean, level, spacious assembly area.Avoid hard surfaces that may damage the
product
2.Take care when lifting.Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2
Allow 45 min For 2person Additional tools required

PARTS LIST
1Top panel
2Bottom panel
3Left side panel
4Right side panel
5Back panel-bottom
6Drawer front panel
7Drawer left side panel
8Drawer right side panel
9Drawer back panel
10 Drawer bottom panel
11 Top panel
12 Back panel-top
Q1 Metal frame
Q2 Connection pipe
Q3 Coat hanger
3

4

Load fitting P into the bottom of metal frame Q1.
STEP 1:
Press the plastic clasp in the fitting E2 and disassemble E1
and E2.
STEP 2:
5

Use fitting F to fix E1 on the orifice position of panel 3 and
panel 4 respectively.
STEP 3:
Install Panel 12 on the Pane 11 with fitting D.
STEP 4:
6

Install Connection pipe Q2 to the Metal frame Q1 with fitting C,
and sssemble the componont of step 4 to the metal frame Q1;
Then install Q3 with the metal frame Q1 with fitting B.
aTEP 5:
Assemble Panel 2, 3 and 4 with fitting K and A, and after insert
the pabel 5, assemble the Panel 1 to Panel 3 and 4 with fitting
and K.
STEP 6:
7

Install the fitting O to the panel 6 with fitting J; And assemble
Panel 7,8 and 9 with fitting D, after insert the Panel 10,
assemble the panel 6 with fitting A.
STEP 7:
Install E2 to the drawer components with fiitting F, then
insert the the drawers into the cabinet.
STEP 8:
8

Install the fitting M to the panel 11 with fitting G, and Punch
holes in the wall at the appropriate position and insert the glue
N, lock screw I through M to the wall.
STEP 9:
9
ASSEMBLY IS COMPLETE

SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
10

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
• Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
11