JWA FROST 73667 User manual

1
ASSEMBLY INSTRUCTION
ITEM CODE 73667
FROST BUFFET
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt

2
PRE-ASSEMBLY PREPARATION
Allow 40 min
For 2 person Additional tools required
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when lifting. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instructions for future reference.

A
x 24
B
Φ15X12mm x 24
C
x 20
D
x 20
E
x 12
F
x 107
G
x 8
H
x 1
I
x 8
J
x 6
K
x 4
L
x 12
M
x 8
N
x 2
O
x 2
P
x 5
Q
x 5
R
x 2
Φ6X44mm Φ20X0.5mm Φ8X30mm
Φ3.5X14mm
14X14X9mm Φ55X18mm 4#
340mm7X50mm Φ35mm Φ4X35mm
Φ29X12mmΦ5X18mm Φ4X60mm 83X14X19mm
Φ8X38mmΦ16X2/3X12mm
1TOP PANEL
2BOTTOM PANEL
3SIDE PANEL
4SIDE PANEL
5 MIDDLE PANEL
6 MIDDLE PANEL
7MIDDLE CONNECTING PANEL
8BACK PANEL
9BACK PANEL
10 SHELF
11 DOOR
12 DOOR
13 DRAWER FRONT
14 DRAWER SIDE PANEL
15 DRAWER SIDE PANEL
16 DRAWER BACK PANEL
17 DRAWER BASE
PARTS LIST
1
2
3
5
6
4
13
14
15
16
17
13
14
15
16
17
13
14
15
16
17
7 x2
8
9
8
10
10
11
12
3

4
56
J1
J2
J1
J1
J1
J1
J1
J1
F
F
F
F
F
F
F
F
F
F
F
F
A
A
AA
A
J1
F
F
F
7
X2
5
6
P1
P2F
P2
P1
P2
FF
P2
P1
STEP 1:
• Prepare a floor or benchtop with a protective
blanket or carboard.
• Fix runners (J1)to panels (5)(6) with screws (F).
• Fix cam pin (A) to panels (5)(6).
STEP 2:
• Fix pusher base (P2)to panels (5)(6)(7) with screws (F).
• Fix the pusher (P1) to pusher base (P2).

A
A
A
A
A
A
A
A
DD
DD
DD
D
D
1
A
5
5
6
7
B
B
B
B
B
D
D
D
D
100%
STEP 3:
• Attach panel (5)(6) to panel(7) with dowel(D) and cam lock (B)
STEP 4:
• Fix cam pin (A) and dowel(D) to panel (1).

6
8
8
9
B
C
B
C
B
C
B
C
BC
BC
1
3
4
6
B
100%
C
STEP 5:
• Attach panel (3)(4)(5)(6) to panel (1) with cam lock (B)
and Hole cover (C)
STEP 6:
• Push the back panels (8)(9) in the body.
5

7
2
I
I
I
I
I
I
II
D
D
DD
DD
DD
2
H
I
F
P1
P2
F
P2
P1
STEP 7:
• Fix pusher base (P2)to panel (2) with screws (F).
• Fix the pusher (P1) to pusher base (P2).
STEP 8:
• Attach panel (2) to the body with dowel(D)and screws (I).
• Fasten with Allen Key(H)

8
10
10
M
M
G
x8
x8
x8
G-1
G-2
G-2
F
F
10
10
G-1
STEP 9:
• Fix adjusting foot (G-1) to panel(2) with screws (F).
• Fix adjusting foot (G-2) to adjusting foot (G-1).
STEP 10:
• Fix movable nail (M) to the body .
• Put panels (10) on the pin (M).
2

9
J2
FF
AA
AA
Q1
Q2
13 x3
A
F
E
N
N
O
R
8
F
E
E
F
EF
E
F
F
E
E
F
EF
E
F
F
E
E
F
EF
E
F
N
8
8
14 x3 15 x3
F
F
J2
F
F
J2
F
STEP 11:
• Attach back panel to the body with screws (F) and plastic buckle (E) .
• SAFETY BRACKETS INSTRUCTIONS See page 13
STEP 12:
• Fix runners (J2) to drawer side panels (14)(15) with screws (F).
• Fix metal plate (Q1) to panels (13) with screws (Q2).
• Fix cam pin (A) to panels (13).

10
17
C
16
14
15
L
L
LL
L
x3
CB
CB
BC
C
B
100%
13
x3
STEP 13:
• Attach panels (14)(15) to panel (16) with screw(L).
• Insert drawer base (17) as shown.
• Attach drawer front to the body with cam lock parts.
STEP 14:
• Assemble drawers to the body.