JWA RAINEY 68330 User manual

INSERT PAGE NUMBER
Importedby JWA Furniture Pty Ltd,Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
RAINEY
68330
Navy Queen Bed

Allow 45 min For 2 person Additional tools
required
1
PRE-ASSEMBLYPREPARATION
Before you start:
1. Choosea clean, level, spacious assembly area. Avoid hard surfaces thatmay
damagethe product
2. Take carewhen lifting. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damagethe threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from theproduct dueto possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instructions for futurereference.

2
7
3
1
54
5
7
7
7
6
2
A
M8X19 X16
B
M5X100 X1
C
M12 X1
D
M12 X4
E
M4X30 X6
F
M8X40 X4
G
M8X30 X12
H
M8 X8
1
Headboard
1
2
Side
Rails 2
3
Footboard
1
4
Cent
re rail 1
5
Support
legs 2
6
Slat
s1
7Feet 4
8
PARTS LIST
2

•Prepare a floor with a blanket or cardboard.
•Lay the Headboard(1) down in its back.
•Thread a bolt(G) through Spring washer(H) and
Washer(A). Do this for All 12 Bolts(G).
•Attach 2 x Feet(7), as shown below. With 2 x bolt(G) sets
per feet.
•Fasten with Allen Key(B)
STEP1:
3

•Repeat Step 1, but this time for the Footboard(3)
STEP2:
4

5
•Unscrew the bolts in the Headboard(1) and
Footboard(3), so they are half way out, with Allen Key(B)
•Have a 2nd person hold the headboard.
•Attach the one of the Side Rails(2) to the Headboard(1),
by clipping the bracket onto the bolts. Place the tongs of
the brackets in-between the washer and headboard.
•Now attach the other end of the Side Rails(2) to the
Footboard(3), by clipping the bracket onto the bolts.
Place the tongs of the brackets in-between the washer
and Footboard.
•Repeat for the other Side Rail.
•Do not tighten the bolts for now.
STEP3:

6
STEP4:
•Attach the Centre Rail(4) to the Headboard(1) and
Footboard(3), as shown below.
•Use 4x Bolts(G) paired with Washer(A). Fasten with Allen
Key(B).
4
STEP5:
•Now go around and tighten all the bolts from step 3. Use
Allen Key(B)

7
•Attach the 2 x support legs(5) to the Centre Rail(4). As
shown below.
•Thread Bolt(F) Through Washer(A). Then push the bolt
through the holes on the Centre Rail and Support Leg.
Screw on Nut(D) on the bottom onto Bolt(F). Tighten
bolt(F) with Allen Key(B), whilst holding nut(D) in-place
with Wrench(C).
•Repeat for the other support leg
STEP6:

•Place the slats(6) into the bed, as shown below.
•Secure the ends of the slats to the side rails with screw
(E) and a Philips head screw driver.
STEP8:
ASSEMBLY IS COMPLETE
8

REGULAR CARE:
•Protect from directsunlight
•Vacuum regularly using low suction
•Rotate reversible cushions regularly
CLEANING:
•Donot removecushion covers for separate cleaning even though they
may have zippers
•Donot wash, Do not dry clean, Donot shampooclean
•Clean with hot water extraction machine. Professional cleaning
recommended
•Do not use dishwashing liquid or laundry detergent
•Use only upholstery detergents
•Do not wet filling
•Dry in shade away from direct heat andsunlight
•Allow to dry thoroughly beforere-use
SPOT CLEANING:
•Do not rub
•Do not spot clean with anysolvent
•Treat spills and stains as soon aspossible
•Gently scrapeoffany soil or mop any liquid from the surface of the fabric
•Applyproprietary cleaning agents strictly according to instructions to
remove the residue of the spill
•Donot saturate the fabric or interior with water or other cleaning liquids
WARNING:
Applyonly water-based soil resist (fabric protection) treatments. Do not
use aerosol products
* PILLINGISNOTAFABRIC DEFECTORFAULTAND ISNOT
COVERED BYWARRANTY
* PILLING IS A NORMAL OCCURRENCE CAUSED BY WEAR AND TEAR AND DOES
NOT AFFECT THE DURABILITY ORFUNCTIONALITY OF THE FABRIC AND ISEASILY
REMOVED
9