JWA ENNA 73025 User manual

Imported by JWA FurniturePty Ltd, Qld, Brisbane Australia.
For anyassistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
73025
ENTERTAINMENT UNIT
ENNA
ITEM CODE
1200MM
500MM
340MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when ling. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all requiredcontents for complete assembly
4.Always read the assembly instrucons carefully before beginningassembly.
5.Keep all hardware partsand packaging out of reach of small children.
6.Do not over ghten the screws and bolts as this may damage the threads
Allow 30 min For 1 person Addionaltools required
2

PARTS LIST
3
1
2
34
5
6
7
8
9
10
11
11
11
11

PARTS LIST
4
NO. ITEM QTY NO. ITEM QTY
A8PCS
B8PCS
C20PCS
D16PCS
E24PCS
F8PCS
G2PCS
4PCS
I
2PCS
L
2PCS
M
4PCS
N
4PCS
O
2PCS
P
1PC
G
H2PCS
J
Φ4*12
Φ3*12
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PCE
2RIGHT MIDDLE PANEL
3LEFT MIDDLE PANEL
1 PCE
1 PCE
4SHELF PANEL 1 PCE
5LEFT SIDE PANEL 1 PCE
6RIGHT SIDE PANEL 1 PCE
7
LEG
1 PCE
81 PCE
91 PCE
10 1 PCE
11 4 PCE
Φ4*35
Φ4*20 Φ3*10
BACK PANEL
LEFT DOOR PANEL
RIGHT DOOR PANEL
BOTTOM PANEL

STEP 1:
STEP 2:
5
B
B
B
B
1
B
B
B
B
B X8
E
E
E
E
E
E
E
E
E X8

STEP 3:
STEP 4:
6
B
B
EEEE
A
AA
A
4
23
1
E X4A X4
B
EE
E
A
AE
A
A
4
23
1
65
E X4A X4

STEP 5:
STEP 6:
7
7
5
4
6
2
1
3
D
DD
D
1
4
23
65
7
D
DL
LL
D X4L X2

STEP 7:
STEP 8:
8
P X2N X4
D
D
D
DM
P
D
D
D
D
M
P
N
N
G
H
G
H
898
9
M X2H X2G X2D X8
1
4
23
65
7
8
9

STEP 9:
STEP 10:
9
F X8E X8
E
EE
E
F
F
F
F
E
E
F
E
E
1
4
23
65
7
8
9
10
F
F
F
I
C
C
C
CC
C
C
C
CC
II
I
CC
C
C
C
CC
C
C
C
I
CC
C
C
C
1
4
23
658
9
10
I X4C X20

STEP 11:
STEP 12:
10
O X4D X4
I
1
4
23
658
9
10
11
11 11 11
11
ODO
O
O
O
O

STEP 11:
STEP 12:
11
J
J X1
J
J
J
J
J
4
10
1
2
3
89

ASSEMBLY IS COMPLETE
12

13
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
14