JWA EDGAR 68430 User manual

1
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
EDGAR
ITEM CODE 68430
1 DRAWER DESK

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lifting. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instructions carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over tighten the screws and bolts as this may damage the threads
2
Allow 45 min For 2 person Additional tools required

3
PARTS LIST
1Desktop panel
2Left side panel
3Right side panel
4Back panel
5Drawer panel
6Drawer left side panel
7Drawer right side panel
8Drawer middle panel
9Drawer back panel
10 Drawer bottom panel
P1 Metal panel
P2 Support pipe

4

Load the fitting H into the metal frame P1.
5
STEP 1:
Press the plastic part on the E2 and separate E1 and E2.
STEP 2:

The disconnected part E1 corresponds to the lead hole on
panel 2 and 3 respectively, and is locked and fixed with part F;
Pay attention to distinguish the opening direction of E1 parts.
STEP 3:
Connect and lock the assembled panel 2, 3and 4 with fitting G.
STEP4:
6

Fix the metal pipe P2 on panel 1 with fitting B.
STEP 5:
Connect and fix panel 1 and panel 4 with fitting A and D.
STEP 6:
7

Fix the metal frame P1 in the assembled panel assembly with
fitting G.
STEP 7:
1) Fix panel 6 and panel 7 on panel 9 with fitting G;
2) Load panel 10 into the corresponding slot of panel 6,7 and 9;
3) Connect panel 8 to panel 9 with fitting A;
4) Connect and fix panel 5 with panel 6,7 and 8 with fitting A.
STEP 8:
8

Fix E2 on panel 6 and panel 7 with fitting F.
STEP 9:
Put the assembled drawers into the corresponding position
of the desk.
STEP 10:
9

10
Install a fall preventer.
STEP 11:

11
ASSEMBLY IS COMPLETE

12
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.

13
To protect your furniture, we suggest the following:
•Avoid placing your furniture in direct sunlight.
•Do not place furniture directly under windows.
•Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
•Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
•Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void