Kärcher K 3.450 User manual

English 2
Français 18
Español 35
59637980 05/10
K 3.450
HIGH PRESSURE WASHER - OPERATOR MANUAL
NETTOYEUR HAUTE PRESSION - MANUEL D'UTILISATION
MANUAL DE USUARIO DEL LIMPIADOR DE ALTA PRESIÓN

2 English
DANGER
indicates “an imminently hazardous sit-
uationwhich,ifnotavoided,willresultin
death or serious injury.”
WARNING
indicates “a potentially hazardous situa-
tion which, if not avoided, could result in
death or injury.”
CAUTION
indicates “a potentially hazardous situa-
tion which, if not avoided, may result in
minor or moderate injury or in property
damage incidents.”
For household use only!
The owner and/or user must have an
understanding of the manufacturer’s
operating instructions and warnings be-
fore using this pressure washer.
Warning information should be empha-
sized and understood.
If the operator is not fluent in English,
the manufacturer’s instructions and
warningsshallbereadtoanddiscussed
withtheoperatorintheoperator’snative
language by the purchaser/owner, mak-
ing sure that the operator comprehends
its contents.
Owner and/or user must study and
maintain for future reference the manu-
facturers’ instructions.
In the U.S. or Canada, please call
1-800-537-4129 for warranty issues
and visit www.karcher-help.com for
technical support and product assis-
tance.
Please take a moment to register your
pressure washer online at
www.karcher-register.com. Be sure
to save your purchase receipt, it will be
required for repairs covered by warran-
ty.
Call: 01-800-024-13-13 for help or visit
our website: www.karcher.com.mx
HIGH PRESSURE WASHER OPERATOR MANUAL
Model Overview 3
Important Safety Instructions 4
Assembly Instructions 6
Operating Instructions 6
Using the Accessories 8
Working with Detergents 8
Taking a Break 9
Shutting Down & Clean-Up 10
Winterizing and Long-Term Storage 11
Maintenance Instructions 11
Cleaning Tips 12
Optional Cleaning Accessories 14
Troubleshooting 16
Safety Alert Symbols
Specifications
Max. Pressure 2000 PSI
Max. Water Flow 1.4 GPM
Amp draw 13 AMPS
Voltage 120 V
Part No. 1.601-776.0
Serial no.
Owner/User Responsibility
Customer Support
USA and Canada
Customer Support
Mexico

English 3
1 Water inlet with garden hose con-
nector
2 High pressure outlet
3 ON/OFF switch
4 Detergent tank (removeable)
5 Storage for trigger gun
6 Transport handle
7 Accessory storage
8 PowercordwithGroundFaultCircuit
Interrupter (GFCI)
9 Wheels
10 Trigger gun
11 Trigger gun safety lock
12 Key to detach the high-pressure
hose from the trigger gun
13 High pressure hose
14 Dirtblaster®(Rotary spray wand)
15 Vario Power Spray wand
16 Wash brush
MODEL OVERVIEW

4 English
WARNING
When using this product basic precau-
tions should always be followed, includ-
ing the following:
To reduce the risk of injury, close su-
pervision is necessary when a prod-
uct is used near children.
Know how to stop the product and
bleed pressures quickly. Be thor-
oughly familiar with the controls.
Stay alert – watch what you are do-
ing.
Do not operate the product when fa-
tigued or under the influence of alco-
hol or drugs.
Keep operating area clear of all per-
sons.
Do not overreach or stand on unsta-
ble support. Keep good footing and
balance at all times.
Follow the maintenance instructions
specified in the manual.
This product is provided with a
Ground Fault Circuit Interrupter built
into the power cord plug. If replace-
ment of the plug or cord is needed,
use only identical replacement parts.
WARNING
Risk of Injection or Injury – Do Not
Direct Discharge Stream At Per-
sons.
Highpressurejetscanbedangerous
if misused. The jet must not be di-
rectedatpersons,animals,electrical
devices, or the unit itself.
Wear safety goggles.
WARNING
Risk Of Explosion – Do not spray
flammable liquids.
Do not use acids, alkaline, solvents,
or any flammable material in this
product. These products can cause
physical injuries to the operator and
irreversible damage to the machine.
CAUTION
Gun Kicks Back – Hold with both
hands.
The Trigger Gun Safety Lock pre-
vents the trigger from accidentally
being engaged. This safety feature
DOES NOT lock trigger in the ON
position.
WARNING – Risk of Electrocution
Inspect cord before using – Do not
use if cord is damaged.
Keep all connections dry and off the
ground.
Do not touch plug with wet hands.
Do not use extension cord with this
product.
Connect to individual branch circuit
only.
CAUTION
Thisunithasbeendesignedforusewith
cleaning detergents recommended by
the manufacturer. The use of other
cleaning detergents may affect the op-
eration of the machine and void the war-
ranty.
WARNING
Do not spray electrical apparatus and
wiring.
Do not use with flammable liquids and
toxic chemicals.
Injection hazard: equipment can cause
serious injury if the spray penetrates the
IMPORTANT SAFETY INSTRUCTIONS

English 5
skin. do not point the gun at anyone or
any part of the body. In case of penetra-
tion seek medical aid immediately.
This system is capable of producing
13800 kPa /2000 PSI to avoid rupture
and injury, do not operate this pump
with components rated less than
13800 kPa /2000 PSI working pressure
(including but not limited to spray guns,
hose and hose connections).
Before servicing, cleaning or removing
any parts, shut off power and relieve
pressure.
This product must be grounded. If it
should malfunction or breakdown,
grounding provides a path of least resis-
tance for electric current to reduce the
risk of electric shock. This product is
equipped with a cord having an equip-
ment-grounding conductor and a
grounding plug. The plug must be
pluggedintoanappropriateoutletthatis
properly installed and grounded in ac-
cordance with all local codes and ordi-
nances.
DANGER
Improper connection of the equipment-
grounding conductor can result in a risk
of electrocution. Check with a qualified
electrician or service personnel if you
are in doubt as to whether the outlet is
properly grounded. Do not modify the
plug provided with the product - if it will
not fit the outlet, have a proper outlet in-
stalled by a qualified electrician. Do not
use any type of adapter with this prod-
uct.
This pressure washer is provided with a
ground-fault circuit-interrupter (GFCI)
built into the plug of the power-supply
cord. This device provides additional
protection from the risk of electric
shock. Should replacement of the plug
or cord become necessary, use only
identical replacement parts that include
GFCI protection.
CAUTION
When connecting the water inlet to the wa-
ter supply mains, local regulations of your
water company must be observed. In some
areas the unit must not be connected di-
rectly to the public drinking water supply.
This is to ensure that there is no feedback
of chemicals into the water supply. Direct
connection via a receiver tank or backflow
preventer, for example, is permitted.
Dirt in the feed water will damage the
unit. To avoid this risk, we recommend
fitting a water filter.
Garden hose must be at least 1/2
inch or 5/8 inch in diameter.
Flow rate of water supply must not
fall below 2 GPM (gallons per
minute).
Flow rate can be determined by run-
ning the water for one minute into an
empty 5-gallon container.
The water supply temperature must
not exceed 104°F/40°C.
Never use the pressure washer to
draw in water contaminated with sol-
vents, e.g. paint thinners, gasoline,
oil, etc.
Always prevent debris from being
drawn into the unit by using a clean
water source.
GROUNDING INSTRUCTIONS
GROUND FAULT CIRCUIT IN-
TERRUPTER PROTECTION
WATER SUPPLY
(Cold Water Only)

6 English
APhilips Screwdriver, medium size
(not supplied)
for final assembly
STEP 1:
STEP 2:
STEP 3:
STEP 4:
STEP 5:
STEP 1:
Insert the spray wand of your choice
into the trigger gun. Press in against
the spring tension and twist into
locked position.
STEP 2:
Connect garden hose to unit’s water
inlet.
ASSEMBLY INSTRUCTIONS
Required tools
Assembly
OPERATING INSTRUCTIONS

English 7
STEP 3:
STEP 4:
Connect garden hose to the cold wa-
ter source and turn water on com-
pletely.
STEP 5:
Plug the Ground Fault Circuit Inter-
rupter (GFCI) into a receptacle.
Press RESET button, indicator
should be “ON”.
Press TEST button, indicator should
be “OFF”.
Press RESET button for use.
We recommend that you test the GFCI
as part of your startup procedure each
time you use your pressure washer. To
learnhowtopeformthistestonyourunit,
visit http://www.karcherresidential.com/
gfci_test.php for detailed instructions for
your type of GFCI.
WARNING
Do not use if above test fails.
STEP 6:
Unlock the trigger gun safety lock.
Trigger the gun to eliminate trapped
air, wait for a steady flow of water to
emerge from the spray nozzle.
STEP 7:
Turn on the high pressure washer (I/
ON).
Themotorstarts onlyif thetrigger
of the gun is pulled and shuts off
when the trigger is released.
Note:
This pressure washer has been tested
by Kärcher’s quality assurance team. A
small amount of water may be present
inthewaterinletoroutlet.Thisisnormal
and will not affect the performance of
the pressure washer.

8 English
WARNING
To avoid serious injury never point
spray nozzle at yourself, other per-
sons or animals.
Always test an inconspicuous area
before cleaning with high pressure.
The Vario Power Spray Wand allows
you to adjust the cleaning pressure.
To clean at maximum pressure, the
wand must be positioned to the high
pressure setting (Max).
For lower pressure turn the wand
collar in the minus (Min) direction.
To apply detergent, the wand must
be positioned to the lower pressure
setting (Mix).
This nozzle features a 0º pencil jet
which rotates 360º for maximum dirt
cutting action, effectively increasing
cleaning performance up to 50%.
This nozzle combines the cleaning
performance of a 0º pencil jet with
thesurfacecoverageofawideangle
nozzle.
Not recommended for soft materi-
als, siding, painted surfaces,
decks or autos.
Always test an inconspicuous area
before cleaning with the Dirtblaster®.
Detergents can only be applied at
low pressure setting (Mix).
STEP 1:
Install the Vario Power Spray Wand.
Set the spray wand to the low pres-
sure setting (Mix).
STEP 2:
Fill the Detergent Tank with the se-
lected detergent.
USING THE ACCESSORIES
Vario Power Spray Wand
Dirtblaster®
WORKING WITH DETERGENTS

English 9
STEP 3:
Turn on the pressure washer (I). Pull
trigger to operate unit. Liquid deter-
gentis drawninto the unit and mixed
with water. Apply detergent to work
area. Do not allow detergent to dry
on surface.
STEP 4:
To rinse, move the VPS out of „Mix“
position and pull trigger to operate
unit.
STEP 5:
Cleaning up: Always draw fresh wa-
ter through the detergent tank or si-
phon tube when done to flush any
remaining detergents from the injec-
tion system.
For best results see Cleaning Tips
for specific information on how to
clean different surfaces.
Always Use Kärcher®Detergent for
Best Results
Kärcher®biodegradable detergents are
specially formulated to protect the envi-
ronmentandyourpressurewasher.The
special formula won’t clog the suction
tube filter and will protect the internal
parts of the pressure washer for a long-
er life. For Kärcher®Detergents, check
your retailer or visit our website:
www.buykarcher.com
CAUTION
Never use:
– Bleach, Chlorine products and other
corrosive chemicals
– Liquids containing solvents (i.e.,
paint thinners, gasoline, oils)
– Tri-sodium phosphate products
– Ammonia products
– Acid-based products
These chemicals will harm the unit and
will damage the surface being cleaned.
Use of these items will void the war-
ranty.
STEP 1:
Release trigger and engage gun
safety lock.
STEP 2:
Turn pressure washer to OFF (0) po-
sition.
TAKING A BREAK ..five minutes or more

10 English
STEP 1:
Turn the switch to OFF (0) position
and unplug cord from outlet.
STEP 2:
Turn off the water source.
STEP 3:
Press trigger to release water pres-
sure.
STEP 4:
Release trigger and engage gun
safety lock.
STEP 5:
Disconnect the garden hose from
the water inlet on the unit.
STEP 6:
Disconnect the garden hose from
the water inlet on the unit.
SHUTTING DOWN & CLEAN-UP

English 11
1: Disconnect all water connections.
2: Turn on the machine for a few
seconds, until the water which had
remained in the pump exits, turn off
immediately.
3: Do not allow high pressure hose
to become kinked.
4: Store the machine and accesso-
ries in a room which does not reach
freezing temperatures. DO NOT
store near furnace or other sources
of heat as it may dry out the pump
seals.
CAUTION
Failure to follow the above directions
will result in damage to the pump as-
sembly and accessories and will void
the warranty.
Kärcher®also recommends the regular
practice of using a pump protector like
“Kärcher®Pump Guard” to prevent cold
weather damage during storage in the
winter months.
STEP 1:
Pull out washer from the water inlet.
STEP 2:
Pull out water inlet filter with flat-
nose pliers.
STEP 3:
Rinse out water inlet filter in warm
water.
STEP 4:
Reinsertwaterinletfilter and washer
into the water inlet.
The unit is maintenance-free.
WINTERIZING AND LONG-TERM STORAGE
CARE AND MAINTENANCE INSTRUCTIONS
Cleaning the water inlet filter
Maintenance

12 English
CAUTION
Before cleaning any surface an in-
conspicuousareashouldbecleaned
totest spray patternand distancefor
maximum cleaning results.
If painted surfaces are peeling or
chipping, use extreme caution as
pressure washer may remove the
loose paint from the surface.
Whenusingonsurfaceswhichmight
come in contact with food, flush sur-
faces with plenty of drinking water.
For additional cleaning tips and a
complete video library, visit our web-
site:
www.karcherresidential.com
(with or without detergent). Pre-rinse
deck and surrounding area with fresh
water. If using detergent, apply to sur-
face at low pressure. For best results,
limit your work area to smaller sections
of approximately 25 square feet. Allow
detergent to remain on surface 1-3 min-
utes. Do not allow detergent to dry on
surface.Rinseathighpressureinalong
sweeping motion keeping the spray
nozzle approximately 3-6 inches from
thecleaning surface.Alwaysclean from
top to bottom and from left to right.
When moving on toa new section of the
cleaning surface, be sure to overlap the
previoussectiontoeliminatestopmarks
andensureamoreevencleaningresult.
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing detergent, apply to surface at low
pressure (for best results, limit your
work area to sections of approximately
6 feet and always apply detergent from
bottom to top). Allow detergent to re-
main on surface 1-3 minutes. Do not al-
low detergent to dry on surface, if
surface appears to be drying, simply
wet down surface with fresh water. If
needed, use special wash brush attach-
ment (not included) to remove stubborn
dirt. Rinse at high pressure from top to
bottom in an even sweeping motion
keepingthespraynozzleapproximately
6 inches from the cleaning surface.
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing detergent or Degreaser, apply to
surface at low pressure. For best re-
sults, limit your work area to smaller
sections of approximately 25 square
feet. Allow detergent or Degreaser tore-
main on surface 1-3 minutes. Do not al-
low detergent to dry on surface. Rinse
at high pressure in a sweeping motion
keepingthespraynozzleapproximately
3-6 inches from the cleaning surface.
Always clean from top to bottom and
from left to right. For removing extreme-
ly stubborn stains, use the Dirtblaster®
Nozzle.
(with or without detergent). Pre-rinse
vehicle with fresh water. If using deter-
gent, apply to surface at low pressure.
For best results, clean one side of vehi-
cleatatimeandalwaysapplydetergent
from bottom to top, do not allow deter-
gent to dry on surface. If needed, use
special wash brush attachment (not in-
cluded) to remove stubborn dirt. Rinse
at high pressure in a sweeping motion
CLEANING TIPS
Deck Cleaning
House Siding
Cement Patios, Brick and Stone
Cars, Boats & Motorcycles

English 13
keepingthespraynozzle approximately
6-8 inches from the cleaning surface
(distance should increase when rinsing
pin-striping or other sensitive surfaces).
Always clean from top to bottom and
from left to right. For best results, wipe
surface dry with a chamois or soft dry
cloth.
(with or without detergent). Pre-rinse
cleaning surface with fresh water. If us-
ing detergent or Degreaser, applydeter-
gent at low pressure. Allow detergent to
remain on surface 1-3 minutes. Do not
allow detergentto dry on surface. Rinse
at high pressure keeping the spray noz-
zle approximately 3-6 inches from the
cleaning surface. For removing ex-
tremely stubborn dirt, it may be neces-
sary to move the spray nozzle even
closer to the surface for greater dirt cut-
ting action.
(with or without detergent). Pre-rinse
furniture and surrounding area with
fresh water. If using detergent, apply to
surfaceatlowpressure.Allowdetergent
to remain on surface 1-3 minutes. Do
not allow detergent to dry on surface. If
neededuse special Wash BrushAttach-
ment (not included) to remove stubborn
dirt. Rinse at high pressure in a sweep-
ing motion keeping the spray nozzle ap-
proximately 3-6 inches from the
cleaningsurface.Forbestresults,clean
from top to bottom and from left to right.
Barbecue Grills, Outdoor Power
Equipment & Gardening Tools
Patio & Lawn Furniture

14 English
Optional accessories are available to
further enhance your cleaning capabili-
ties.Theseaccessories areaccurateas
of the printing date of this manual.
Please check our website for pricing
and up-to-date information.
Specially formulated to protect your
pressure washer from freezing, corro-
sion and premature wear. The Pump
Guard also adds lubrication to valves
and seals to prevent sticking. Highly
recommended for all Kärcher®pressure
washers!
Part No. 9.558-998.0
Replacement hose fits Kärcher®pres-
sure washer with screw-on type gun
connections from 2400 PSI to
2500 PSI, Extension Hose for all
Kärcher®high pressure washers be-
tween the original equipment hose and
machine up to 2500 PSI.
Part No. 2.640-850.0
Need to clean second story windows or
other high areas? Increase the reach of
your pressure washer by up to 66" with
this extension kit. Includes 4 aluminum
sections for variable length. 66" fully as-
sembled. Fits most Kärcher®pressure
washers up to 2300 PSI. (bayonet)
Part No. 2.640-746.0
For more effortless cleaning of all
smooth surfaces (painted, glass and
plastic) try the Kärcher®Rotating Wash
Brush.Useitonyourautomobile,house
siding or windows. The water pressure
from your pressure washer causes the
inner brushes to gently spin, making
your cleaning job much easier. The an-
gle of brush head is adjustable to help
you reach difficult areas. Excellent for
the application of detergent. A must-
have accessory designed for Kärcher®
pressure washers up to 2300 PSI. (bay-
onet)
Part No. 2.640-743.0
Madewithsoft bristles that will notharm
painted surfaces. Easily attaches direct-
ly to the trigger gun. Ideal for stubborn
dirt on cars, boats, patio furniture and
other surfaces. Great forapplying deter-
gent. Fits most Kärcher®pressure
washers up to 2300 PSI. (bayonet)
Part No. 2.640-740.0
Need to clean blocked pipes, drains or
downspouts? The Kärcher®pipe clean-
ing kit is the answer! The pipe cleaner
propels itself forward while simulta-
neously flushing out debris. For exam-
ple, insert the cleaning nozzle in the
baseof a downspout,pull the trigger on
the pressure washer gun and watch as
the nozzle shoots out leaves and other
debriswhile climbing upward. Connects
directly to the trigger gun of most
Kärcher®pressure washers up to
2300 PSI. (bayonet)
Part No. 2.640-747.0
Whyspendhoursstrippingoldpaintand
rust by hand using harsh chemicals?
Let the Kärcher®Wet Sandblasting Kit
do the work! Attach the kit to your pres-
OPTIONAL CLEANING ACCESSORIES
Pump Guard
25 Ft. Extension /Replacement
High-Pressure Hose
66" Extension Wand (Four piece)
Rotating Wash Brush (bayonet)
Soft Clean Washing Brush
25 ft. Pipe Cleaning Kit (bayonet)
Wet Sandblasting Kit (bayonet)

English 15
sure washer, add abrasive material and
attack the rust and paint with our eco-
friendly alternative. Fits most Kärcher®
pressure washers up to 2300 PSI. (bay-
onet)
Part No. 2.638-792.0
Ideal for applications which require a
thick foam. Simply fill the resevoir cup
withliquidpressurewasherdetergentto
generate a foam spray. Connects di-
rectly to the trigger gun. Fits most
Kärcher®pressure washers up to
2300 PSI. (bayonet)
Part No. 6.964-507.0
For cleaning surfaces such as patios,
terraces and driveways without splash-
back,thereisno better solutionthan the
Kärcher®T 100. It saves time by clean-
ing a one foot wide area gently as it hov-
ers, providing consistent, streak-free
cleaning. When you finish cleaning the
patio and driveway, remove the wand
and use the handle to clean garage
doors and other vertical surfaces. In-
cludes two nozzles which spin at high
speed for optimum results. Our top sell-
ing accessory for Kärcher®pressure
washers up to 2300 PSI. (bayonet)
Part No. 2.640-959.0
Detergent Foamer Attachment
T 100 Wide Area Surface Cleaner

16 English
CAUTION Disconnectthemachine fromthepower
source before making any repair.
TROUBLESHOOTING
Symptom Cause Solution
Motor will not start On/Off switch is in the “OFF”
(0) position. Turn switch to the “ON” (I) posi- tion
Power cord is not plugged in. Plug in power cord.
Electricaloutletdoesnotsup-
ply adequate power. Try a different outlet.
Tripped GFCI plug. Press“RESET”buttononGFCI
plug.
Tripped circuit breaker. Switch off pressure washer.
The reset comes automatically
once the temperature of the
unit drops.
Unit does not
reach high pres-
sure.
Diameter of garden hose is
too small. Replace with a 5/8 inch or larg- er garden hose.
Water supply is restricted. Check garden hose for kinks,
leaks and blockage.
Not enough inlet water sup-
ply. Open water source full force.
Water inlet filter is clogged. Remove filter and rinse out in
warm water.
Spray wand is on low pres-
sure position. Turn spray wand to high pres- sure position.
Output pressure
varies high and
low.
Not enough inlet water sup-
ply. Turn water on full force. Check garden hose for kinks, leaks or
blockage.
Pump is sucking air. Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
triggergununtilasteadyflowof
water emerges through the
nozzle.
Water inlet filter is clogged. Remove filter and rinse out in
warm water.
Discharge nozzle is obstruct-
ed. Blow out or remove debris with a fine needle.
Calcified gun, hose or spray
wand. Run distilled vinegar through detergent suction tube.

English 17
If you encounter any additional difficul-
ties not listed, please visit our website.
USA / Canada:
www.karcher-help.com
México:
www.karcher.com.mx
No detergent. Detergent suction tube not
properly connected to the
machine.
Check connection.
Detergent is too thick. Dilute detergent, for best re-
sults use Kärcher®detergent.
Filter on detergent suction
tube is clogged. Run warm water through filter to remove debris.
Damaged or clogged deter-
gent suction tube. Remove obstruction or replace detergent suction tube.
Spray wand is in high pres-
sure position. Turn spray wand tip to low pressure position.
Discharge nozzle is obstruct-
ed. Blow out or remove debris with fine needle.
Garden hose con-
nection leaks. Loose fittings. Tighten fittings.
Missing/worn rubber washer. Insert new washer.
Spray wand leaks. Spray wand not properly at-
tached. Insert the spray wand into the trigger gun. Carefully press in
against the spring tension and
twist into the locked position.
Broken o-ring or plastic in-
sert. Call Customer Support
Pump is noisy. Pump is sucking air. Check that hoses and fittings
are air tight. Turn off machine
and purge pump by squeezing
triggergununtilasteadyflowof
water emerges through the
nozzle.
Water leaks from
pump (up to 10
dropsperminuteis
permissible).
Loose fittings. Check that all fittings are tight.
Water seals are damaged or
worn. Call Customer Support
Oil Drip. Oil seals are damaged or
worn. Call Customer Support
Symptom Cause Solution

18 Français
DANGER
Identifie “une situation de danger immi-
nent qui, si elle n'est pas évitée, entraî-
ne la mort ou des blessures graves”.
AVERTISSEMENT
Identifie “une situation de danger poten-
tiel qui, si elle n'est pas évitée, pourrait
entraîner la mort ou des blessures”.
ATTENTION
Identifie “une situation de danger poten-
tiel qui, si elle n'est pas évitée, peut
éventuellemententraîner desblessures
légères ou modérées” ou des domma-
ges matériels.
A usage domestique seulement !
Avantd'utiliserce nettoyeur pression, le
propriétaire et/ou l'utilisateur doit impé-
rativement avoir pris connaissance des
consignes d'utilisation et mises en gar-
de du fabricant.
Il est nécessaire d'insister sur les aver-
tissements et de les comprendre.
Si l'utilisateur ne parle pas couramment
l'anglais, l'acheteur/le propriétaire doit
lire les consignes et mises en garde du
fabricant avec l'utilisateur dans la lan-
gue maternelle de ce dernier et s'assu-
rer qu'il en comprend bien le contenu.
Le propriétaire et/ou l'utilisateur doit se
familiariser avec les consignes du fabri-
cant et les conserver afin de pouvoir s'y
référer ultérieurement.
Pour faire valoir une demande en ga-
rantie, appeler : 1-800-537-4129. Tous
lesautresinformationssont disponibles
sous : www.karcher-help.com
Prenez le temps d'enregistrer votre net-
toyeur haute pression en ligne en vous
adressant à
www.karcher-register.com. Veillez à
conserver précieusement votre bon
d'achat, dont la présence est nécessai-
re en cas de réparation sous le couvert
de la garantie.
Appeler : 01-800-024-13-13 pour obte-
nir de l'aide ou visiter notre site Web :
www.karcher.com.mx
NETTOYEUR HAUTE PRESSION - MANUEL D'UTILISATION
Généralités 19
Consignes de sécurité importantes 20
Instructions de montage 23
Mode d'emploi 23
Utilisation des accessoires 25
Emploi de détergents 25
Prendre une pause 26
Arrêt de l'appareil et nettoyage 27
Entreposage à long terme 28
Consignes d'entretien 28
Conseils de nettoyage 29
Accessoires de nettoyage en option 31
Dépannage 33
Symboles d'alerte de sécurité
Caractéristiques
Pression max. 2000 PSI
Débit d'eau max. 1.4 GPM
Ampérage 13 AMPS
Tension 120 V
N° de pièce 1.601-776.0
N° de série
Responsabilité du propriétaire/
de l'utilisateur
Service client USA et Canada
Assistance Mexique

Français 19
1 Entrée d'eau avec raccord pour
tuyau d'arrosage
2 Sortie haute pression
3 Interrupteur marche/arrêt
4 Réservoir de détergent (amovible)
5 Support pour la poignée-pistolet
6 Poignée de transport
7 Compartiment de rangement des ac-
cessoires
8 Cordon d'alimentation avec disjonc-
teur différentiel
9 Roues
10 Poignée-pistolet
11 Verrouillage de sécurité de la poi-
gnée-pistolet
12 Touche pour séparer le flexible hau-
te pression de la poignée-pistolet
13 Tuyau à haute pression
14 Dirtblaster®(lance rotative)
15 Lance Vario
16 Brosse de lavage
GÉNÉRALITÉS

20 Français
AVERTISSEMENT
En utilisant ce produit, toujours obser-
ver une certaine prudence élémentaire,
incluant notamment:
Afin de minimiser les risques de
blessure, ne jamais laisser l'appareil
sanssurveillancelorsquecelui-ciest
utilisé à proximité d'enfants.
Il est impératif de savoir arrêter et
mettre l'appareil hors pression rapi-
dement. Une connaissance appro-
fondie des commandes est
nécessaire.
Rester attentif – se concentrer sur la
tâche en cours.
L'utilisateur ne doit jamais faire usa-
ge de l'appareil lorsqu'il est fatigué
ou sous l'emprise d'alcool ou de dro-
gues.
Veiller à ce qu'aucun individu ne se
trouve dans la zone de travail.
Ne jamais passer ou monter sur des
supports instables. Toujours rester
stable et équilibré.
Respecter les consignes d'entretien
figurant dans le manuel.
Ce produit est fourni avec un dis-
joncteur différentiel monté dans la fi-
che du cordon d'alimentation. Si le
remplacement de la fiche ou du cor-
don d'alimentation s'avère nécessai-
re, n'utiliser que des pièces de
rechange identiques.
AVERTISSEMENT
Risque de projection ou de blessure
– Ne pas diriger le jet de vapeur en
direction d'individus.
En cas d'utilisation incorrecte, les
jets haute pression peuvent être
dangereux.Ne jamais diriger les jets
de vapeur en direction d'individus,
d'animaux, de dispositifs électriques
ou de l'appareil lui-même.
Le port de lunettes de protection est
obligatoire.
AVERTISSEMENT
Risque d'explosion – Ne pas vapori-
ser de liquides inflammables.
N'utiliser en aucun cas d'acides, de
solutions alcalines, de solvants ou
de produits inflammables dans cet
appareil. Ces produits peuvent être
à l'origine de blessures graves ou
d'endommagement irréversible de
l'appareil.
ATTENTION
Le pistolet génère une force de pro-
pulsion – Le maintenir toujours à
deux mains.
Le dispositif de sécurité de la poi-
gnée-pistolet permet d'éviter tout ac-
tionnement accidentel de la
gâchette. Ce dispositif de sécurité
NE verrouille PAS la gâchette en po-
sition marche (ON).
AVERTISSEMENT
– Risque d'électrocution
Examinerlacordonavantdel'utiliser
– Ne pas utiliser de cordon endom-
magée.
Garder toutes les connexions au sec
et ne pas les laisser à terre.
Ne pas toucher la fiche avec les
mains mouillées.
Ne pas utiliser que des rallonges.
Brancher à une dérivation distincte.
CONSIGNES DE SÉCURITÉ IMPORTANTES