KaVo ProXam Extraoral User guide

installation quick guide
KaVo ProXam Extraoral
1.015.1972

MOUNTING ACCESSORIESTOOLS REQUIRED
Felt pads ø24 (12 pcs)
Expansion anchor ø10x50
Washer ø8,4/17 DIN 125
Screw M8x50 DIN 571
Mounting accessories Adjustable wall support
Expansion anchor ø14x70
Washer ø10.5/21 DIN 125
Screw M10x70 DIN 571
Protective cap
Cover plug 7-8 mm
Cover plug 10 mm
1. Tape measure
2. Flat head screwdriver
3. Phillips head screwdriver
4. Pencil
5. Spirit level
6. Hammer drill
7. Box cutter
8. Electrical tape
9. Metric Allen key set
10. Metric open end key set
11. Torx key TX08 and TX25
1
6 7 8 9 10 11
2 3 4 5
Torx key
Torx key
TX25
TX08
1000
39,4”
Unit dimensions = 1300 / 51,2”
Unit dimensions = 1730-2390 / 68,1”- 94,1”
Unit dimensions = 1320-2100 / 52,0”- 82,7”
1250
49,2”
Unit dimensions = 756,5 / 29,8”
725 / 28,5” with minimum wall support lenght
Unit dimensions = 2120 / 83,5”
Minimum recommended space = 2220 / 87,4”
Unit dimensions = 1400 / 55,1”
1380 / 54,3” with minimum wall support lenght
Minimum recommended space = 1450 / 57,0” 1430 / 56,3” with minimum wall support lenght
1170
ProXam 3DQ
46.0”
950 (50)
37,4” (2,0”)
(50)
(2,0”)
350
13,8”
(50)
(2,0”)
KaVo_ProXam_IP1.eps

Package 1
1. KaVo ProXam X-ray unit
2. Stationary column side covers
3. Shoulder arm cover
4. Accessories box
1
2
3
4
Package 2 (3D system)
1. Ethernet switch
2. 3D sensor
3. Reconstruction PC (RecoPC)
1
3
2
1
2
3
4
5
6
1
2
3
4
5
6
7
14
5
3
2
3
A
A
B
B
IF B
B
B
Remove
Remove
13
Adjust
Adjust
Distance
Unscrew ½
2
Unscrew ½
Tighten
Tighten
4
Adjust the adjustable
wall support if needed.
UNPACKING
(CARDBOARD SHIPPING CRATE)
UNPACKING
(WOODEN SHIPPING CRATE)
DELIVERY CONTENTS
ADJUSTABLE WALL SUPPORT
Adjust KaVo ProXam distance from
wall with the adjustable
wall support if needed.
KaVo_ProXam_IP2.eps

1
2
5
6
1250 mm
1234
Wall made of concrete or stone
Wooden wall
NOTE! The wall support installation must
be able to resist a pull-out force of 3310 N
(338 kg; 744 lb)
3310 N
(338 kg; 744 lb)
Or
A
B
1
2
2
3
3
1
1
2
3
1234
5
6
3
4
5
1
1
IF B
2
B
A
3
3
1
2
4
4
ATTACHING X-RAY UNIT TO WALL AND FLOORLIFTING UP X-UNIT
KaVo_ProXam_IP3.eps

5
6
1250 mm
1234
Wall made of concrete or stone
Wooden wall
Or
A
BNOTE! The wall support installation must
be able to resist a pull-out force of 3310 N
(338 kg; 744 lb)
3310 N
(338 kg; 744 lb)
1
2
2
3
3
1
125mm
180°
3
2
1
1
24
Adjust, see page2
3
1
1
4
3
5
IF B
2
B
A
3
4
2
1
1
ATTACHING X-RAY UNIT TO WALL WITH
SECOND ADJUSTABLE WALL SUPPORT
KaVo_ProXam_IP4.eps

1
3
2
2
2
12
3
MAINS SUPPLY
3 x 2,5 mm2 (100-220 VAC, 16A T 250V)
3 x 1,5 mm2 (230-240 VAC, 10A T 250V)
Remove a knockout in the juction box.
Attach strain relief to the junction box
PE
Mains
Junction box
Blue
Brown
Yellow / Green
(Earth)
Blue
Brown
Yellow / Green
(Earth)
X-ray unit power cable
L
LN PE
N
CONNECTING MAINS CABLE
L
N
12
3
4
KaVo_ProXam_IP5.eps
X-RAY UNITS WITH DETACHABLE
POWER SUPPLY CORD
13
2
REMOVE THE TRANSPORT LOCKING BARUNSCREW THE TRANSORT LOCKING BAR
REMOVE THE SUPPORT
FRAME AND STYROFOAM
PACKAGING

INSTALLING MOVABLEREMOVING TRANSPORT LOCKING
PIN (90kV ROTATING TUBE HEAD) EXPOSURE SWITCH
INSTALLING STATIONARY
EXPOSURE SWITCH
CONNECTING EXPOSURE
SWITCH CABLE
CONNECTING CABLES ON 2D
SYSTEMS
Romexis PC
Cat 6
Clinic network
1 2
12 3 4 1
2
KaVo_ProXam_IP6.eps

1 2
43 5
Reconstruction PC
Ethernet switch
Cat 6
Cat 6
12345678
Romexis PC
Clinic network
Cat 6
1
2
3
CONNECTING CABLES ON 3D SYSTEMS
ATTACHING COVERS
ATTACHING SENSOR HEAD
REMOVING ESD TAPE
KaVo_ProXam_IP7.eps

POST-INSTALLATION CHECKLIST
Panoramic/SmartPan calibration
POST-INSTALLATION CHECKLIST
Customer :___________________________________ Serial number :__________________________
Installation location :___________________________________ Installation date :__________________________
Software version
Unit :___________________________________
3D Sensor :___________________________________
Reco PC :___________________________________
Beam check...........................................................................................
Flat field calibration................................................................................
Ball phantom test...................................................................................
SmartPan with MultiView calibration......................................................
3D calibration
3D beam check......................................................................................
3D flat field calibration............................................................................
3D geometry calibration.........................................................................
3D quality assurance (Q/A) test.............................................................
KaVo ProXam Cephalostat calibration
(If the X-ray unit is equipped with cephalostat)
Beam check...........................................................................................
Flat field calibration................................................................................
X-ray unit mechanical movements
Check the column movements (up/down)..............................................
Emergency stop button and plate
Check the emergency stop button functionality.....................................
Check the column movement emergency stop plate functionality.........
Patient positioning lights
Check the patient positioning lights.......................................................
Imaging tests
Other:
_______________________________________________________
_______________________________________________________
_______________________________________________________
_______________________________________________________
Technician’s signature:________________________ Date:________
Customer’s signature :________________________
Take test captures for
the following programs (if available in the X-ray unit).
Model/Program Pan Ceph Tooth Teeth Jaw Face
----2D
--3D
3DQ
KaVo_ProXam_IP8.eps

www.kavo.com