Keisue KES3.0 Micro Farm User manual

Installation and Operation Manual
State of the Art: KES3.0 Micro Farm

-1- -2-
State of the Art: KES3.0 Micro Farm
Installation and Operation Manual
Please read through the user manual for the best user
experience.
GMC PSE ROHS CE-LVD CE-EMC FCC
Product specication and accessories
Ready to start
Function Description
Cleaning and Caring
Safety Precautions
3
5
7
9
11

-3- -4-
Product specication and accessories
Front side Back side
Water container
Base
Function buttons
Adjustable stand
Product specication of KES 3.0 Micro Farm
Accessories of KES 3.0 Micro Farm
LED growth light
“LIGHTING”
button
“WATER”
button
“POWER”
button
Planting board
Water pump
Power Supply Connection
Adjustable stand
Water Supply Connection
Hydroponic nutrient
solutions A and B
Planting
baskets
Mixing
rod
ForcepsHydroponic
sponges
Seeds EC Tester

1. Tools Preparation
Seeds, hydroponic sponges, hydroponic nutrient solution A,
hydroponic nutrient solution B, planting baskets, forceps
Reminder: Use tap water or mineral water as the water sources for cultivation.
2. Seed soaking
Prepare 6 seeds. Soak the seeds in water (20 - 30 ℃ ) using a
container for 2 to 3 hours.
Reminder : it is advised that 1 seed per sponge for planting.
3. Seedlings grow
A. Prepare and separate 6 pieces of
hydroponic sponges. See Figure 1.
B. Soak the sponges into water with 3-5
times light press. Squeeze out air for
keeping the sponges moist.
C. Put the soaked seeds into the " cross
mark" of the hydroponic sponges to
fix the seeds positions and absorb
adequate water. See Figure 2.
D. Fix the sponges in planting baskets.
The sponges should be in touch with
-5- -6-
Ready to start
Ready to start
the bottom of planting baskets. See Figure 3.
Reminder: The hydroponic sponge should be fixed at the bottom of planting
basket to ensure adequate absorption of water.
E. Install the water pump at the
water container center.
F. Add water into the container
until reaching the interval of
“5”. The intervals are shown
in the inner surface of the
container. See Figure 4.
G. Connect the water pump to
the power supply "PUMP"
located at the stand back. See
Figure 5.
H. Cover the container with
planting board. Place all the
planting baskets prepared in (3)
on the board.
I. Connect the power source. Press
the“POWER” button, followed
by the “WATER” button.
See Figure 6.
Seeds
×✓
Hydroponic nutrient
solution A and B
Planting baskets Hydroponic sponges Forceps

-7- -8-
Function Description
Function Description
The illustration of control panel
The illustration of buttons
Press the “POWER” button when the power supply is connected.
The default time setting for this product is 06:00.
Press the “WATER” button and “LIGHTING” button. The default
time setting for water and lighting operation is from 06:00 to 21:59.
To Switch o the machine, press the “POWER” button, the water
and lighting supply will shut down simultaneously.
Reminder: If the power supply is disconnected for a few hours, the machine will
resume default setting when reconnected.
The setting of “LIGHTING”
Press down the “LIGHTING” button for 3 seconds until it ashes
toenter the setting mode of light intensity. There are 4 modes of
light intensity.
Mode 1: The “LIGHTING” button flashes once in 1.5 seconds,
the light intensity is 25%.
Mode 2: The “LIGHTING” button ashes twice in 1.5 seconds,
the light intensity is 50%.
Mode 3: The “LIGHTING” button flashes three times in 1.5
seconds, the light intensity is 75%.
Mode 4: The “LIGHTING” button flashes four times in 1.5
seconds, the light intensity is 100%.
Choose mode by clicking the "LIGHTING" button in the setting
mode. Press down 3 seconds to exit the setting.
The setting of “WATER”
Press down the “WATER” button for 3 seconds until it ashes
to enter the setting mode of water cycle frequency. There are 4
dierent modes of water cycle frequency.
Mode 1: The “WATER” button ashes once in 1.5 seconds. The
water cycle operates for 5 minutes in every hour.
Mode 2: The “WATER” button ashes twice in 1.5 seconds. The
water cycle operates for 5 minutes in every 4 hours.
Mode 3: The “WATER” button flashes three times in 1.5
seconds. The water cycle operates for 5 minutes for
every 16 hours.
Mode 4: The “WATER” button flashes four times in 1.5
seconds.
The water cycle operates for the entire 16 hours. Choose mode by
clicking the "LIGHTING" button in the setting mode. Press down 3
seconds to exit the setting.
Lighting button Water button Power button
The operation time of electric water pump for dierent modes
Time slots Mode 1 Mode 2 Mode 3 Mode 4
6:00-6:05
6:00
22:00
7:00-7:05
8:00-8:05
9:00-9:05
10:00-10:05
11:00-11:05
12:00-12:05
13:00-13:05
14:00-14:05
15:00-15:05
16:00-16:05
17:00-17:05
18:00-18:05
19:00-19:05
20:00-20:05
21:00-21:05
22:00-22:05
Table 2

5. To set product time, Press the "POWER" button to switch on
the machine. Press down the "POWER" button for 3 seconds
for auto dealt time setting (08:00am). The setting nish when
the "POWER" button ashes for 3 times.
Cleaning
To maintain a clean environment for plantation, it is advised that
the planting board and water container should be washed after
harvest. Please avoid making the plug wet.
1. Machine cleaning: Switch o the "POWER" button. Disconnect
the power supply and water pump. Dispose the waste water and
dry the machine at ventilation location.
2. Hydroponic sponge: Consumable. Dispose after planting.
3. Planting baskets: Reusable. Clean and reuse after planting.
Reminder: Please use neutral detergents for cleaning.
-9- -10-
Cleaning and Caring
Cleaning and caring
Carring
1. Please strictly follow the instructions of this user manual. It
is advised to use the default mode of this model for the best
user experience.
2. Avoid making the plug and cables wet when cleaning.
3. This product is designed for indoor use only. Avoid direct
illumination of sunlight. To avoid accidents, place the
product on a at surface. To ensure ventilation, the back of
the machine should have a minimum distance of 10 cm with
the wall.
Malfunctioning and solution
There is a protection function for water pump. Water pump would
not operate with 2 situations:
- Water level is too low
- No water in the water container while the "WATER" button is
switched on
Solution:
- Switch o the "WATER" button and add water to level "1" in the
container.
- Check the connection of water pump power.
If the water pump is still malfunctioning after switch on the water
pump, contact the distributor for assistance and maintenance.

-11- -12
-
Safety precautions
Safety precautions
General safety precautions
● Disconnect the power supply before cleaning or carrying out
maintenance. Do not touch with wet hands. Ensure the power
and cables are dry before reconnecting the machine.
● Avoid placing the machine at wet location.
● Disconnect the power supply if the machine is not in use.
● Do not place heavy items on the top of the product to avoid
damaging the LED light stand.
● The voltage of this product is from 100V AC to 240V AC.
Please ensure the source of power supply is suitable for
operating the product.
● Use water and neutral detergents to clean the machine.
Avoid using metal brushes, alcohol, etc. Torn and wear of this
product could lead to growth of bacteria.
● Contact the distributor for assistance and maintenance if the
product is malfunctioning.
● The manufacturer of this product is not liable to bear any
responsibility of damages because of improper usage and
man-made damages. The above situations are not entitled
to one-year warranty that users have to pay for maintenance
costs.
● The product is made for plantation only. Do not use it for other
purposes.
● Do not look directly at the LED light to avoid eye discomfort.
Safety precautions during planting
Please read through the following instructions when using this product
for planting:
1. When mixing the nutrient solution, adding water or sowing,
please keep your hands clean to avoid growth of bacteria that
hinders the growth of plants.
2. Use disposable gloves to prevent allergy.
3. Follow strictly on the ratio of mixing the nutrient solution to
ensure better growth of plants. Avoid using other brands of
hydroponic nutrient solution.
4. Use tap water as the medium to grow plants. As the pH value for
tap water is slightly alkaline, it is advised to use pH calibrating
solutions when adding nutrient solution to the solution mix so as
to adjust and keep the pH value of the mix in the range 5.8 to 6.2.
5. The output voltage of this product is DC 12V.
6. Ensure the water level container water level is at interval "1"
before switch on the water pump.
Product specications
Product Name : KES 3.0
Power Source : 100V AC-240V AC
Output voltage : 27W
Dimension : 400mm x 268mm x 238mm (lowest)
 400mm x 268mm x 375mm (highest)
Weight : 3.2 kg (Net weight) / 4.3 kg
Colour : Black, White, Baby Blue, Pink
Please register for the one-year warranty at
https://www.mpoint.com.hk/warranty
The terms and conditions for warranty can be found in the above
website.