Kenmore 75085 8,000 User manual

Owner's Manual
Manual del Propietario
®
THROUGH-THE-WALLAIRCONDITIONER
ACONDIClONADODEAIREATRAVESDEPARED
Model, Modelo 580.75085
Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179
www.sears.com

TABLE OF CONTENTS ........................2
WARRANTY ..............................................2
SAFETY .....................................................3
Important Safety Instructions ...................... 3
ELECTRICAL REQUIREMENTS .......4
INSTALLATION ........................................5
Installation Requirements ......................... 5
Installation ................................................ 6
Procedure A ............................................. 7
Procedure B ............................................. 8
Procedure C ........................................... 10
OPERATION ...........................................12
How and Why ......................................... 12
Normal Sounds ...................................... 12
Capacity and Running Time ................... 12
Features ................................................. 13
Using the Air Conditioner ....................... 13
Control Panel ......................................... 14
Remote Control ...................................... 15
MAINTENANCE .....................................17
Air Filter Cleaning ................................... 17
Air Conditioner Cleaning ........................ 17
How to Remove the Front Grille ............. 17
How to Replace the Front Grille ............. 17
TROUBLESHOOTING .........................18
Before Calling for Service ...................... 18
ESPAI_IOL ................................................20
MASTER PROTECTION
AGREEMENTS ......................................39
SERVICE NUMBERS ............ Back Cover
FULL ONE YEAR WARRANTY ON
THROUGH-THE-WALL AIR CONDITIONER
For one year from the date of purchase, when this
air conditioner is operated and maintained for
normal room cooling according to instructions in this
owner's manual, Sears will repair this air
conditioner, free of charge, if defective in material or
workmanship.
FULL FIVE-YEAR WARRANTY ON
SEALED REFRIGERATION SYSTEM
For five years from the date of purchase, when this
air conditioner is operated and maintained for
normal room cooling according to instructions in this
owner's manual, Sears will repair the sealed
refrigeration system (consisting of refrigerant,
connecting tubing, and compressor), free of charge,
if defective in material or workmanship.
WARRANTY SERVICE IS AVAILABLE BY
CONTACTING SEARS SERVICE AT
1-800-4-MY-HOME ®.
Warranty coverage applies only to air conditioners
used for non-commercial, private household
purposes.
This warranty applies only while this product is in
use in the United States.
This warranty gives you specific legal rights, and
you may also have other rights which vary from
state to state.
Distributed by Sears, Roebuck and
Co., Hoffman Estates, IL 60179
-2-

IMPORTANT SAFETY INSTRUCTIONS
The safety instructions below will tell you how to use your room air conditioner to avoid harm to yourself or
damage to your ROOM AIR CONDITIONER.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance. Read product labels for flammability and
other warnings.
PREVENT ACCIDENTS
To reduce the risk of fire, electrical shock, or injury
to persons when using your air conditioner, follow
basic precautions, including the following:
• Be sure the electrical service is adequate for the
model you have chosen.
• If the air conditioner is to be installed in a window,
you will probably want to clean both sides of the
glass first. Ifthe window is a triple-track type with a
screen panel included, you may want to remove
the screen completely before installation.
• Be sure the air conditioner has been securely and
correctly installed according to the instructions in
this manual.
Save this manual and installation instructions for
possible future use in removing or reinstalling this
unit.
• Use gloves when handling the air conditioner.
Be careful to avoid cuts from sharp metal fins on
front and rear coils.
ELECTRICAL INFORMATION
The complete electrical rating of your new room air
conditioner is stated on the serial plate. Refer to the
rating when checking the electrical requirements.
• Be sure the air conditioner is properly grounded.
To minimize shock and fire hazards, proper
grounding is important. The power cord is
equipped with a three-prong grounding plug for
protection against shock hazards.
• Your air conditioner must be plugged into a
properly grounded wall receptacle. Ifthe wall
receptacle you intend to use is not adequately
grounded or protected by a time delay fuse or
circuit breaker, have a qualified electrician install
the proper receptacle.
• Do not run air conditioner with packing sheet of
the back of the sleeve, and packing corner and
blue tape of the air conditioner. This could result in
mechanical damage within the air conditioner.
• Do not use an extension cord or an adapter
plug.
_ Avoid fire hazard or electric shock.
Do not use an extension cord or an adapter plug.
Do not remove any prong from the power cord.
Grounding type
wall receptacle Do not under any
circumstances cut,
remove, or bypass
the grounding prong
from this plug.
Reset
Power supply cord _- ,_r-_Lii!/j Test
with 3-prong
grounding plug
ENERGY SAVING IDEAS
• The capacity of the room air conditioner must fit
the room size for efficient and satisfactory
operation.
• Install the room air conditioner on the shady side
of your home. A window that faces north is best
because it is shaded most of the day.
• Do not block air flow inside with blinds, curtains, or
furniture; or outside with shrubs, enclosures, or
other buildings.
• Close the floor and wall registers and the fireplace
damper so cool air does not escape up the
chimney and into the duct work.
• Keep blinds and drapes in other windows closed
during the sunniest part of the day.
• Clean the air filter as recommended in the
MAINTENANCE section of this manual.
• Proper insulation and weather stripping in your
home will help keep warm air out and cool air in.
• External house shading with trees, plants or
awnings will help reduce the air conditioner's work
load.
• Operate heat producing appliances such as
ranges, washers, dryers, and dishwashers during
the coolest part of the day.
-3-

OBSERVE ALL LOCAL CODES AND
ORDINANCES.
DO NOT, UNDER ANY CIRCUMSTANCES,
REMOVE THE POWER SUPPLY CORD
GROUND PRONG.
ELECTRICAL GROUND IS REQUIRED ON
THIS APPLIANCE.
208/230-volt 60 Hz and 115-volt 60 Hz, AC
only, 15A fused and properly grounded
electrical supply is required. A time delay fuse
or time delay circuit breaker is recommended.
Use a dedicated circuit, serving only this
appliance.
DO NOT USE AN EXTENSION CORD.
RECOMMENDED GROUNDING METHOD
For your personal safety, this appliance must
be grounded. This appliance has a power
supply cord with a 3-prong grounding plug. To
minimize possible shock hazard, the cord must
be plugged into a mating grounding type wall
receptacle and grounded in accordance with
the National Electrical Code (ANSI/NFPA 70)
latest edition and all local codes and
ordinances. If a mating wall receptacle is not
available, it is the personal responsibility and
obligation of the customer to have a properly
grounded 3-prong wall receptacle installed by a
qualified electrician.
115V~ T230V~ Power cord may include a current interrupter
device.A test and reset button is provided on the
plug case. Thedevice should be tested on a
periodic basis by first pressing the TEST button
and then the RESET button. Ifthe TEST button
does not trip or if the RESET button will not stay
engaged, discontinue use of the air conditioner and
contact aqualified service technician.
NOTE: The shape may be different accordingto its model.
Use Wall Receptacle Power Supply
Standard 125V,
3-wire grounding
receptacle rated
15A, 125V AC
Standard 250V,
3-wire grounding
receptacle rated
15A, 250V AC
Standard 250V,
3-wire grounding
receptacle rated
20A, 250V AC
Use 15 AMP. time
delay fuse or 15 AMP.
circuit breaker.
Use 20 AMP. time
delay fuse or 20 AMP.
circuit breaker.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
3-prong
grounding ] \_
plug I ,¢>,_'%
I',, 3-prong
Z_I _J I grounding
Reset-F4_..-_/_[l] ,_- Itype wall
Test _i_t ,_ l receptacle
(208/230-volt 60 Hz) (115-volt 60 Hz)
-4-

Remove packing materials from the wall sleeve and tape
from the air conditioner.
INSTALLATION REQUIREMENTS
If you use an existing wall sleeve, you should
measure its dimensions.
Install the new air conditioner according to these
installation instructions to achieve the best
performance. All wall sleeves used to mount the
new air conditioner must be in good structural
condition and have a rear grille to securely attach
the new air conditioner. (FIG. 1)
With the Kenmore sleeve, you can maintain the
best performance of the new air conditioner. (FIG. 2)
20-3/32"
(511 mm) mm)
3/32,,
(366mm)
!8-W32':(466 mm)
Air Conditioner FIG. 1
INSTALLATION HARDWARE
2 Size options
2 Size options
ITEM NAME OF PARTS Q'TY
VERTICAL INSULATION STRIP 1
(_ AROUND INSULATION STRIPS 2
(_) HORIZONTAL INSULATION STRIP 1
SUPPORT BLOCK 2
@ BAFFLE 1
TRIM FRAME 2
@ SHIM 2
_9_ PLASTICNUTSANDWASHERSCREWS 4
GRILLE REAR 1
_ 25.7/s"
(656 mm)
17/32"
[394mm)
Aluminum metal grill_
Kenmore Wall Sleeve (425ram) FIG. 2
ELECTRICAL SERVICE
Check your available electrical service. The power
supply available must be the same as that shown
on the unit nameplate (found on left side of cabinet).
All models are equipped with a 3-prong service plug
to provide proper service and safe positive
grounding. Do not change plug in any way. Do not
use an adapter plug. If your present wall outlet does
not match your plug, call a qualified electrician to
make the necessary corrections. SAVE CARTON
for storage and this OWNER'S MANUAL for future
reference. The carton is the best way to store unit
during winter or when not in use.
-5-
To avoid risk of personal injury, property damage,
or product damage due to the weight of this
device and sharp edges that may be exposed:
• Air conditioners covered in this manual pose an
excessive weight hazard.Two or more people
are neededto move and install the unit.
To prevent injuryor strain, use proper lifting and
carrying techniques when moving unit.
• Carefully inspectlocation where air conditioner
will be installed. Be sure itwill support the weight
ofthe unitover an extended periodof time.
• Handle air conditioner with care. Wear
protective gloves whenever lifting or carrying the
unit. AVOID the sharp metal fins offront and
rear coils.
• Make sure air conditioner does notfall during
installation.
REQUIRED TOOLS:
• Tight Fitting gloves
• Standard screwdriver
• Phillips screwdriver
• Pliers
• Sharp knife
• 3/8-inch open end
wrench or adjustable
wrench
• 1/4-inch hex socket
and ratchet
• Tape measure
• Electric drill
• 1/4-inch drill bit

INSTALLATION
We strongly recommendthe removal of the
old wall sleeve and the installationof a new
Kenmore Wall Sleeve.
Ifyou decideto keep theexistingwallsleeve,
you haveto redirect the louvers atthe back of the
wall sleeve illustration.The use of pliers is
recommended. If you DO NOT redirect,you run
the risk of poor performance or productfailure.
This is not covered under theterms of the
Kenmorewarranty.
Pick a location which will allow the conditioned air
to blow into the area you want. Good installation
with special attention to the proper position of the
unit will lessen the chance that service will be
needed.
ITEMS IN INSTALLATION HARDWARE
You may not need all parts in the kit. Discard
unused parts
ITEM (inches)
Plastic grille
Vertical insulation strip
Around Insulation Strips
Horizontal Insulation Strip
Support Block
Baffle
Shim
Trim Frame
Washer Screw
Nuts(Plastic)
Grille Rear
263/4 X 1 61/2
159/16 X 13/8X 13/8
671/8x 13/8 X25/32
5927/32 X 13/8x 13/8
237/32x 13/8x 13/16
13/4 X 13/8 X 45/16
14 x 41/2 X 1/8
1113/16 X 1 x3/4
Qty.
1
1
1
1
1
2
1
2
2
4
4
1
HOW TO INSTALL
H dentify the existing wall sleeve before installing
the unit from the listed below.
Wall Sleeve Dimensions (inches)
Brand
White-Westinghouse
Frigidaire
Carrier (52F series)
General Electric
/Hotpoint
Width
25-1/2
26
Whirlpool 25-7/8
Fedders/Emerson 27
Sears/Kenmore 25-7/8
Emerson/Fedders 26-3/4
Carrier (51S Series) 25-3/4
Friedrich 27
Height Depth
15-1/4 16, 17-1/2
or 22
15-5/8 16-7/8
17-1/8
16-1/2 or 23
16-3/4 16-3/4
or 19-3/4
15-17/32 16-23/32
15-3/4 15
16-7/8 18-5/8
16-3/4 16-3/4
NOTE: All wall sleeves used to mount the new Air
Conditioner must be in sound structural condition
and have a rear grille that securely attaches to
sleeve, or rear flange that serves as a stop for the
Air Conditioner.
Q
O
Remove old air conditioner from existing wall
sleeve.
Clean the interior of an existing sleeve.
(Do not disturb seals.)
Wall sleeve must be securely fastened in wall
before installing the air conditioner. Use the
nails or screws through sleeve into wall, if
needed. Repaint sleeve if needed.
Prepare the wall sleeve for installation of the
unit. If you plan to use your existing wall sleeve,
and it is not Kenmore, use procedure B or C
below.
Procedure Brand Depth(inches)
A Sears/Kenmore 16-23/32
White-Westinghouse
Frigidaire Carrier 16, 17-1/2
or 22
(52F series)
B General Electric 16-7/8
/Hotpoint
Whirlpool 17-1/8 or 23
Carrier (51S series) 18-5/8
16-3/4
Fedders/Emerson
C or 19-3/4
Emerson/Fedders 15
Friedrich 16-3/4
_ Install new unit into wall sleeve.
CAUTION: When installation is completed,
replacement unit MUST have a rearward slope as
shown. To achieve 1/4" slope, remove the backing
from the 11-13/16" shim strips and attach them as
shown below in Fig. 3. Place the higher portion of
shim to the front of the rib on base of wall sleeve.
1" high[--
I___j 16_j
II 3/4" High
UNIT Wall Sleeve
SHIM PLACEMENT UNIT INSTALLATION
FIG. 3
-6-

PROCEDURE A
li]l If you are using the new sleeve (optionally
supplied with your unit),skip to step 3.
Otherwise, install the plastic grille from the kit.
Cut the plastic grille to 25-1/2" wide and
15-1/4" high. Place the plastic grille to the
inside of the wall sleeve at the rear flange.
FIG. 4
Basten the 4 washer screws to secure the grille
to the wall sleeve. If you need plastic nuts to
mount plastic grille to the inside of the wall
sleeve, there are plastic nuts in the installation
kit. The nuts are installed from the inside of the
sleeve and are pressing into the square holes
of the rear flanges.
or FIG. 5
BRemove the backing from the Vertical
Insulation strip 159/16X13/8x 13/8and attach that
to the inside right of the sleeve as shown
below. Remove the backing from the Around
Insulation strip 671/8x 13/8x 25/32 and attach that
to the inside front of the sleeve as shown
below.
Ir: [,]Etljii[o] I
Indoor Outdoor
9 1/2" -_ _- 6" -_
FIG. 6
L_-I_Remove the metal rear grille and replace it with
the plastic rear grille.
-7
Remove the -Plastic rear grille
metal rear gl
FIG. 7
_ Install the new unit into the wall sleeve.
To assemble trim, snap the tab of each piece
into the slot of the other piece as shown below.
Slide trim over the front of the air conditioner
until trim is flush with sleeve as shown below.
Trim (2 ea) (
Wall
-[
FIG. 8
• Airconditionerscoveredinthismanualposean
excessiveweighthazard.Twoor morepeopleare
neededtomoveandinstalltheunit.
Topreventinjuryor strain,useproperliftingand
carryingtechniqueswhenmovingunit.
• Whenhandlingtheair conditioner,becarefulto avoid
cutsfromsharpmetalfinsonfrontand rearcoils.
• Makesureairconditionerdoesnotfallduring
removal.
• If unitdoesnotoperateafterinstallationcheck,to be
surethecircuitinterrupterhasnotbeentripped.Refer
totheTroubleshootingguidefor resetprocedure.

PROCEDURE B
H edirect the louvers at the back of the wall
sleeve to 60° angle as shown in the FIG 9. The
use of pliers is recommended.
73/32"
Rear Louvers
(Top View)
60 o
FIG. 9
_'_lf the wall sleeve already has a rear grille, skip
to step 4. If the wall sleeve does not have a rear
grille or Iouvered panel, install the plastic grille
from the kit. Cut the plastic grille to 25-1/2" wide
and 15-1/4" high. Place the plastic grille to the
inside of the wall sleeve at the rear flange.
L_ Remove the backing from the Vertical Insulation
strip 158/16X13/8X 13/8 and attach that to the
inside right of the sleeve as shown below.
Remove the backing from the Around Insulation
strip 671/8x 13/8x 25/32 and attach that to the
inside front of the sleeve as shown below.
Place the plastic grille
_1 Fasten the 4 washer screws to secure the grille
to the wall sleeve. If you need plastic nuts to
mount plastic grille to the inside of the wall
sleeve, there are plastic nuts in the installation
kit. The nuts are installed from the inside of the
sleeve and are pressed into the square holes of
the rear flanges.
Fasten the screws
or
Vertical Insulation -
Indoor
91/2"
Outdoor
1
_ 6" !
FIG. 12
_ emove the metal rear grille and replace it with
the plastic rear grille.
Remove the -Plastic rear grille
metal rear (
FIG. 13
FIG. 10 [] If the depth of your existing wall sleeve is less
than or equal to 18", skip to step 7. Otherwise,
cut the baffles and the support blocks according
to length "A" in the table below.
FIG. 11
Depth"D"oftheexisting
wallsleeve(inches)
18 <D _<18-5/8
18-% <D_<19-s/4
19-3/4<D _<22
Length "A" A
(inches) _- Support
3/4 _[_ Block
1-3/4 Baffle
4 FIG. 14
-8-

PROCEDURE B
W emove the backing from the support blocks
and attach them to the inside of the wall sleeve
as shown FIG 15. Slide the baffle into slots of
the support blocks.
_/all
_/all
_ve
73/32")
Block
l_ Install the new unit into the wall sleeve.
_l Assemble trim as described in Step 6,
Procedure A.
FIG. 15
pvt_ E_o] _I
• Airconditionerscoveredin thismanualposean
excessiveweighthazard.Twoor morepeopleare
neededtomoveandinstalltheunit.
Topreventinjuryor strain,useproperliftingand
carryingtechniqueswhenmovingunit.
•Whenhandlingtheairconditioner,becarefultoavoid
cutsfromsharpmetalfinsonfrontandrearcoils.
•Makesureairconditionerdoesnotfallduring
removal.
• If unitdoesnotoperateafterinstallationcheck,tobe
surethecircuitinterrupterhasnotbeentripped.Refer
totheTroubleshootingguideforresetprocedure.
-9-

PROCEDURE C
H edirect the louvers at the back of the wall
sleeve to 60° angle as shown in the FIG 16.
The use of pliers is recommended.
73/32"
;--------&too
Rear Louvers
(Top View)
FIG. 16
_'_lf the wall sleeve already has a rear grille, skip
to step 4. If the wall sleeve does not have a rear
grille or Iouvered panel, install the plastic grille
from the kit. Cut the plastic grille to 26-1/2" wide
and 15-1/2" high. Place the plastic grille to the
inside of the wall sleeve at the rear flange.
Place the plastic grille FIG. 17
_1 Fasten the 4 washer screws to secure the grille
to the wall sleeve. If you need plastic nuts to
mount plastic grille to the inside of the wall
sleeve, there are plastic nuts in the installation
kit. The nuts are installed from the inside of the
sleeve and are pressed into the square holes of
the rear flanges.
or
Fasten the screws FIG. 18
_1 Remove the backing from the Horizontal
Insulation strip 237/32 X 13/8 X 13/18 and attach
that to the inside right of the sleeve as shown
below. Remove the backing from the Around
Insulation strip 5927/32 X 13/8x 13/8and attach
that to the inside front of the sleeve as shown
below.
Indoor Outdoor
8 1/2"
FIG. 19
_"_ If the depth of your existing sleeve is less than
or equal to 18", skip to step 7. Otherwise, cut
the baffles and the support blocks according to
Length "A" in the table below.
Depth"D"oftheexisting
wallsleeve(inches)
18 <D_<18-%
18-% <D_<19-3/4
19-3/4<D _<22
Length"A"
(inches)
3/4
1-3/4
4
-- upport
Block
_ Baffle
FIG. 20
r_ Remove the backing from the support blocks
and attach them to the inside of the wall sleeve
as shown FIG 21. Slide the baffle into slots of
the support blocks
Wall
Wall
Sleeve
73/32")
Block
FIG. 21
-10-

JV: [o ujiKo] i
PROCEDURE C
WTo achieve rearward slope for unit draining,
remove the backing from the 1113/ld' shim
strips and attach them as shown below in Fig.
23. The higher portion of shim is to be placed
in front of the rib on the base of wall sleeve.
FIG.22
16,,i 16,,iFIG. 23
•Airconditionerscoveredinthismanualposean
excessiveweighthazard.Twoor morepeopleare
neededto moveand installtheunit.
Topreventinjuryorstrain,useproperliftingand
carryingtechniqueswhenmovingunit.
•Whenhandlingtheairconditioner,becarefultoavoid
cutsfromsharpmetalfinsonfrontandrearcoils.
• Makesureairconditionerdoesnotfallduring
removal.
• Ifunitdoesnotoperateafterinstallationcheck,tobe
surethecircuitinterrupterhasnotbeentripped.Refer
totheTroubleshootingguideforresetprocedure.
_J Removethe metal rear grille and replace itwith
the plastic rear grille.
Remove the -Plastic rear grille
metal rear gl
FIG. 24
_'_ Install the new unit into the wall sleeve
_ ssemble trim as described in Step 6,
Procedure A.
-11 -

HOW AND WHY
Your room air conditioner provides the following
functions to make hot weather living more
comfortable:
• Cools and circulates room air.
• Lowers humidity by removing excess moisture.
• Filters out summertime dust, dirt, and some
airborne impurities.
The air conditioner performs these functions by
drawing room air through a filter which traps dust
and dirt particles. The air then passes over a
cooling coil which refrigerates the air and removes
excess moisture. The same air is then returned to
the room- cooler, drier, and cleaner. Moisture
removed from the room air is carried to the outside
and evaporated.
Your air conditioner is designed to be easy to
operate and to provide plenty of cooling power.
NORMAL SOUNDS FIG.25
Aside from the regular fan motor and compressor
sounds coming from your air conditioner, you will
once in a while hear a pinging sound. This is the
result of moisture being picked up from the air in the
room and thrown against the air conditioner's fan.
This is normal and should not be cause for concern.
Also, do not be alarmed if you hear a slight hissing or
gurgling sound coming from your air conditioner after
it is off. These are normal coolant noises.
CAPACITY AND RUNNING TIME
Proper unit size is important in deciding the desired
comfort for the area you want to cool. The proper
size is determined by the number of square feet in
the area to be cooled.
Whenever the heat or humidity load is above normal
the air conditioner must run longer and more often
to keep the desired temperature you have selected.
Under heavy heat load conditions the air conditioner
may need to run constantly to keep the temperature
you want.
At times using the MED FAN setting to circulate the
room air may make it comfortable even though you
do not have the air conditioner set to cool the air.
This will decrease your cost of use.
-Fan
init Vibration
The unit may vibrate
and make noise
because of poor wall
or window
construction.
- Compressor
The modern high
You may hear air efficiency compressor
movement from the may have a high pitched
fan. hum or pulsating noise
that cycles on and off.
Condenser --
You may hear
droplets of water
hitting the condenser,
causing a pinging or
clicking sound.
FIG. 25
-12-

FEATURES
THE UNIT
6 3 7 2 8 4 5 1 FIG. 26
1. CABINET
2. HORIZONTAL AIR DEFLECTOR
(Vertical Louver)
3. VERTICAL AIR DEFLECTOR
(Horizontal Louver)
4. AIR DISCHARGE
5. FRONT GRILLE
6. INLET GRILLE (Air Intake)
7. AIR FILTER
8. VENT CONTROL
THE SLEEVE AND THE REAR GRILLE
FIG. 27
USING THE AIR CONDITIONER
_To reduce the risk of fire, electric
shock, or injury to persons, read the important
SAFETY instructions section before operating this
appliance.
To begin operating the air conditioner after
installation, follow these steps:
1. Plug in the air conditioner. (To prevent electrical
hazards, do not use an extension cord or an
adapter plug.)
2. Set the TEMP control to the coolest setting.
3. Set the MODE control at the highest COOL level.
4. Adjust the louvers for comfortable air flow.
5. Once the room has cooled, adjust the TEMP and
MODE control to the setting you find most
comfortable.
NOTE : If the air conditioner is turned off, wait 3
minutes before restarting. This allows pressure
inside the compressor to equalize. Failure to wait 3
minutes before restarting may cause inefficient
operation.
If you move the TEMP control to a warmer, then
immediately back to a cooler setting, the unit will
shut off. Wait 3 minutes before restarting.
Refer to the AIR CONDITIONER FEATURES
section for other settings.
VENT CONTROL
The Vent Control allows the air conditioner to either
recirculate inside air (CLOSE) or exhaust air to the
outside (OPEN). (FIG. 28)
• The CLOSE position is used when maximum
cooling is desired. It may also be used for air
recirculation without cooling when the air
conditioner is set in the FAN position.
• The OPEN position removes stale air from the
room and exhausts it to the outside. Fresh air is
drawn into the room through your home's normal
air passages.
• The OPEN or CLOSE position can be used with
any fan selection.
9. SLEEVE ASSEMBLY
(Including Aluminum Rear grille)
10. REAR GRILLE
(Aluminum Rear grille) PULL OPEN /PUSH CLOSE FIG. 28
-13-

CONTROL PANEL
-FAN SPEED
• Every time you push this button, it advances the setting as follows: {High _ Low_ Med_ High}
(--TIMER
- SHUT-OFF TIME
• You will usually use shut-off time while you sleep.
• If unit is running, use Timer to set number of
hours until shut-off.
• For your sleeping comfort, once Time is set, the
Temperature setting will raise 2°F after 30 min.,
and once again after another 30 min.
• Push Timer button to advance setting from 1Hour
2Hours , ... , 12Hours maximum.
- START TIME
• If unit is off, use Timer to set number of hours
before unit starts.
• Push Timer button to advance setting from 1Hour
2Hours , ... , 12Hours maximum.
REMOTE CONTROL SIGNAL
RECEIVER
TEMPERATURE SETTING
• Use this button to automatically control the
temperature of the room.
The temperature can be set within a range
of 60°F to 86°F by increments of I°F.
• The setting appears in the display.
POWER
• To turn the air conditioner ON, push this
button.
To turn the air conditioner OFF, push the
button again.
• This button takes priority over any other
button.
• When you first turn it on, the unit is in
cool mode, High fan speed, Temperature
setting at 72°F.
MODE
- Push this button to shift mode of operation from COOL _ENERGY SAVER _FAN.
- COOL:
• Fan runs continually for normal cooling operation
- ENERGY SAVER:
• The fan stops when the compressor stops cooling. Approximately every 3 minutes the fan will turn on
and the unit will check the room air temperature to determine if cooling is needed.
- FAN:
• Fan-only operation.
Whenpower is restored after an electrical power failure, the unit will begin to run at its last setting.
-14-

REMOTE CONTROL
NOTE: The Remote Control will not operate properly if strong light shines on the sensor window of the Air
Conditioner or if there are obstacles between the Remote Control and the Air Conditioner.
Every time you push button, you will hear a beep from the Air Conditioner.
POWER
•To turn the air conditioner ON, push this button. |
To turn the air conditioner OFF, push the button again. /
• This button takes priority over any other button.
• When you first turn it on, the unit is in cool mode, High fan speed,
Temperature setting at 72°F.
• Auto Restart
In the event at a power failure, the unit will run at the previous setting once
power returns.
TEMPERATURE SETTING
• Use this button to automatically control the temperature of the room.
YPower
• Temp •
The temperature can be set within a range of 60°F to 86°F by
increments of I°F.
• The setting appears in the display.
FAN SPEED
• Every time you push this button it advances the setting as follows:
(High _Low _Ned _High)
TIMER
-SHUT-OFF TIME
• You will usually use shut-off time while you sleep.
• If unit is running, use Timer to set number of hours until shut-off.
Fan Speed
Timer Mode
!
• For your sleeping comfort, once Time is set, the Temperature setting will
raise 2°F after 30 min, and once again after another 30 min.
• Push Timer button to advance setting from 1Hour , 2Hours , ...
12Hours maximum.
- START TIME
• If unit is off, use Timer to set of hours before unit starts.
• Push Timer button to advance setting from 1Hour , 2Hours , ...
12Hours maximum.
MODE
- Push this button to shift mode of operation from COOL , ENERGY SAVER _FAN.
- COOL:
• Fan runs continually for normal cooling operation
- ENERGY SAVER:
• The fan stops when the compressor stops cooling. Approximately every 3 minutes the fan will turn on
and the unit will check the room air temperature to determine if cooling is needed.
- FAN:
• Fan-only operation.
-15-

INSERTING THE REMOTE CONTROL
BATTERIES
1. Remove the cover from the back of the remote
controller.
2. Insert two batteries.
•Be sure that the (+) and (-) directions are
correct.
• Be sure that both batteries are new.
3. Reattach cover.
FIG. 29
• Do not use rechargeable batteries.
Make sure that both batteries are new.
• In order to prevent discharge, remove the batteries
from the remote control if the air conditioner is not
going to be used for an extended period of time
Keep the remote control away from extremely hot
or humid places.
To maintain optimal operation of the remote
control, the remote sensor should not be exposed
to direct sunlight.
• The remote control can be mounted on a wall
using the mountable holder.
HORIZONTAL AIR-DIRECTION
ADJUSTMENT
• The horizontal air direction is adjusted by moving
vertical louver.
• The vertical louver control levers are located in the
right and left side of the air discharge.
FIG. 31
VERTICAL AIR-DIRECTION ADJUSTMENT
• The vertical air direction is adjusted by moving the
horizontal louvers.
FIG. 30
FIG. 32
-16-

AIR FILTER CLEANING
The Air Filter will become dirty as it removes dust
from the inside air. It should be washed at least
every 2 weeks. If the Air Filter remains full of dust,
the air flow will decrease and the cooling capacity
will be reduced, possibly damaging the unit.
• Pull the inlet grille forward and pull out the air filter.
(FIG. 33)
• Wash the Air Filter under the faucet with warm
water. Be sure to shake off all the water before
replacing the filter. (FIG. 34)
FIG. 33 FIG. 34
AIR CONDITIONER CLEANING
Clean the front grille and inlet grille by wiping with a
cloth dampened in a mild detergent solution.
The cabinet may be washed with mild soap or
detergent and lukewarm water, then polished with
liquid appliance wax.
To ensure continued peak efficiency, the condenser
coils (outdoor side of the unit) should be checked
periodically and cleaned if they become clogged
with soot or dirt from the atmosphere. Brush or
vacuum exterior coils to remove debris from fins.
I
"-- I
j_;
" I/KN ......
FIG. 35
HOW TO REMOVE THE FRONT
GRILLE
• Open the inlet grille.
• Remove the screw securing the Front Grille.
• Push the grille up from the bottom and pull the top
of the grille away from the case to lift the top tabs
out of their slots.
I
FIG. 36
HOW TO REPLACE THE
FRONT GRILLE
Attach the front grille to the cabinet by inserting the
tabs on the grille into the slots on the front of the
cabinet. Push the grille in until it snaps into place.
FIG. 37
-17-

BEFORE CALLING FOR SERVICE
Check the following list to be sure a service call is really necessary. A quick reference to this manual may
help you avoid an unneeded service call.
THE AIR CONDITIONER WILL NOT OPERATE
Check if... Then...
The CurrentinterrupterDeviceistripped.
Wall plug disconnected.
House fuse blown or circuit breaker tripped.
Power is OFF.
Unit was turned offand then on too quickly.
TEMP Control set warmer than room temperature.
Press the RESET button located on the power cord plug.
If the RESET button will not stay engaged, discontinue use of the
air conditioner and contact a qualified service technician.
Push plug firmly into wall outlet.
Replace fuse with time delay type or reset circuit breaker.
Push the power button.
Set unit off and wait 3 minutes before restarting.
Set TEMP Control to a lower number.
AIR FROM UNIT DOES NOT FEEL COLD ENOUGH.
Check if... Then...
FANSPEEDsetat LOW. PushFANSPEEDbuttontosetatHI.
TEMPControlsettoowarm. SetTEMPControltoalowertemperature.
Roomtemperaturebelow70°F(21°C). Coolingmaynotoccuruntilroomtemperaturerisesabove70°F (21°C).
Temperaturesensingtubetouchingevaporatorcoil, Straightentubeawayfromevaporatorcoil.
locatedbehindfrontgrille.
THEAIRCONDITIONERCOOLING,BUTROOMISTOOWARM- ICEFORMINGONCOOLINGCOILBEHINDINLETGRILLE.
Check if... Then...
Outdoortemperaturebelow70°F(21°C). To defrostthecoil,settheMODEtoFAN,FANspeedtoHigh.
Airfiltermaybedirty. Cleanairfilter.RefertoMaintenancesectionofowner'smanual.
Todefrostthecoil,settheMODEtoCool,Fanspeedtohigh,andthe
TEMPControlsettoolow. Tempcontroltoa highertemperature.
THEAIRCONDITIONERCOOLING,BUTROOMISTOOWARM
Check if... Then...
Dirtyairfilter- airrestricted. Cleanairfilter.RefertoMaintenancesectionofowner'smanual.
TEMPControlsettoowarm. SetTEMPControltoalowertemperature.
Frontofunitisblockedbydrapes,blinds,furniture,etc. Clearblockageinfrontofunit.
Airdistributionisrestricted.
Doors,windows,registers,etc.open.Coldairescapes. Closedoors,windows,registers,etc.
Unitrecentlyturnedoninhotroom. Allowadditionaltimetoremovestoredheatfromwalls,ceiling,floor,andfurniture.
THE AIR CONDITIONER TURNS ON AND OFF RAPIDLY.
Check if... Then...
Outsidetemperatureisextremelyhot. SetFANSPEEDonHItominimizethecoolingload.
Unitissettoenergysavermode. Approximatelyevery3minutesthefanwillturnonandthe unitwillcheck
theroomairtemperaturetodetermineifcoolingisneeded.Thisis
normalenergysavermodeoperation.
NOISE WHEN UNIT IS COOLING.
Check if... Then...
Soundoffanhittingwater-from themoistureremovalsystem. Thisisnormalwhenhumidityishigh.Closedoors,windows,andregisters.
Windowvibration- poorinstallation. Referto nsta aton nstructonsorcheckwth nsta er.
WATER DRIPPING INSIDE ROOM WHEN UNIT IS COOLING.
Check if... Then...
Theairconditionerisimproperlyinstalled. Tiltairconditionerslightlytotheoutsidetoallowwaterdrainage.Referto
installationinstructionsorcheckwithinstaller.
WATER DRIPPING OUTSIDE WHEN UNIT IS COOLING.
Check if... Then...
Theunitisremovinglargequantitiesofmoisture Thisisnormalduringexcessivelyhumiddays.
fromhumidroom.
-18-

-19-

CONTENIDO ...........................................20
GARANTIA ..............................................20
SEGURIDAD ..........................................21
Instrucciones importantes de seguridad ...21
REQUlSlTOS ELECTRICOS .............22
INSTALAClON ........................................23
Requisitos de instalaci6n ....................... 23
Instalaci6n .............................................. 24
Procedimiento A ..................................... 25
Procedimiento B..................................... 26
Procedimiento C ..................................... 28
FUNCIONAMIENTO ............................30
C6mo y por qu_ ...................................... 30
Ruidos normales .................................... 30
Capacidad y tiempo de ejecuci6n .......... 30
Caracteristicas ....................................... 31
Uso del aire acondicionado .................... 31
Panel de control ..................................... 32
Mando a distancia .................................. 33
MANTENIMIENTO ................................35
Limpieza del filtro de aire ....................... 35
Limpieza del aire acondicionado ............ 35
C6mo desmontar la rejilla frontal ........... 35
C6mo sustituir la rejilla frontal ................ 35
SOLUClON DE AVERIAS .................. 36
Antes de solicitar el servicio
de reparaci6n ......................................... 36
ACUERDOS PRINCIPALES DE
PROTECCION ........................................39
NUMEROS DE SERVICl0 .........Cubiertatrasera
GARANTIA COMPLETA DE UN ANO EN
EL AIRE ACONDICIONADO A TRAVES
DE PARED
Durante un afio a partir de la fecha de compra,
cuando este aire acondicionado funcione y se
mantenga para el enfriamiento normal seg0n las
instrucciones en el manual del propietario, Sears
reparar& este aire acondicionado, gratuitamente, si
existen defectos en el material o la mano de obra.
GARANTIA COMPLETA DE CINCO
ANOS EN EL SISTEMA SELLADO DE
REFRIGERACION
Durante cinco afios a partir de la fecha de compra,
cuando este aire acondicionado funcione y se
mantenga para el enfriamiento normal seg0n las
instrucciones en el manual del propietario, Sears
reparar& el sistema de sellado refrigeraci6n (que
consiste en refrigerante, tuberias de conexi6n, y
compresor), gratuitamente, si existen defectos en el
material o la mano de obra.
EL SERVIClO DE GARANT|A ESTA
DISPONIBLE ENTRANDO EN CONTACTO
CON EL SERVlClO DE SEARS EN EL
1-800-4-MY-HOME ®.
La cobertura de la garantia se aplica t_nicamente a
los aires acondicionaos utilizados con prop6sitos no
comerciales, dom_sticos privados.
Esta garantia se aplica t_nicamente mientras este
producto se encuentre en uso en los Estados
Unidos.
Esta garantia le da derechos legales especMcos, y
tambi_n puede tener otros derechos que varien de
estado a estado.
Distributed by Sears, Roebuck and
Co., Hoffman Estates, IL 60179
- 20 -