Kennedy Q-TORQ MW80 User manual

© The Kennedy Group Ltd. 04/02
AVAILABLE FROM YOUR DISTRIBUTOR
Foot Kilo-gram Newton Newton Foot Kilo-gram Kilo-gram Newton Foot
Pounds Metres Metres Metres Pounds Meters Meters Meters Pounds
(ft. lbs) (Kgm or (Nm) (Nm) (ft.lbs) (Kgm or (Kgm or (Nm) (ft. lbs)
mkp) mkp) mkp)
5.00 0.69 6.78 10.00 7.38 1.02 1.00 9.81 7.23
10.00 1.38 13.56 20.00 14.75 2.04 2.00 19.61 14.47
15.00 2.07 20.34 30.00 22.13 3.06 3.00 29.42 21.70
20.00 2.76 27.12 40.00 29.50 4.08 4.00 39.23 28.93
25.00 3.46 33.90 50.00 36.88 5.10 5.00 49.04 36.17
30.00 4.15 40.68 60.00 44.26 6.12 6.00 58.84 43.40
35.00 4.84 47.46 70.00 51.63 7.14 7.00 68.65 50.63
40.00 5.53 54.24 80.00 59.01 8.16 8.00 78.46 47.87
45.00 6.22 61.02 90.00 66.38 9.18 9.00 88.26 65.10
50.00 6.91 67.80 100.00 73.76 10.20 10.00 98.07 72.33
55.00 7.60 74.58 110.00 81.14 11.22 11.00 107.88 79.57
60.00 8.29 81.36 120.00 88.51 12.24 12.00 117.68 86.80
65.00 8.98 88.14 130.00 95.89 13.26 13.00 127.49 94.03
70.00 9.67 94.92 140.00 103.26 14.28 14.00 137.30 101.27
75.00 10.37 101.70 150.00 110.64 15.30 15.00 147.11 108.50
80.00 11.06 108.48 160.00 118.02 16.32 16.00 156.91 115.74
85.00 11.75 115.26 170.00 125.39 17.34 17.00 166.72 122.97
90.00 12.44 122.04 180.00 132.77 18.36 18.00 176.53 130.20
95.00 13.13 128.82 190.00 140.14 19.38 19.00 186.33 137.43
100.00 13.82 135.60 200.00 147.52 20.40 20.00 196.14 144.67
105.00 14.51 142.38 210.00 154.90 21.42 21.00 205.95 151.90
110.00 15.20 149.16 220.00 162.27 22.44 22.00 215.75 159.13
115.00 15.89 155.94 230.00 169.65 22.46 23.00 225.37 166.37
120.00 16.58 162.72 240.00 177.02 24.48 24.00 235.37 173.60
125.00 17.28 169.50 250.00 184.40 25.50 25.00 245.18 180.84
130.00 17.97 176.28 260.00 191.78 26.52 26.00 254.98 188.08
135.00 18.66 183.06 270.00 199.15 27.54 27.00 264.79 195.30
140.00 19.35 189.84 280.00 206.53 28.56 28.00 274.60 202.54
145.00 20.04 196.62 290.00 213.91 29.58 29.00 284.41 209.77
150.00 20.73 203.40 300.00 221.29 30.60 30.00 294.22 217.00
155.00 21.42 210.18 310.00 228.67 31.62 31.00 304.03 224.23
160.00 22.11 216.96 320.00 236.05 32.64 32.00 313.84 231.46
165.00 22.80 223.74 330.00 243.43 33.66 33.00 323.65 238.69
170.00 23.49 230.52 340.00 250.81 34.68 34.00 333.46 245.92
175.00 24.19 237.70 350.00 258.30 35.70 35.00 343.35 253.05
180.00 24.88 244.08 360.00 265.68 36.72 36.00 353.16 260.28
185.00 25.57 250.86 370.00 273.06 37.74 37.00 362.97 267.51
190.00 26.26 257.64 380.00 280.44 38.76 38.00 372.78 274.74
195.00 26.59 264.42 390.00 287.82 39.78 39.00 382.59 281.97
200.00 27.64 271.20 400.00 295.20 40.80 40.00 392.40 289.20
205.00 28.33 277.98 410.00 302.58 41.82 41.00 402.21 296.43
210.00 29.02 284.76
215.00 29.71 291.54
220.00 30.40 298.32
225.00 31.09 305.10
230.00 31.78 311.88
235.00 32.47 318.66
240.00 33.16 325.44
245.00 33.85 332.22
250.00 34.54 339.00
260.00 35.88 352.56
270.00 37.26 366.12
280.00 38.64 379.68
290.00 40.02 393.24
300.00 41.40 406.80
CONVERSION TABLE
OPERATORS MANUAL
DIAL INDICATING
TORQUE WRENCHES
Made in England
MW80 KEN-555-2080K MW200 KEN-555-2200K
KENNEDY TOOLS
Wigston Works, Leicester, England.

2
OPERATING INSTRUCTIONS
Restricted Access
TT = True Torque
DR = Dial Reading
E = Extension Length
L = Effective Wrench
Length
12
34
The “indicating” needle displays torque as it is
applied. The “setting” needle is used to select
and pre-set torque.If the "setting" needle has
been used to pre-set torque, the operator must
apply torque until the "indicating" needle meets
the "setting needle." At this point pre-set
torque has been reached.
Indicating
Needle
Pre-set Torque Reached
Please Note: If you use your torque wrench with any kind of extension, the torque applied will be greater
than that displayed on the dial. To calculate the increase, the formula indicated fig 4 should be used.
Dimension L (=) Model No.
368mm (14.5") MW80
445mm (17.5") MW200
MW wrenches are suitable for use with special extension spanners and adaptors.
Extension adaptors enable a wide variety of end fittings to be used.
For details of extensions and adaptors please contact you local Distributor.
Fix Socket and use to tighten right handed threads. Tightening of left handed threads can be achieved
by turning the wrench over and repeating step 1.
Setting
Needle
3
Calibration
Telephone: [phone]
Fax: [phone]
Email: [email protected]
QUALITY GUARANTEE & WARRANTY
PRODUCTS carry one years manufacturers warranty.
PRODUCTS are designed & manufactured to the highest standards & specifications
Assuring the quality and performance required by all sectors of industry.
PRODUCTS are fully guaranteed against faulty materials & workmanship
Should they be found to be defective, they will either be repaired or replaced free of charge
(fair wear and tear and/or misuse excepted).
Please retain supplier invoice as proof of purchase.
All tools are supplied with a calibration certificate valid for 12 months from date of
purchase. (Please retain invoice as proof of purchase.)
Manufactured to ISO 6789: 1992.
Accuracy: = ±4% of the reading within the effective working range of the tool. *
* ISO6789: 1992 states the effective working range of the tool is from 20% to 100% of its
maximum torque value.
You have purchased a product that is designed for high performance and a long service
life. If safety and maintenance procedures are followed and the tool is used correctly it will last
for many years.
SAFETY & MAINTENANCE
Always follow instructions for assembly before operation.
Ensure your workpiece is firmly held or fixed before commencing work.
When using torque tools it is possible that fasteners may break or slip. Always stand with
both feet on the floor and avoid applying torque in awkward positions.
The drive part of the tool and any accessories should always be in line with the fastener.
Misalignment and uncontrolled movement will affect accuracy.
Only use the tool on the job that it has been designed for.
Keep the tool clean by wiping. Never dip in cleaning fluid.
Always store tools away from dirt, oil and swarf as this can damage mechanisms.
We recommend that your torque tool be calibrated annually.