KFI UTV-DRS-K User manual
UTV DASH MOUNTED
ROCKER SWITCH KIT
721 Sata Drive
Spring Valley, MN 55975
USA /1-877-346-2050
www.kproducts.com
Important Safety Instructions
are included in this manual.
MODEL NUMBER
– Used to power the rope
in or out of your winch drum. This switch
is a Double Pull/Double Throw (two
contact points per IN or OUT)
– Simple and quick
wiring harness with color coded wires
to connect to most ATV/UTV Winch
Contactors
1. Most UTV’s and SxS’s have predened switch locations that are pre-scribed or marked
for mounting and require nish cut with a knife.
2. Use the cut-out dimensions shown below to cut-out the switch location If your dash
doesn’t have the pre-scribed areas.
3. Pull the plug end of the wiring harness through the hole and connect it to the rocker
switch outside the hole before inserting the switch.
Note: Insert the switch carefully, if the hole is to small trim some of the plastic.
This switch comes in two pieces for ease of installation, is not designed to come back apart
after installing.
1.
2.
This Rocker Switch Kit comes with a pre-wired plug with
harness and only requires the conection of the (4) wires at
the end to be conected to your winch’s electrical contactor/
solenoid.
– to be conected to the small GREEN wire on the Winch’s Contactor or the lead that
will run the winch direction -IN- if your contactor is wired differently than the KFI contactor.
– to be conected to the small BLACK wire on the Winch’s Contactor or the lead that
will run the winch direction -OUT- if your contactor is wired differently than the KFI contactor.
– to be conected to a power source that is HOT when the key or ignition is turned on.
– to be conected to the NEGATIVE (-) post on the contactor (typically with the Black
painted end) or grounded to the Frame.
If everything is wired correctly the switch will light up when your ignition is turned on and shut off
when you ignition is turned off. Also check to make sure IN runs the winch IN and OUT runds the
winch OUT. If the winch runs the opposite direction switch around the small GREEN and BLACK
wires to correct the issue.
– Power to Switch (+) (Connect to RED wire on contactor)
- #8 and #10 are for ignition power to LED’s
– Signal for Winch -IN- (Connect to small GREEN wire on contactor)
– Signal for Winch -OUT- (Connect to small BLACK wire on contactor)
– Ground (-) for LED (Connect to Frame ground or Battery (-) NEGATIVE post
on the contactor)
Tab
KFI Products
1 YEAR LIMITED WARRANTY
Kappers Fabricating, Inc. (KFI) will warranty with
a copy of your sales receipt from one of KFI’s retail
locations as proof of purchase.
Kappers Fabricating, Inc. (KFI) warrants to the
original purchaser that the mechanical and
electrical components will be free from defects
in materials and workmanship for a period of one
(1) year from the original date of purchase. We will
repair or replace, at our discretion, parts found
to be defective due to materials or workmanship.
This warranty applies only to products which have
been properly assembled, adjusted, and operated
in accordance with the instructions contained
within the product manual. This warranty does not
apply to any product of Kappers Fabricating, Inc.
that has been subject to alteration, misuse, abuse,
improper assembly or installation, or shipping
damage.
In the event you have a claim under this warranty,
contact KFI’s Technical Service and KFI will
troubleshoot any issue via phone or e-mail. If
the problem is not corrected by this method, KFI
will, at its option, authorize evaluation, repair or
replacement of the defective part or component
at a KFI Service Center. KFI will provide you with
a case number for warranty service. Please keep
it for future reference. Repairs or replacements
without prior authorization, or at an unauthorized
repair facility, will not be covered by this warranty.
This warranty does not cover the following repairs
and equipment:
This product needs periodic parts and service to
perform well. This warranty does not cover repair
when normal use has exhausted the life of a part
or the equipment as a whole.
This warranty excludes: Cosmetic defects such
as paint, decals, etc. Failures due to acts of God
and other force majeure events beyond the
manufacturer’s control. Problems cause by parts
that are not original KFI Products parts. Failures
due to Water intrusion.
THIS WARRANTY DOES NOT APPLY TO ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES
AND ANY IMPLIED WARRANTIES ARE LIMITED TO
THE SAME TIME PERIODS STATED HEREIN FOR ALL
EXPRESSED WARRANTIES.
THE WARRANTY SET FORTH ABOVE IS THE ONLY
WARRANTY. THERE ARE NO OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
Some states do not allow the exclusion of implied
warranties or the exclusion or limitation of liability
for incidental or consequential damages, or
limitations on how long an implied warranty lasts,
so the above limitation or exclusion may not apply
to you. This warranty gives you specic legal rights.
You may also have other rights that vary from state
to state.
KFI Products
Customer Service
721 Sata Drive
Spring Valley, MN 55975
www.kproducts.com
Mon – Thu, 8:00 AM – 5:00 PM (CST)
Fri, 8:00 AM - 1:00 PM (CST)
Toll Free: 1-877-346-2050
tech@kproducts.com
Note: Before installing make sure you have
the correct orientation for the switch with
the tab facing towards you.
1. Insert the blue diodes (A) rst and small
spring (B) second into the designated hole
on each side shown in Figure 1.
2. Insert the two large springs (C) into the
designated holes on each side shown in
Figure 1.
3. Set the clips (D) Face up into the
designated location shown in Figure 1.
4. Set the white rocker plunger onto the post
in the top portion of the switch shown in
Figure 2.
5. Take the top portion of the switch and
set it on the bottom portion. Shown in
Figure 3.
6. Note: The “In” position is lined up with the
(Tab) on the one side of the switch so
you know how to attach it back together
correctly. Shown in Figure 3.
7. There is a clip on each side of the rocker
switch. Push the top portion of the switch
down and snap the clips into place.
Shown in Figure 3.
Plunger
Bottom
Clip Tab
Top
Note
A
CB
D
Face Up
Tab
A
CB
Figure 2
Figure 1
Figure 3
1-877-346-2050
KFI Products
P.O. Box 32
721 Sata Drive
Spring Valley, MN 55975 USA
www.kproducts.com
Made In China
©2016 Kappers Fabricating, Inc.
Table of contents
Other KFI Automobile Accessories manuals
