Kichler Lighting Eads 310135 User manual

Includes our new
CoolTouch Control System
Looks permanent, but goes wherever you go!
U.S. Patent Pending
TM
Kichler®Lighting
7711 East Pleasant Valley Road
P.O. Box 318010
Cleveland, Ohio 44131-8010
Customer Service
866.558.5706
8:30 AM to 5:00 PM EST,
Monday - Friday
Instruction Manual
EadsTM
A Kichler
®
Decor
™
ceiling fan
310135
3066708

1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local
electrical codes. Electrical installation
should be performed by a qualified
licensed electrician.
3. WARNING: Suitable for use with solid-
state speed controls.
4. WARNING: To reduce the risk of personal
injury, use only the two steel screws (and
lock washers) provided with the outlet box
for mounting to the outlet box. Most outlet
boxes commonly used for the support of
lighting fixtures are not acceptable for fan
support and may need to be replaced,
consult a qualified electrician if in doubt.
5. WARNING: To reduce the risk of fire,
electric shock, or Personal Injury, mount
directly to a structural framing member or
to an outlet box marked 'Acceptable for
Fan Support of 15.9 kg (35 lbs) or less'. For
outlet box mounting, use mounting screws
provided with the outlet box.
6. The fan must be mounted with a minimum
of 7 feet clearance from the trailing edge of
the blades to the floor.
7. To operate the reverse function on this
fan, press the reverse button while the fan
is running.
8. Avoid placing objects in the path of the
blades.
9. To avoid personal injury or damage to the
fan and other items, be cautious when
working around or cleaning the fan.
10. Do not use water or detergents when
cleaning the fan or fan blades. A dry dust
cloth or lightly dampened cloth will be
suitable for most cleaning.
11. After making the electrical connections,
spliced conductors should be turned
upward and pushed carefully up into
outlet box. The wires should be spread
apart with the ground wire and white
(common) wire to one side with the black
(load) wire to the other side of the outlet
box.
12. Electrical diagrams are reference only.
Light kits that are not packed with the fan
must be ETL Listed and marked suitable
for use with the model fan you are
installing. Switches must be ETL General
Use Switches. Refer to the Instructions
packaged with the light kits and switches
for proper assembly.
WARNING
TO REDUCE THE RISK OF PERSONAL
INJURY, DO NOT BEND THE BLADE
BRACKETS (ALSO REFERRED TO AS
FLANGES) DURING ASSEMBLY OR AFTER
INSTALLATION. DO NOT INSERT OBJECTS
IN THE PATH OF THE BLADES.
1
1. SAFETY RULES
Special Notice
This appliance is equipped with a "Wattage
Limiting Device" required by the United
States Department of Energy. The device
has been installed at the factory and can
not be removed.
Installing Lamps in excess of 190 total
watts will disable the unit's light fixture. If
this should happen, you will need to reset
the lighting fixture by turning the power off
to the ceiling fan and/or light fixture,
reinstalling lamps totaling less that 190
watts and then turning the power back on.
WARNING
To reduce the risk of fire, electric shock, or
Personal Injury, mount directly to a structural
framing member or to an outlet box marked
'Acceptable for Fan Support of 15.9 kg(35 lbs)
or less'. For outlet box mounting, use mounting
screws provided with the outlet box.

2
3. PACKAGE CONTENTS
Unpack your fan and check the contents .
You should have the following items:
Philips screw driver
Blade screw driver
11 mm wrench
Step ladder
Wire cutters
2. TOOLS AND MATERIALS REQUIRED
EadsTM
K
A
B
C
D
E
F
G
H
I
J
L
A. Mounting Bracket (1)
B. Ball / Downrod Assembly (1)
C. Canopy (1)
D. Canopy Hole Cover (1)
E. Coupling Cover (1)
F. Motor Body (1)
G. Blade Arm (4)
H. Fan Blades (4)
I. Switch Housing (1)
J. Switch Cover (1)
K. Fob (1)
L. Package Hardware
1) Mounting Hardware:
a. wood screws (2), screws (2), flat washers (2),
lockwashers (2), wire connectors (3)
2) Blade Attachment Hardware:
a. screws (14), fiber washers (14)
3) Blade Arm Hardware:
a. screw (2)
4) Safety Cable Hardware:
a. wood screw (1), spring washer (1),
flat washer (1)
5) Balance Kit (1)
6) Screw Hardware:
a. screws (3)

4. MOUNTING OPTIONS
Outlet box
Provide strong
support
Recessed
outlet box Ceiling
mounting
plate
Outlet box
Fig. 1
Fig. 3
Fig. 4
Outlet box
Fig. 2
ANGLED CEILING
MAXIMUM 30°ANGLE
3
If there isn't an existing ETL listed mounting
box, then read the following instructions.
Disconnect the power by removing fuses or
turning off circuit breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 50 lbs). Do
not use plastic outlet boxes.
Figures 1, 2 and 3 are examples of different
ways to mount the outlet box.
NOTE: If you are installing the ceiling fan on a
sloped (vaulted) ceiling, you may need a
longer downrod to maintain proper clearance
between the tip of the blade and the ceiling.
A minimum clearance of 12" is suggested for
optimal operation.
NOTE: Depending on the location you have
selected for installation, you may need to
purchase and install a "Joist Hanger" for the
support of the outlet box. Make sure the joist
hanger you purchase has been designed for
use with ceiling fans. (Fig. 4)

4
5. HANGING THE FAN
REMEMBER to turn off the power before you
begin installation. This is necessary for your
safety and also the proper programming of the
control system.
To properly install your ceiling fan, follow the
steps below.
Step 1. Before attaching fan to outlet box
(not included), ensure the outlet box is securely
fastened to at least two points to a structural
ceiling member (a loose box will cause the fan
to wobble). Pass the 120 volt supply wires from
the ceiling outlet box through the center of the
ceiling mounting bracket. Install mounting
bracket to outlet box in ceiling using the screws
and washers included with the outlet box or
screws and washers in the hardware bag.
(Fig. 5)
Step 4. Slip the coupling cover, canopy hole cover
and canopy onto the downrod. Carefully reinstall
the hanger ball onto the downrod . Make sure the
cross pin is in the correct position and the set
screws are tight and the wires are not twisted .
( Fig. 8)
Step 2. Remove the hanger ball from downrod
assembly by loosening set screws , removing
the cross pin, and twisting ball out of the rod.
( Fig. 6)
Step 3. Loosen the two set screws and remove
the clip and cross pin from the top coupling of
the motor body.
Carefully feed the fan wires up through the
downrod. Thread the downrod onto the motor
coupling until the cross pin holes are aligned.
Next, replace the cross pin and clip, and tighten
both set screws. (Fig. 7)
EadsTM
Fig. 7
Motor Body
Cross Pin
Clip
Set Screw
Clip
Set Screw
Cross Pin
Fig. 8
Canopy
Hanger Ball
Canopy Hole Cover
Coupling Cover
Motor Body
Fig. 6
Downrod
Cross Pin Set Screw
Hanger Ball
Fig. 5
ETL Listed Outlet Box
Ceiling Mounting Bracket
Flat Washer
Screw

5
Step 5. Now lift the motor body into position
and place the hanger ball into the hanger bracket.
Rotate until the "Check Tab" has dropped into
the "Registration Slot " and seats firmly. ( Fig. 9)
The entire motor body should not rotate is this is
done correctly.
6 . INSTALLATION OF SAFETY SUPPORT
(required for Canadian installation ONLY)
WARNING: Failure to properly seat the "Check
Tab" can damage the ceiling fan during operation.
A safety support cable is provided to help prevent
the ceiling fan from failing, please install it as
follows.
Step 1. Drive a wood screw and washers into the
side of the brace that holds the outlet box. Leave
3mm (1/8") of space between the support brace
and the washer. (Fig. 10)
NOTE: Although the safety support cable is
required for Canadian installations only. It’s a good
idea to make the attachment with any installation.
Step 2. Insert the safety cable through the
mounting bracket and one of the holes in the
outlet box into the ceiling. Adjust the length of the
safety cable to reach the screw and washers by
pulling the extra cable through the cable clamp
until the overall lenght is correct, put the end of the
cable back through the cabel clamp, forming a
loop at the end of the cable. Tighten the cable
clamp securely. Now, put the loop in the end of the
safety cabel over the wood screw and under the
washer. Tighten the wood screw securely. (Fig. 11)
Fig. 9
Safety Cable Bolt
Wood Screw
Fig. 11
Fig. 10
Flat Washer
Wood Screw
Spring Washer
Outlet Box
Support Brace
Ceiling
Check Tab
Registration Slot

6
7. MAKE THE ELECTRIC CONNECTIONS
WARNING: To avoid possible electrical shock,
be sure you have turned off the power at the
main circuit panel before wiring.
WARNING: If your house wires are different
colors than referenced in this manual, stop
immediately. A professional electrician is
recommended to determine proper wiring.
Step1. Connect the fan supply BLACK wire
and fan light supply BLUE wire to the BLACK
household supply wire as shown in Fig. 12.
Step 2. Connect the fan neutral WHITE wire to
the household neutral WHITE wire as shown in
Fig. 12.
Step 3. Connect GROUND (GREEN) wires from
mounting bracket and downrod ball, to GROUND
(GREEN) or BARE (COPPER) from house.
(Fig. 12)
Follow the steps below to connect the fan to
your household wiring. Use the wire
connecting nuts supplied with your fan. Secure
the connector with electrical tape. Make sure
there are no loose wire stands or connections.
EadsTM
Fig. 12
BLACK
BLUE
WHITE
GROUND
WHITE
BLACK
Step 4. After making all of the above connecting,
spread them apart so the GREEN and WHITE
wires to one side of the outlet box and the
BLACK wire toward the other side.

7
Step 1. Remove one of the two shoulder screws
in the mounting bracket. Loosen the second
shoulder screw without fully removing it.
(Fig. 13)
Step 2. Assemble canopy by rotating key slot in
canopy over shoulder screw in mounting bracket.
Tighten shoulder screw. Fully assemble and
tighten second shoulder screw that was
previously removed. (Fig. 14)
8 . FINISHING THE INSTALLATION
Fig. 13
Fig. 14
Mounting Bracket
Shoulder Screw
Canopy
Shoulder Screw
Step 3. Securely attach and tighten the canopy
hole cover over the shoulder screws in the
mounting bracket utilizing the keyslot twist-lock
feature. (Fig. 15)
Fig. 15
Canopy Hole Cover
Shoulder Screw

8
EadsTM
9. ATTACHING THE FAN BLADES
NOTE: Before continuing , make sure the power
is disconnected by turning off the circuit breaker
of removing the fuse at the circuit box.
Step 1. Position the blade over the blade arm
with threaded posts showing. Make sure the
bottom edge of the blade is fully seated against
the blade arm. With a Philips screwdriver, start a
screw into the blade arm (do not tighten) and
repeat for the 2 remaining blade screws and fiber
washers. Tighten each screw securely starting
with the center screw. Make sure the blade is
straight. Repeat steps for the remaining blades.
(Fig. 16)
Step 2. Remove the shipping blocks from the
bottom of the motor body and discard. Fasten
blade assembly to the holes located on the
bottom of the flywheel. Tighten the two "pre-
installed" motor screws in the blade arm.
Repeat steps for the remaining blades
assemblies. (Fig. 17)
Fig. 16
Fig. 17
10. INSTALLING THE SWITCH HOUSING
Step 1. Remove the screw nearest the red dot
label on the mounting ring and loosen the other
two (do not remove). Let the 9-pin connector from
motor body through the middle hole of switch
housing. Align the two slot holes on the switch
housing over the 2 screws previously loosened
from the mounting ring. Turn the switch housing
until it locks in place at the narrow end of the key
holes. Securely tighten all three screws. (Fig. 18)
Fig. 18
Blade Screw
Fiber Washer
Blade
Blade Arm
Switch Housing
Adapter Plate
Screw
Shipping Block
Motor Body
Blade Assembly

9
11. INSTALLING THE SWITCH COVER
NOTE: Before continuing, make sure the power
is disconnected by turning off the circuit breaker
of removing the fuse at the circuit box.
NOTE: If you plan to install an “Optional” light
fixture purchased separately, please skip to
step 13 and continue. If you want your ceiling fan
installed WITHOUT an “Optional” light fixture,
follow steps below.
Step1. Remove 1 of the 3 screws on the edge of
switch housing and loosen the other 2 screws
(do not remove). (Fig. 19)
Step 2. The Square plastic wiring connector
from the motor body and switch cover will only
fit together one way. Match up the color on the
side of each connector, then push them together
until the snap engages. (Fig. 19)
Step 3. Tuck the new connections neatly into the
switch cover. Align the key holes on the switch
cover with the 2 screws on the edge of the
switch housing. Turn switch cover until it locks in
place at the narrow end of the key holes. Tighten
the 2 screws and reinstall the third screw, making
sure all three screws are tight and secure.
(Fig. 19)
Fig. 19
Fig. 20
12. INSTALLING THE FOB
Step 1. Attach the decorative pull chain fob to
the chain coming out of the switch cover. Refer
to Fig. 20.
Switch Housing
Screw
Switch Cover
Fob