Kichler Lighting Ried 300356 User manual

56" Ried
INSTRUCTION MANUAL
Model#300356
READ AND SAVE THESE INSTRUCTIONS

3
4
4
5
6
8
9
10 INFORMATIONMOTOR
11
12
13THE
15
16
16
2 KICHLER.COM

1. CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker
panel or main fusebox before starting and during
the installation.
2. WARNING: This fixture is intended for installation
in accordance with the National Electrical Code
(NEC) and all local code specifications. If you are
not familiar with code requirements, installation by
a certified electrician is recommended.
3. WARNING: To reduce the risk of fire or electric
shock, use only the control provided with the fan.
4. WARNING: To reduce the risk of fire, electric
shock, or Personal Injury, mount directly to a
structural framing member or to an outlet box
marked “Acceptable for Fan Support of 15.9 kg
(35 lbs) or less.” For outlet box mounting, use
mounting screws provided with the outlet box.
5. WARNING: The outlet box and support structure
must be securely mounted and capable of reliably
supporting a minimum of 15.9 kg (35 lbs). Use
only cULus Listed outlet boxes marked “FOR FAN
SUPPORT”.
6. WARNING: To operate the reverse function on
this fan, slide the reverse switch to the opposite
position. Do not operate reversing switch while fan
blades stopped before reversing blade direction.
7. Avoid placing objects in the path of the blades.
8. To avoid personal injury or damage to the fan and
other items, be cautious when working around or
cleaning the fan.
9. Make sure the installation site you choose allows a
minimum clearance of 2.1 m (7 feet) from the blades
to the floor and at least 30 inches from the ends of the
blades to any obstruction.
10. WARNING: make sure the power is disconnected before
cleaning your fan.
11. Do not use water or detergents when cleaning the fan
or fan blades. A dry dust cloth or lightly dampened cloth
will be suitable for most cleaning.
12. After making the electrical connections, spliced
conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread
apart with the ground wire and white (common) wire to
one side with the black (load) wire to the other side of
the outlet box.
13. Electrical diagrams are for reference only. Light kits
that are not packed with the fan must be ETL Listed
and marked suitable for use with the model fan you are
installing. Switches must be ETL General Use Switches.
Refer to the Instructions packaged with the light kits
and switches for proper assembly.
14. All set screws must be checked, and retightened where
necessary, before installation.
15. Total weight of fan plus any accessories packaged with
the fan: 6.5 kg (14.33 lbs)
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND
THE BLADES DURING ASSEMBLY OR AFTER INSTALLATION.
DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.
SAFETY RULES
READ AND SAVE THESE INSTRUCTIONS
56" Ried 3

6 6
4 KICHLER.COM

Secure the outlet box directly to the building structure. Use
appropriate fasteners and building materials. The outlet box
and its support must be able to fully support the full weight of
the fan (up to 35 lbs). Do not use plastic outlet boxes.
56" Ried 5

6 KICHLER.COM

56" Ried 7

8 KICHLER.COM

56" Ried 9

FINISHING THE MOTOR INSTALLATION
10 KICHLER.COM

FINISHING THE MOTOR INSTALLATION
56" Ried 11

12 KICHLER.COM

INSTALLING THE “OPTIONAL” LIGHT FIXTURE
56" Ried 13

INSTALLING THE “OPTIONAL” LIGHT FIXTURE
14 KICHLER.COM

HOT
TO 120V SOURCE
Outlet Box
Wall Control
Face Plate
TO LOAD
GROUND
GROUND WIRE
FROM CEILING
BLACK
("AC IN L")
BLACK
("TO MOTOR L")
Place the wall control to the outlet box, connect the wires with wire connectors
INSTALLING THE WALL CONTROL
All wiring must be in accordance with the National Electrical Code and local electrical codes.
Electrical installation should be performed by a qualified licensed electrician. Select a location
to install your wall control. You can replace an existing wall switch, or install the wall control on
ANY flat surface.
NOTE: SWITCH INSTALLATION MUST COMPLY WITH ALL LOCAL AND NATIONAL
ELECTRIC CODE .
Step 1.
WARNING: SHUT OFF MAIN POWER AT THE CIRCUIT BREAKER OF FUSE PANEL
BEFORE CONTINUING.
Remove the existing wall plate and the old switch from the wall outlet box.
Step 3.
Step 2.
Secure the wires connections and make sure there are no loose strands or
connections. Put wire connections back inside outlet box and secure the wall control
to outlet box with screws provided. Snug the face plate to wall control. (Fig. 29)
provided. (Fig. 29)
*Connect the lead wire (HOT) from outlet box to BLACK wire marked “AC IN L” from
wall control.
*Connect the lead wire (LOAD) from outlet box to BLACK wire marked “TO MOTOR L”
from wall control.
*Connect the GROUND wire from outlet box to the GROUND wire from wall control.
Disconnect wires. (Fig. 28)
Outlet Box Switch
Fig. 28
Fig. 27
Fig. 29
Wall Plate
INSTALLING THE “OPTIONAL” LIGHT FIXTURE
56" Ried 15

Fig. 31
4. REV switch: Controls direction, forward or reverse. (Fig. 31)
NOTE: Wait for fan to stop before reversing the direction of the blade rotation.
NOTE:Once completed, snug two face plates back to wall control.
LEARN
16 KICHLER.COM

OPERATING INSTRUCTIONS:
W
The slide switch controls directions: forward(switch left) or
reverse (switch right).
ARNING: Do not operate reversing switch while fan blades are in
blade direction.
Speed setting for warm or cool weather depends on factors such as
the room size, ceiling height, number of fans and so on.
Warm Weather Operation: Forward (counter clockwise).
you to set your air conditioner on a warmer setting without
Cool Weather Operation: Reverse (clockwise). An upward airflow
comfort.
Fig. 32
Fig. 33
56" Ried 17

ensure
noises
Ensure
18 KICHLER.COM

FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1.)This device may not cause harmful interference, and
2.)This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician or help.
56" Ried 19

© Kichler Lighting LLC. All Rights Reserved.
2021/07/23