Kichler Lighting ZEUS KLF-ZEUS-60-WHT-BN User manual

-BN

2
SAFETY RULES
READ AND SAVE THESE INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1.Proceed with caution. Read all instructions before beginning the installation. This will help you to avoid errors, which could lead to a hazard or
malfunction. Keep the instructions in case you have any questions later. Pass on the instructions to each subsequent owner or user of the
product. Ensure that any supplement to the instructions is enclosed. The manufacturer cannot be made responsible and/or liable for
personal injuries or damage to property cause by:
. incorrect installation . changes made to the product . improper use (misuse) . failure to observe these instructions.
2.Only an authorized electrician should execute the installation.
3.The installation height, i.e. the distance between the blades and the floor, should be at least 2.3 m.
4.Make sure the fan is securely fastened at the ceiling.
5.WARNING! To prevent injuries, make sure the blades are not bent and that there are no objects with in the area of rotation.
6.This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or
lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children
without supervision.
7. WARNING: If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the service agent or suitably
qualified persons.
8.Suitable for indoor use.
9.The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a sufficient strength to withstand 4 times
the weight of the ceiling fan. This fan weighs 11.29 KG.
10. Before disassembling light kit, make sure the power supply is disconnected from the main supply. Power supply can be on only after
installation is completed.
11. Do not ingest battery -- chemical burn hazard
- The remote control supplied with this product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause
severe internal burns in just 2 hours and can lead to death.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside and part of the body, seek immediate medical attention.
ELSTEADLIGHTING.COM

3
KLF-ZEUS-60-WHT-BN

4
1.) Because of the fan’s natural movement, some connections may become loose. Check support connections (including the suspension system), brackets, and blade attachments twice a year. Make sure they are secure.
2.) The replacement of parts of the safety suspension system device shall be performed by the suitably qualified persons
3.）For non-user replaceable light sources:
The light source contained in this luminaire shall only be replaced by the qualified person.The rated current of this light fixture is 0.048A, power factor is 0.98.
ELSTEADLIGHTING.COM
product

5
Unpack the product carefully and check that it is
complete and intact. It should not be used if there is any
damage to the cable, glass or electrical parts. In such a
case, contact customer service immediately.
KLF-ZEUS-60-WHT-BN
X2
X2
X2

6
ELSTEADLIGHTING.COM
Only an
authorized
electrician
should execute
installation
The distance between the fan blades and the wall should be at
least 0.6m.
The installation height, i.e. the distance between the blades and
the floor, should be at least 2.3 m.
The fixing means for
attachment to the ceiling such
as hooks or other devices shall
be fixed with a sufficient
strength to withstand 4 times
the weight of the ceiling fan.
This fan weighs 11.29 KG

KLF-ZEUS-60-WHT-BN
L
L
OR
220-240V
L N
X2
X2

8
F
ELSTEADLIGHTING.COM

9
5
4
3
1
2
B
C
D
E
KLF-ZEUS-60-WHT-BN

10
ELSTEADLIGHTING.COM
Remove one of
two screws as
required for step 7
K
Bolt on base
of ceiling
bracket
Long
groove on
"B"
Align bolt to
groove
Insert "B" into
gap

11
KLF-ZEUS-60-WHT-BN

12
ELSTEADLIGHTING.COM
X12

13
KLF-ZEUS-60-WHT-BN

10 11
14 ELSTEADLIGHTING.COM
K
Learn Switch:
If you do not want to use the code
set up by manufacturer or the fan
doesn’t work, then you will need
to use the set up procedures
listed below:
Install and restore power to the
fan, press and hold the “ Learn
Switch” for 3 seconds until the
light flashes (ON/OFF) twice and
light ON, and the fan runs at
medium speed, then the setting
process is completed.
NOTE: You must press the “Learn
Switch” within 30 seconds after
restoring power the fan.
Remark: The initial power-on
state is LIGHT ON, FAN OFF.
1 x 23A 12V
Battery
(Not Supplied)

H L
F/R
OFF
OFF
M
HIGH
H L
F/R
OFF
M
MEDIUM
H L
F/R
OFF
M
LOW
H L
F/R
OFF
M
H L
F/R
OFF
M
MIDDLE
BUTTON:
FORWARD/
REVERSE H L
F/R
OFF
M
15
KLF-ZEUS-60-WHT-BN

H L
F/R
OFF
M
H L
F/R
OFF
M
H L
F/R
OFF
M
H L
F/R
OFF
M
16
ELSTEADLIGHTING.COM
ON
OFF
ADJUST
BRIGHTNESS

17
Problem
Fan will not start.
Fan sounds noisy.
Fan wobble.
Solution
1.Check circuit fuses or breakers.
2.Check all electrical connections to insure proper contact. CAUTION: Make sure the main power is OFF
when checking any electrical connection.
3.Make sure the transmitter batteries are installed properly. Positive (+) side facing out.
4.Insure the batteries have a good charge.
1.Make sure all motor housing screws are snug.
2.Make sure the screws that attach the fan blade brackets to the motor are tight.
3.Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.
CAUTION:
4.Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this time.
5.If using an optional light kit, make sure the screws securing the glassware are tight.Make sure the light
bulbs are not touching any other component.
6.Do not connect this fan to a wall mounted variable speed control(s). They are not compatible with ceiling
fan motors or remote controls.
7.Make sure the upper canopy has a short distance from the ceiling. It should not touch the ceiling.
1.Check that all blade and blade arm screws are secure.
2.Most fan wobbling problems are caused when blade levels are unequal.Check this level by selecting a point
on the ceiling above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is
positioned for measurement. Repeat for each blade. The distance deviation should be equal within 1/8".
3.If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the
weight and possibly result in smoother operation.
TROUBLESHOOTING
Remote control
malfunction.
1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control
KLF-ZEUS-60-WHT-BN

KICHLER®
www.el st e ad li g h t i ng .com
UK HEAD OFFICE E lstead L ighting L td .
E lstead H ouse , M ill L ane , A lton , H ampshire , GU34
2QJ , UK
S ales O ffice : + 44 ( 0 ) 14 2 0 8 2 377
E mail : sales@elsteadlighting . com