Kichler Lighting Cadence User manual

#ADENCE4-
)NCLUDESOURNEW
#OOL4OUCH4-#ONTROL3YSTEM
,OOKSPERMANENTBUTGOESWHEREVERYOUGO
530ATENT0ENDING
+ICHLER,IGHTING
%AST0LEASANT6ALLEY2OAD
0/"OX
#LEVELAND/HIO
#USTOMER3ERVICE

!-TO0-%34
-ONDAY&RIDAY
$ESIGNEDTOCOORDINATEWITHAPOPULAR+ICHLER,IGHTINGCOLLECTION
)NSTRUCTION-ANUAL
KHA9090108

1
1. To reduce the risk of electric shock, insure
electricity has been turned off at the circuit
breaker or fuse box before beginning.
2. All wiring must be in accordance with the
National Electrical Code and local electrical
codes. Electrical installation should be
performed by a qualified licensed
electrician.
3. WARNING: Suitable for use with solid-
state speed controls.
4. WARNING: To reduce the risk of personal
injury, use only the two steel screws (and
lock washers) provided with the outlet box
for mounting to the outlet box. Most outlet
boxes commonly used for the support of
lighting fixtures are not acceptable for fan
support and may need to be replaced,
consult a qualified electrician if in doubt.
5. The outlet box and support structure must
be securely mounted and capable of
reliably supporting a minimum of 50
pounds. Use only CUL Listed outlet boxes
marked "FOR FAN SUPPORT".
6. The fan must be mounted with a minimum
of 7 feet clearance from the trailing edge of
the blades to the floor.
7. To operate the reverse function on this fan,
press the reverse button while the fan is
running.
8. Avoid placing objects in the path of the
blades.
9. To avoid personal injury or damage to the
fan and other items, be cautious when
working around or cleaning the fan.
10. Do not use water or detergents when
cleaning the fan or fan blades. A dry dust
cloth or lightly dampened cloth will be
suitable for most cleaning.
11. After making the electrical connections,
spliced conductors should be turned
upward and pushed carefully up into outlet
box. The wires should be spread apart with
the ground wire and white (common) wire
to one side with the black (load) wire to the
other side of the outlet box.
12. Electrical diagrams are reference only.
Light kits that are not packed with the fan
must be CUL Listed and marked suitable
for use with the model fan you are
installing. Switches must be CUL General
Use Switches. Refer to the Instructions
packaged with the light kits and switches
for proper assembly.
WARNING
/"Ê,1Ê/Ê,-Ê"Ê,]Ê/,Ê-"Ê
",Ê*,-" Ê 1,9]Ê"1 /Ê Ê/"Ê"1//Ê
"8Ê,ʸ*/Ê",Ê Ê
-1**",/¸°
WARNING
/"Ê,1Ê/Ê,-Ê"Ê*,-" Ê 1,9]Ê
"Ê "/Ê Ê/ÊÊ,/-Ê-"Ê
,,,Ê/"Ê-Ê -®Ê1, Ê--9Ê
",Ê/,Ê -//" °Ê"Ê "/Ê -,/Ê
"/-Ê Ê/Ê*/Ê"Ê/Ê-°
1. SAFETY RULES
Special Notice
This appliance is equipped with a "Wattage
Limiting Device" required by the United
States Department of Energy. The device
has been installed at the factory and can not
be removed.
Installing Lamps in excess of 190 total watts
will disable the unit's light fixture. If this
should happen, you will need to reset the
lighting fixture by turning the power off to
the ceiling fan and/or light fixture,
reinstalling lamps totaling less that 190
watts and then turning the power back on.

0!#+!'%#/.4%.43
5NPACKYOURFANANDCHECKTHECONTENTS9OU
SHOULDHAVETHEFOLLOWINGITEMS
0HILIPSSCREWDRIVER
3LOTSCREWDRIVER
MMWRENCH
3TEPLADDER
7IRECUTTERS
4//,3!.$-!4%2)!,32%15)2%$

#ADENCE 4-
M
N
AB
C
D
E
F
G
H
K
O
J
I
,
a. Ceiling Mounting Bracket (1)
b. Canopy (1)
c. Coupling Cover
d. Fan Assembly
e. Ball / Downrod Assembly (1)
& Extra Downrod (1)
f. Fan Blades (3)
g. Light Plate (1)
h. Glass Bowl (1)
i. Bottom Cap (1)
j. Blade Brackets (5)
k. Canopy Cover (1)
l. Bulb (1)
m. Cool TouchTM Control System
n. Receiver + 7 Wire Nut
o. Pats Bag Contents:
1.) Mounting hardware:
a. wire nuts (4), b. flat washers (2),
c. wood screws (2) d. screws (2)
2.) Blade attachment hardware:
a. screws (11),
b. paper washers (11)
3.) Safety cable hardware:
a. wood screw (1), b. flat washer (1),
c. washer (1)
4.) Blade bracket hardware:
a. screws (2), b. paper washer (2)


-/5.4).'/04)/.3
&IGURESANDAREEXAMPLESOFDIFFERENT
WAYSTOMOUNTTHEOUTLETBOX
./4%
./4%
)FYOUAREINSTALLINGTHECEILINGFANONA
SLOPEDVAULTEDCEILINGYOUMAYNEEDALONGER
DOWNRODTOMAINTAINPROPERCLEARANCEBETWEEN
THETIPOFTHEBLADEANDTHECEILING!MINIMUM
CLEARANCEOFISSUGGESTEDFOROPTIMALOPERATION

/UTLETBOX
0ROVIDESTRONG
SUPPORT
2ECESSED
OUTLETBOX #EILING
MOUNTING
PLATE
/UTLETBOX
&IG
&IG
&IG
/UTLETBOX
&IG
)FTHEREISNgTANEXSITING5,C5,FOR#ANADIAN
)NSTALLATIONLISTEDMOUNTINGBOXTHENREADTHE
FOLLOWINGINSTRUCTIONS$ISCONNECTTHEPOWERBY
REMOVINGFUSESORTURNINGOFFCIRCUITBREAKERS
3ECURETHEOUTLETBOXDIRECTLYTOTHEBUILDING
STRUCTURE5SEAPPROPRIATEFASTENERSANDBUILD
INGMATERIALS4HEOUTLETBOXANDITSSUPPORT
MUSTBEABLETOFULLYSUPPORTTHEMOVINGWEIGHT
OFTHEFANATLEASTLBS$ONOTUSEPLASTIC
OUTLETBOXES
$EPENDINGONTHELOCATIONYOUHAVESELECTED
FORINSTALLATIONYOUMAYNEEDTOPURCHASEANDINSTALL
A*OIST(ANGERFORTHESUPPORTOFTHEOUTLETBOX
-AKESURETHEJOISTHANGERYOUPURCHASEHASBEEN
DESIGNEDFORUSEWITHCEILINGFANS&IG

(!.').'4(%&!.
2%-%-"%2TOTURNOFFTHEPOWERBEFOREYOU
BEGIN
3TEP2EMOVETHEDECORATIVECANOPYBOTTOMCOVER
FROMTHECANOPYBYTURNINGTHECOVERCOUNTERCLOCKWISE
&IG
3TEP2EMOVETHECEILINGMOUNTINGBRACKETFROMTHE
CANOPYBYTURNINGTHECOVERCOUNTERCLOCKWISE&IG
3TEP0ASSTHEVOLTSUPPLYWIRESFROMTHECEILING
OUTLETBOXTHROUGHTHECENTEROFTHECEILINGMOUNTING
BRACKET&IG
3TEP,OOSENTHETWOSETSCREWSFROMTHE
COUPLINGONTOPOFTHEMOTORASSEMBLY&IG
3TEP#AREFULLYFEEDTHEELECTRICALLEADWIRESFROM
THEFANUPTHROUGHTHEDOWNROD4HREADTHEDOWNROD
INTOTHECOUPLINGUNTILTHEHITCHPINHOLESAREALIGNED
.EXTREPLACETHEHITCHPINANDRETAININGCLIP
4IGHTENBOTHSETSCREWS&IG
4OPROPERLYINSTALLYOURCEILINGFANFOLLOWTHESTEPSBELOW
3TEP!TTACHTHECEILINGMOUNTINGBRACKETTOTHE
OUTLETBOXUSINGTHESCREWSANDWASHERSINCLUDED
WITHTHEOUTLETBOX&IG
&IG
&IG
LISTEDELECTRIAL
BOX
-OUNTING"RACKET
SCREW
7ASHER
7ASHER
&IG
$OWNROD
-OTOR
#OUPLING
3ET3CREW
-OTOR
!SSEWBLY
(ANGER"ALL
,OCK0IN
(ITCH0IN
#ROSS0IN
3ET3CREW
#EILING-OUNTING
"RACKET
#ANOPY
#ANOPY#OVER

#ADENCE4-
&IG
3TEP2EMOVETHEHANGERBALLFROMTHEDOWNROD
ASSEMBLYBYLOOSENINGTHESETSCREWREMOVINGTHE
CROSSPINANDSLIDINGTHEBALLOFFTHEROD2EMOVE
THEHITCHPINANDRETAININGCLIPFROMTHEDOWNROD
ASSEMBLY&IG

5
Step. 8 Slip the coupling cover, canopy cover
and canopy onto the downrod.
Thread the hanger ball onto the downrod, insert
the cross pin through the downrod and tighten.
Now tighten the set screw. (Fig. 9)
Step. 9 Lift the motor assembly into position and
place the hanger ball into the ceiling mounting
bracket.
Rotate the entire assembly until the "Check Tab"
has dropped into the "Registration Slot" and
seats firmly. (Fig. 10)
The entire motor assembly should not rotate if
this is done correctly.
WARNING: Failure to properly seat the
"Check Tab" can damage the ceiling fan during
operation.
Fig. 9
Fig. 10
Ceiling
Mounting
Bracket
Registration slot
Check
Tab
Washer
Set screw
Lock Pin
Hitch Pin
Hanger Ball
Canopy
Canopy Cover Coupling Cover
Fan Assembly


#ADENCE4-
Fig. 11
7. ELECTRICAL CONNECTIONS
6. INSTALLATION OF SAFETY SUPPORT
(for Canadian Installation ONLY)
!SAFETYSUPPORTCABLEISPROVIDEDTOHELP
PREVENTTHECEILINGFANFROMFALLINGPLEASEINSTALL
ITASFOLLOWS
3TEP!TTACHTHEPROVIDEDWOODSCREWAND
WASHERTOTHECEILINGJOISTNEXTTOTHEMOUNTING
BRACKETBUTDONOTTIGHTEN&IG
3TEP!DJUSTTHELENGTHOFTHESAFETYCABLETO
REACHTHESCREWANDWASHERBYPULLINGTHEEXTRA
CABLETHROUGHTHECABLECLAMPUNTILTHEOVERALL
LENGTHISCORRECT0UTTHEENDOFTHECABLEBACK
THROUGHTHECABLECLAMPFORMINGALOOPATTHE
ENDOFTHECABLE4IGHTENTHECABLECLAMP
SECURELY.OWPUTTHELOOPINTHEENDOFTHE
SAFETYCABLEOVERTHEWOODSCREWANDUNDERTHE
WASHER4IGHTENTHEWOODSCREWSECURELY
Ceiling mounting
bracket Attach
safety cable
to ceiling joist
with screw and
washer
Fig. 12
Fig. 13
Code switch
Receiver
Ceiling
mounting
bracket
WARNING:4OAVOIDPOSSIBLEELECTRICALSHOCK
BESUREYOUHAVETURNEDOFFTHEPOWERATTHE
MAINCIRCUITPANEL
&OLLOWTHESTEPSBELOWTOCONNECTTHEFANTO
YOURHOUSEHOLDWIRING5SETHEWIRECONNECTING
NUTSSUPPLEDWITHYOURFAN3ECURETHE
CONNECTORSWITHELECTRICALTAPE-AKESURETHERE
ARENOLOOSEWIRESTRANDSORCONNECTIONS
NOTE:4HE#OOL4OUCH#ONTROL3YSTEMIS
EQUIPPEDWITHPOSSIBLEFREQUENCY
COMBINATIONSTOPREVENTINTERFERENCEFROMOR
WITHOTHERREMOTECONTROLUNITS4HEFREQUENCY
SWITCHESONYOURRECEIVERANDTRANSMITTERHAVE
BEENPRESETATTHEFACTORY0LEASERECHECKTO
MAKESURETHESWITCHESONTRANSMITTERAND
RECEIVERARESETTOTHESAMEPOSITIONANY
COMBINATIONOFSETTINGSWILLOPERATETHEFANAS
LONGASTHETRANSMITTERANDRECEIVERARESETTO
THESAMEPOSITION&IG
3TEP)NSERTTHERECEIVERINTOTHECEILING
MOUNTINGBRACKETWITHTHEFLATSIDEOFTHE
RECEIVERFACINGTHECEILING&IG
&ORBESTPERFORMANCEMAKESURETHE"LACK
!NTENNAONTHEENDOFTHERECEIVERREMAINS
EXTENDEDANDNOTTANGLEDWITHANYOFTHE
ELECTRICALWIRES

7
Fig. 14
Fig. 15
Green (Ground)
Fan Assembly
Green (Ground)
Outlet Box
White (AC in N)
Receiver
Black (TO MOTOR L)
White (TO MOTOR N)
Blue
(For Bottom Light)
Black (AC in L)
Mounting bracket
Canopy
Screw
Canopy cover
Step 2. Motor to Receiver Electrical
Connections: (Fig. 14)
Connect the black wire from the fan to the
black wire marked "TO MOTOR L" on the
receiver. Connect the white wire from the fan
to the white wire marked "TO MOTOR N" on
the receiver. Connect the blue wire from the
fan to the blue wire marked "FOR LIGHT" on
the receiver.
Step 3. Receiver to Supply Wires Electrical
Connections: (Fig. 14)
Secure each set of electrical connections with
with the plastic wire nuts provided in the parts
bag.
Step 4. Connect the ground wire (green or
bare copper) from the outlet box to the ground
wire on the ceiling mounting bracket and the
ground wire from the ceiling fan.
After making all connections, separate the
white and green wire connections to one side
and the black wire connections to the other
side of the outlet box.
Note: Fan must be installed at a maximum
distance of 30 feet from the CoolTouch™
Remote Transmitter for optimal signal
transmission between the transmitter and the
fan's receiving unit.
Step 1. Tuck all the connections neatly into
the ceiling outlet box.
MAKE SURE the Black Antenna wire on the
receiver remains free from all other wires.
Step 2. Slide the canopy up to ceiling and over
the two screws on hanger bracket. Rotate
canopy clockwise, next, while holding the
canopy with one hand, slide the canopy cover
over the screws and rotate clockwise until
tight. NOTE: Adjust the canopy screws as
necessary until the canopy and canopy cover
are snug. (Fig.15)
8. FINISHING THE INSTALLATION
Connect the black (load) wire from the ceiling
outlet box to the black wire marked "AC in L"
on the receiver. Connect the white (neutral)
wire from the ceiling outlet box to the white wire
marked "AC in N" on the receiver.

!33%-",9).'!.$!44!#().'
4(%&!.",!$%3
&IG
).34!,,!4).'4(%,)'(4+)4
3TEP-AKESURETHEBLADEISSTRAIGHTAND
TIGHTENEACHSCREWUNTILTHEWASHERIS
SLIGHTLYCOMPRESSEDANDALLTHREESCREWSARE
SECURE
3TEP!TTACHTHEBLADETOTHEBLADE
BRACKETUSINGTHESCREWSANDWASHERS
PROVIDED2EFERTO&IGASNEEDED
3TARTEACHSCREWINTOTHEBRACKET
2EPEATFORTHETWOREMAININGSCREWS
3CREW
3CREW
3CREW
PAPERWASHER
"LADE
"LADE
"LADE"RACKET
&IG
&IG
MOUNTINGPLATE
SCREW
,IGHTPLATE
!MPCONNECTER
-OUNTINGPLATE

#ADENCE4-
3TEP)NSERTTHEBLADEASSEMBLYINTOONEOF
THESLOTSONTHEBLADEBRACKETRINGALIGNTHE
MOUNTINGHOLESONTHEBLADEBRACKETRINGWITH
THEMOUNTINGHOLESONTHEINSIDEOFTHEBRACKET
RINGANDINSERTTWOMOUNTINGSCREWSAND
TIGHTENSECURELY2EPEATTHISPROCEDUREFORTHE
REMAINING4WOBLADEASSEMBLIES3EE
&IGUREASNEEDED
3TEP2EMOVEOFTHESCREWSONTHEEDGE
OFMOUNTINGPLATEANDLOOSENTHEOTHERSCREWS
DONOTREMOVE
./4%"EFORECONTINUINGMAKESURETHEPOWER
ISDISCONNECTEDBYTURNINGOFFTHECIRCUITBREAKER
OFREMOVINGTHEFUSEATTHECIRCUITBOX
3TEP4HESQUAREWININGCONNECTORFROMTHE
CEILINGFANANDTHELIGHTFIXTUREWILLONLYFIX
TOGETHERONEWAY-ATCHUPTHESAMECOLORON
THESIDEOFTHECONNECTORTHENPUSHTHEMTOGETHER
UNTILTHESNAPENGAGES&IG
3TEP4UCKTHECONNECTIONSNEATLYINTOTHE
MOUNTINGPLATE!LIGNTHEHOLESONTHE,IGHT0LATE
WITHTHESCREWHEADSONTHE-OUNTING0LATE2OTATE
THE,IGHT0LATEUNTILTHESCREWHEADSAREATTHE
NARROWENDOFTHEKEYHOLESLOTS2EPLACETHESCREW
YOUREMOVEDINTHEEMPTYHOLEANDTIGHTEN!,,
THREESCREWSSECURELY


).34!,,).'4(%,)'(4"5,"
',!33"/7,
./4%!-ETAL"OTTOM#APISPROVIDEDIFYOU
WOULDRATHERINSTALLYOURCEILINGFAN7)4(/54A
BOTTOMLIGHT3KIPTOSECTIONFORTHISPROCEDURE
3TEP)NSTALLTHEWATTLAMPINTHELAMPSOCKET
&IG
3TEP0LACETHEOPENSIDEOFTHEGLASSSHADEINSIDE
THELIGHTPLATEANDROTATECLOCKWISEUNTILTIGHT&IG
&IG
,IGHT0LATE 4AB
GLASSBOWL
INDENTATION
BULB
SOCKET
).34!,,).'4(%/04)/.!,"/44/-#!0
./4%4HISCEILINGFANISCOMPLIANTWITHTHE53
$EPARTMENTOF%NERGYSh%NERGY0OLICY!CTOFv
4HISACTREQUIRESADEVICETHATLIMITSTHETOTAL
WATTAGEOFTHEFANSLIGHTFIXTURETONOMORETHAN
WATTS"YINSTALLINGANYCOMBINATIONOFLIGHTBULBSTHAT
EXCEEDSWATTSORIFANELECTRICALSURGECAUSES
THEWATTAGETOEXCEEDWATTSTHELIGHTFIXTUREWILL
AUTOMATICALLYTURNOFF)FTHISSHOULDHAPPENYOUWILL
NEEDTORESETTHELIGHTFIXTUREBYTUMINGTHEPOWEROFF
TOTHECEILINGFANLIGHTFIXTURE2EINSTALLLAMPSTOTALING
LESSTHANWATTSANDTHENTURNTHEPOWERBACKON
./4%)FYOUCHOOSETHISOPTION$/./4INSTALLTHE
WATTLAMP
3TEP!LIGNTHE4HREADED0IPEONTHE-ETAL#AP
WITHTHEMOUNTINGHOLEINTHECENTEROFTHELIGHTPLATE
2OTATETHE-ETAL#APCLOCKWISEUNTILTIGHT
&IG
,IGHTPLATE 4HREADEDPIPE
"OTTOMCAP