Kichler Lighting Renew Select User manual

Product images may vary slightly from actual product.
52" RENEW SELECT
INSTRUCTION MANUAL
UL Model #330161
READ AND SAVE THESE INSTRUCTIONS REV 02-APR-2021

Net Weight: 8.30 kgs (18.30 lbs)
Gross weight: 9.70 kgs (21.38 lbs)

52" Renew Select | 3
SAFETY RULES
CARE AND USE INSTRUCTIONS
TOOLS AND MATERIALS REQUIRED
PACKAGE CONTENTS
MOUNTING OPTIONS
HANGING THE FAN
INSTALLATION OF SAFETY SUPPORT
ELECTRICAL CONNECTIONS
FINISHING THE MOTOR INSTALLATION
ATTACHING THE FAN BLADES
INSTALLING THE LIGHT KIT
ATTACHING THE GLASS SHADE
OPERATING INSTRUCTIONS
TROUBLESHOOTING
CEILING AND WALL FAN WARRANTY
FCC INFORMATION
TABLE OF CONTENTS
Read all instructions BEFORE assembly and USE of product
KEEP INSTRUCTIONS FOR FUTURE USE
4
5
6
6
7
10
11
12
13
14
14
15
16
17
18
19

| KICHLER.COM
4
SAFETY RULES
1. CAUTION -RISK OF SHOCK-
Disconnect Power at the main circuit breaker panel
or main fusebox before starting and during the
installation.
2. WARNING: This fixture is intended for installation in
accordance with the National Electrical Code (NEC)
and all local code specifications. If you are not familiar
with code requirements, installation by a certified
electrician is recommended.
3. WARNING: To reduce the risk of fire or electric shock,
do not use this fan with any solid-state speed control
device.
4. WARNING: To reduce the risk of fire, electric shock,
or personal Injury mount to an outlet box marked
“Acceptable For Fan Support of up to 22.7 kg (50
lbs)”. For outlet box mounting, use mounting screws
provided with the outlet box.
5. WARNING: To reduce the risk of fire, electric shock
or personal injury, mount fan to outlet box marked
“acceptable for fan support”.
6. The outlet box and support structure must be securely
mounted and capable of reliably supporting a minimum
of 50 pounds. Use only cULus Listed outlet boxes
marked “FOR FAN SUPPORT”.
7. The fan must be mounted with a minimum of 2.1 m
(7 feet) clearance from the trailing edge of the blades
to the floor.
8. WARNING: Do not operate reversing switch while fan
blades are in motion. Fan must be turned o and blades
stopped before reversing blade direction.
9. Avoid placing objects in the path of the blades.
10. To avoid personal injury or damage to the fan and other
items, be cautious when working around or cleaning
the fan.
11. WARNING: Make sure the power is disconnected
before cleaning the fan.
12. Do not use water or detergents when cleaning the fan
or fan blades. A dry dust cloth or lightly dampened
cloth will be suitable for most cleaning.
13. After marking electrical connections, spliced
conductors should be turned upward and pushed
carefully up into outlet box. The wires should be
spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the
outlet box and the ungrounded conductor on the other
side of the outlet box.
14. Electrical diagrams are reference only. Light Kits that
are not packed with the fan must be cULus Listed
and marked suitable for use with the model fan you
are installing. Switches must be cULus General Use
Switches. Refer to the Instructions packaged with the
light kits and switches for proper assembly.
15. WARNING: To reduce the risk of personal injury, do not
bend the blade brackets (also reered to as flanges)
during assembly or after installation. Do not insert
objects in the path of blades.
16. All set screws must be checked, and retightened where
necessary, before installation.

52" Renew Select | 5
CARE AND USE INSTRUCTIONS
1. Read and understand these Care and Use Instructions
and all installation instructions provided with this
fixture, both front and back, before proceeding with
assembly, installation, care and use of this fixture.
2. If you have doubts about how to install a lighting
fixture or if the fixture fails to operate correctly, please
contact a local qualified licensed electrical contractor.
3. All parts must be used as indicated in the assembly/
installation instructions. Do not substitute the
parts provided with any other parts (use authorized
replacement parts only) or use any parts which are
worn out or broken. If replacement parts are needed,
write to
Authorized Replacement Parts Distribution Department,
P.O. Box 318010, Cleveland, Ohio 44131-8010.
Failure to obey this instruction could invalidate the ETL/
UL or CSA certification for this fixture.
4. Be sure to use light bulbs with wattage no greater than
specified on this fixture. Be certain the electric current
is turned o before changing light bulbs.
5. If a green insulated wire or bare copper or silver wire is
included with this fixture be certain never to attach this
wire to the “hot” current carrying supply wire.
6. Be sure the fixture is supported by a chain only (if
fixture hangs by chain) and not by wire.
7. The hand-crafted beauty of this fixture is the
result of tasteful design, experienced engineering,
careful craftsmanship and a dedication to customer
satisfaction. You will be assured years of service and
enjoyment if you read and observe the following list of
product care suggestions:
• Be certain electric current is turned o before
cleaning.
• Clean metal components with a soft cloth,
moistened with a mild liquid soap solution. Wipe
clean and bu with a soft dry cloth. Under no
circumstances should any metal polish be used,
as its abrasive nature could damage the protective
finish placed on the metal parts.
• Wood components may be polished with a fine
furniture polish, taking care to avoid getting the
polish on the metal surfaces.
• Never wash glass shades in an automatic
dishwasher. To wash glass shades, line a sink with a
towel and fill with warm water and a mild liquid soap.
Wash glass with a soft cloth, rinse and wipe dry.

| KICHLER.COM
6
TOOLS REQUIRED
PACKAGE CONTENTS
• Philips screw driver
• Blade screw driver
• 11mm wrench
• Step ladder
• Wire cutters
Unpack your fan and check the contents. You should have the following items:
A. Fan blades (5)
B. Ceiling mounting bracket
C. Canopy decoration ring
D. Canopy
E. Canopy cover
F. Ball/downrod assembly
G. Coupler cover
H. Fan motor assembly
I. Light kit
J. Blade brackets with pre-installed
mounting screws (5)
K. Glass shade
L. Package hardware:
1) Safety cable hardware:
screw (1)
2) Gasket
3) Pull chains and fobs (1)
4) Balancing Kit
5) Blade attachment hardware:
screws (15), washers (15)
6) Plastic wire connectors (3)
B
D
F
J
L
A
H
I
E
C
G
K

52" Renew Select | 7
Outlet box
Provide strong
support
Recessed
outlet box Ceiling
mounting plate
Outlet box
Outlet box
ANGLED CEILING
MAXIMUM 22°
ANGLE
MOUNTING OPTIONS
If there is not an existing UL (cUL for Canadian Installation) listed
mounting box, then read the following instructions. Disconnect the
power by removing fuses or turning o circuit breakers.
Secure the outlet box directly to the building structure. Use
appropriate fasteners and building materials. The outlet box and its
support must be able to fully support the full weight of the fan (up
to 50 lbs). Do not use plastic outlet boxes.
Figures 1, 2, and 3 are examples of dierent ways to mount the
outlet box.
NOTE: If you are installing the ceiling fan on a sloped (vaulted)
ceiling, you may need a longer downrod to maintain proper
clearance between the tip of the blade and the ceiling. A minimum
clearance of 12” is suggested for optimal operation.
NOTE: Depending on the location you have selected for
installation, you may need to purchase and install a “Joist Hanger”
for the support of the outlet box. Make sure the joist hanger you
purchase has been designed for use with ceiling fans. (Fig. 4)
Fig. 2
Fig. 1
Fig. 3
Fig. 4

| KICHLER.COM
8
HANGING THE FAN
REMEMBER to turn o the power before you begin.
To properly install your ceiling fan, follow the steps below.
NOTE: This ceiling fan is supplied with two types of hanging
assemblies; the standard ceiling installation using the downrod with
ball and socket mounting and the “close-to-ceiling” installation. The
“close-to-ceiling” installation is recommended in rooms with less
than 8-feet ceilings or in areas where additional space is desired from
the floor to the fan blades.
cULus Listed
outlet box
Ceiling
mounting
bracket
Mounting screws
(supplied with electrical box
)
Washer
120V wires
Fig. 5

52" Renew Select | 9
HANGING THE MOTOR ASSEMBLY
Standard Ceiling Installation
Step 1. Pass the 120-volt supply wires through the center hole in the
ceiling hanger bracket as shown in Fig. 5.
Step 2. Secure the hanger bracket to the ceiling outlet box with the
screws and washers provided with your outlet box.
Step 3. Remove the hitch pin, lock pin and set screws from the top of the
motor assembly.
Step 4. Route wires exiting from the top of the fan motor through the
coupler cover, canopy cover, canopy, decoration ring and then through
the ball/downrod. (Fig. 6)
Step 5. Align the holes at the bottom of the downrod with the holes
in the collar on top of the motor housing (Fig. 6). Carefully insert the
hitch pin through the holes in the collar and downrod. Be careful not
to jam the pin against the wiring inside the downrod. Insert the locking
pin through the hole near the end of the hitch pin until it snaps into its
locked position.
Step 6. Tighten two set screws on top of the fan motor firmly. (Fig. 6)
Step 7. Place downrod ball into the hanger bracket socket. (Fig 7)
Fig. 6
Registration slotCheck tab
Locking pin
Set screws
Hitch pin
Ceiling canopy
Decoration ring
Coupler cover
Downrod
Cross pinHanger ball
Fig. 7

| KICHLER.COM
10
Fig. 7
HANGING THE MOTOR ASSEMBLY
Close-to-Ceiling Installation
Step 1. Pass the 120-volt supply wires through the center hole in the
ceiling hanger bracket as shown in Fig. 5.
Step 2. Secure the hanger bracket to the ceiling outlet box with the
screws and washers provided with your outlet box.
Step 3. Remove three of the six screws and lock washers (every
other one) from the collar of top motor (Fig. 8)
Step 4. Place the ceiling canopy with decoration ring and the
gasket over the collar at the top of the motor. Align the mounting
holes with the holes in the motor and fasten using the screws and
lock washers provided. (Fig. 8)
Step 5. Tighten the mounting screws securely.
WARNING: Failure to completely tighten the three screws in step 5
could result in fan loosening and possibly falling.
Step 6. Hang the fan on the hook of the hanger bracket. Be certain
that the canopy is fully locked into hook as shown in Fig. 9. This will
allow you to make the electrical connections.
Ceiling mountin
g
bracket
Canopy
Hook
Fig. 8
Fig. 9
Screws and Lock
washers(3 of 6 places)
Canopy
Gasket
Collar
Decoration ring