Kimo CO 110 Instruction Manual

CO transmitter
CO 110
KEY POINTS
ABS V0

- duct model: IP65
- ambient model: IP20
LCD 10 digit . Size: 50 x 17 mm
Value: 10 mm; Unit: 5 mm
for cable Ø 8 mm
maximum
138 g (ambient model); 150 g (duct model)
- Range from 0 to 500 ppm
- 0-10 V active output, power upply 24 Vac/Vdc (3-4 wire ) or 4-20 mA output, pa ive loop,
power upply from 16 to 30 Vdc (2 wire )
- ABS V0 hou ing, IP65 (depending on model), with or without di play
- “¼ turn” y tem mounting with wall-mount plate
- Hou ing with implified mounting y tem
FEATURES OF HOUSING
TECHNICAL FEATURES
 ppm
 From 0 to 500 ppm
 ±3 ppm or 3% of the mea ured value
! Electrochemical en or
"# 5 year
$ T63 = 35
$ 0.1 ppm
! Air and neutral ga
%&'$& From 0 to +50 °C. In non-conden ing condition. From 0 to 2000 m.
( From -10 to +70 °C
PART NUMBER
)**+
To order, ju t add the code to complete the part number :
,&)
- Active – 24 Vac/Vdc – 0-10 V
-Pa ive – 16/30 Vdc – 4-20 mA

) with di play
.without di play
/0)**+#)
CO tran mitter, 4-20 mA pa ive tran mitter, with di play
and duct probe
*All the accuracie indicated in thi technical data heet were tated in laboratory condition , and can be guaranteed for mea urement carried out in the ame condition , or carried out with calibration compen ation.
!
- Duct
(-ambient


90 mm
41 mm
80 mm
150 mm
46 mm 90 mm
109 mm

TECHNICAL SPECIFICATIONS
CONNECTIONS
Inactive
witch
)&, - active 0-10 V (power upply 24 Vac/Vdc ± 10%), 3-4 wire
- pa ive loop 4-20 mA (power upply 16/30 Vdc), 2 wire
- Common mode voltage <30 VAC
- maximum load : 500 Ohm (4-20 mA) / minimum load : 1 K Ohm (0-10 V)
 2 VA (0-10 V) or 0.6 VA (4-20 mA)
/1 2004/108/EC EMC ; 2006/95/EC Low Voltage ; 2011/65/EU RoHS II ; 2012/19/EU WEEE
/ Screw terminal block for cable from 0.05 to 2.5 mm2 or from 30 to 14 AWG
Carried out according to the code of good practice.
 USB-mini DIN cable
/1 Air and neutral ga
2
ELECTRICAL CONNECTIONS – as per NFC15-100 standard
Active
witch
!34!5674
V
-+
76 L
N
Power upply
24 Vac
class II
NL
12
+
5
VCO
4
GND
-
7
+
6
-
Power upply
24 Vdc
-
+

8
,
!59#,6,6
4(,,4
123
+
5
4
-
7
+
6
-
-
Power upply
24 Vdc
+
-
9,
8, 9,
+
123
+
5
4
-
7
L
6
N
-Power upply
24 Vac
class II
L
N
9,
+
For )**+# model with +#*+: – 1-
Regulator di play or
PLC/BMS
1
V
V
Regulator di play or PLC/BMS 1
Regulator di play or PLC/BMS 1
VCO
GND
Electrochemical
en or
3
Power upply
terminal block
Output terminal block
LCC-S
oftware
connection
;05
$1
Cable gland

GND VCO

For )**+# model with 8#<+– 1:
<,
Ico
57
+
6
-
Power upply
16-30 Vdc
Vdc
A
-
+
Ico
57
+
6
-
Vdc
-
<,
+
A
<,
SETTINGS AND USE OF THE TRANSMITTER
➢
!674!5352,,
,,46,4
To configure the tran mitter, un crew the 4
crew of the hou ing then open it. DIP
witche allowing the different etting are
acce ible.
1
2
3
4
... ...
... ...
Di play/regulator/PLC
1
To et a mea uring range, put the on-off witche 2, 3 and 4 a hown below :
➢
Di play/regulator/PLC
1
+-
On-off witch
Setting of
mea uring range
MOUNTING
To mount the tran mitter, mount the ABS plate on the wall (drilling : Ø6 mm, crew and pin are
upplied).
In ert the tran mitter on the fixing plate ( ee A on the drawing be ide). Rotate the hou ing in
clockwi e direction until you hear a “click” which confirm that the tran mitter i correctly in talled.
7.5
8
4.5
40
50 68
75
37.5
23.75
14
A
A
04
8054
34
16-30 Vdc
,,=
It i po ible to configure intermediary range .
Attention : the minimum difference between the minimum scale and the maximum scale is 20.
Example: for a 0-500 ppm tran mitter, the minimum delta i 20 ppm. So the tran mitter could be configure from 0
to 70 ppm from 0 to 20 ppm.
• To acce to the configuration via oftware :
- Set the witch a hown be ide.
- Connect the cable of the LCC-S to the connection of the tran mitter.
• To configure the tran mitter, plea e refer to the LCC-S u er manual.
Caution : The configuration of the parameters can be done either by DI switch, or by software (you cannot combine both solutions).
CONFIGURATION IA LCC-S SOFTWARE (optional)
1
2
3
4
(,*

 1
+>++ ;+*++ ;+<++

1
2
3
4
1
2
3
4
1
2
3
4
Off On
1
Active witch

FTang_CO110 – 03/03/15 – RCS (24) Périgueux 349 282 095 Non-contractual document – We re erve the right to modify the characteri tic of our product without prior notice.
MAINTENANCE
Plea e avoid any aggre ive olvent. Plea e protect the tran mitter and it probe from any cleaning product containing formol, that may be u ed for cleaning
room or duct .
OPTIONS AND ACCESSORIES
●?2"#*++Power upplycla 2, 230 Vac input, 24 Vac output
●?2"#*++ Power upplycla 2, 230 Vac input, 24 Vdc output
●"#( configuration oftware with USB cable
POSITIONING OF THE PROBE
For duct model , the po itioning of the probe i important to get accurate mea urement : the hole located next to the crew at the end of the probe mu t face
the air flow.
Procedure to modify the po itioning of the end of the probe:
➢Un crew the crew.
➢Turn the end of the probe: the hole mu t face the air flow.
➢Replace the crew.
Screw
End of the probe
Hole
),14
PRECAUTIONS FOR USE
Plea e alway u e the device in accordance with it intended u e and within parameter de cribed in the technical feature in order not to compromi e the
protection en ured by the device.
Once returned to KIMO, required wa te collection will be a ured in the re pect of the environment in accordance with European guideline relating to WEEE.