Kimo AQ 110 User manual

Air Quality
AQ 110
DESCRIPTION OF THE DEVICE





PERFOM A MEASUREMENT
➢Turn on the device by pressing on «».
The device displays its name «AQ110».
When it turns on, the device performs a pre-heating phase. This phase lasts 10 seconds. The count of this pre-heating time
displays on screen.
The measure probe must be left to the open-air during this pre-heating phase.
➢Put the probe to the required location.
The device displays the C 2 and temperature measurements.
FREEZE THE MEASUREMENT
During the measurement:
➢Press on «» to freeze the measurement.
«Hold» appears on the screen and the measurements are frozen.
➢Press on «» to exit the hold function.
The device returns to the measurements display.

ADJUST THE DEVICE

The device is on and displays the measurements.
➢Press on «».
«UNIT» blinks on screen.
➢Press on «».
The unit currently used blinks at the bottom of the screen.
➢Press on «» until the required unit appears : C or F.
➢Press on «» to validate.
«UNIT» blinks on screen.
➢Press on «» to return to the measurements display.

The device is on and displays the measurements.
➢Press on «» until « !""» blinks on screen.
➢Press on «», the time before device auto shut-off blinks at the bottom of the screen.
➢Press on «» to select the time before device auto shut-off: 15, 30, 45, 60, 75, 90, 105, 120 minutes or OFF.
➢Press on «» to validate.
«AUTO O » blinks on screen.
➢Press on «» to return to the measurements display.
# 
$ %
&'
P_ATM
900
hPa
( 
 
&'
UNIT
C
&'
AUTO
OFF
OFF
&'
BEEP
ON


AUTO
OFF
OFF



&'
AUTO
OFF
OFF

AUTO
OFF
15 / 30mn...
$
&'
AUTO
OFF
30mn
 
#(#)
PPm
$*')
C
●!+,
nce the measurement is frozen:
➢Press on «».
The device displays the maximum value of C ² measured since the last questioning at the top of the screen and the minimum
value of C ² measured since the last questioning at the bottom of the screen.
➢Press again on «».
The device displays the maximum value of temperature measured since the last questioning at the top of the screen and the
minimum value of temperature measured since the last questioning at the bottom of the screen.
➢Press on «» to return to the measurements display.
DISPLAY THE MINIMUM AND THE MAXIMUM


&'
UNIT
F
 UNIT
&'
C / F

# UNIT
&'
C
#(#)
PPm
--')
F


&'
UNIT
C

CHANGE THE ATTERIES
ACTIVATE THE ACKLIGHT
The device is on and displays the measurements.
➢Press on «»: to activate the backlight.
➢To deactivate it press again on «».

To have a precise and representative measurement, the atmospheric pressure of the place where the measurements are performed
must be entered in the device.
The device is on and displays the measurements.
➢Press on «» until «./!0» blinks on screen.
➢Press on «».
The first digit of the atmospheric pressure blinks on screen. The atmospheric pressure is between 800 and 1200h Pa.
➢Press on « » to select the first digit value and press on «» to validate.
The following digit blinks on screen.
➢Perform the same procedure for the following digits (press on «On/Off/Hold» to return to the previous digit).
➢Press on «» when the last digit is adjusted.
«P_ATM» blinks on screen.
➢Press on «» to return to the measurements display.
++12
The device is on and displays the measurement.
➢Press on «» until «.» blinks on screen.
➢Press on « ».
«O » or «ON» blinks on screen.
➢Press on «2» to activate the keys beep «3» or deactivate it «""».
➢Press on «» to validate.
«BEEP» blinks on screen.
➢Press on «» to return to the measurements display.
   BEEP
&'
ON
BEEP
&'
OFF / ON
#(#)
PPm
$*')
C
&'
BEEP
ON

&'
BEEP
OFF
%


➢ Remove the front part at the back of the device.
➢ Change the old batteries by AAA LR03 1.5V batteries.
➢ Replace the front part.

NTang – portable-AQ110 – 10/06/14 – RCS (24) Périgueux 349 282 095 Non-contractual document – We reserve the right to modify the characteristics of our products without prior notice.
Once returned to KIMO, required waste collection will be assured in the respect of the environment in accordance to 2002/96/CE guidelines relating to WEEE