kincrome K7561 User manual

1
Operation Manual
Parts List
12 x EVA Liners
Chest & Trolley Combo
10 Drawer Wide Body
K7561
40kg+
This product requires a two person lift
- use proper lifting techniques
Bunnings Weight Icons (2676) 30/3/04 10:11 AM Page 3
TOOL CHEST SPECIFICATIONS
Width Depth Height
Overall 902mm 315mm 475mm
Top Section 860mm 310mm 145mm
Small Drawers
Shallow 260mm 260mm 38mm
Deep 260mm 260mm 92mm
Large Drawers
Shallow 835mm 260mm 38mm
Deep 835mm 260mm 63mm
Weight 30.1kg
OVERALL SPECIFICATIONS
Width Depth Height
Overall 1020mm 460mm 1570mm
Overall (w/o
Castors)
1020mm 460mm 1415mm
Weight 80.3kg
TOOL TROLLEY SPECIFICATIONS
Width Depth Height
Overall 1020mm 460mm 1107mm
Overall (w/o
Castors)
1020mm 460mm 955mm
Top Section 930mm 455mm 17mm
Drawers
Shallow 860mm 395mm 55mm
Deep 860mm 395mm 135mm
Cabinet 935mm 438mm 555mm
Side Parts Tray 80mm 440mm 75mm
Castors 125 x 50mm (5 x 2”) 2 x Locking
Weight 50.2kg
Keys x 6
Handle x 1
Side Parts Tray x 1
Non-Locking Castors x 2
Locking Castors x 2
16 x 12mm Bolts
for Castors
Screws;
5 x Short,
5 x Long
(Screwed into
Removeable Panel)
TOOLS & ASSISTANCE NEEDED
2 People Lift 10mm Spanner
12mm Spanner or
5mm Hex Key
12mm Spanner +
Phillips Screwdriver
or
+
CastorRemoving Chest Handle
THIS OPERATING MANUAL CONTAINS IMPORTANT
SAFETY INFORMATION. READ CAREFULLY AND
UNDERSTAND ALL INFORMATION BEFORE
OPERATING STORAGE CABINET.
SAVE THIS MANUAL FOR FUTURE USE
K7561 manual.indd 1 14/05/2018 11:08 AM

Push up the
right grey release lever
Pull down the
left grey release lever
2
• Periodically tighten all hardware
• Periodically lubricate castors
• Lubricate the slides twice a year
• Lubricate the lock with graphite annually
• Use a damp Microfibre cloth to clean all surfaces
Assembly Instructions
Maintenance
2
Chest & Trolley Combo
10 Drawer Wide Body
K7561
1
2
3
4
5
6
7
8
9
10
11
11
10
REMOVE PRODUCT FROM CARTON AND STAND UNIT UPRIGHT
UNLOCK THE TROLLEY AND REMOVE THE HANDLE, CASTORS AND
SIDE PARTS TRAY FROM THE DEEP DRAWER
LOCK UNIT, THEN FLIP UNIT UPSIDE DOWN
UNLOCK CABINET, THEN OPEN CABINET DOORS. LOCATED INSIDE
IS THE CHEST, AND 4 BOLTS SECURING IT ON A WOOD PANEL
These are holding the chest down and need to be removed using a
12mm Spanner or 5mm Hex Key.
NOTE: Bolts need to be kept for castor installation further in the
process.
REMOVE THE REMOVEABLE PANEL FROM THE REAR OF THE
TROLLEY USING A PHILLIPS SCREWDRIVER.
Unscrew the 10 screws from the removeable panel. Save the screws
to reinstall the panel later. There are 5 short screws and 5 long
screws that come out. Ensure they go back in the same place.
NOTE: Short Screws at the bottom of the Panel, and longer screws
at the top.
REMOVE THE CHEST FROM THE TROLLEY FROM THE
REMOVEABLE PANEL ACCESS
WITH THE UNIT STILL UPSIDE DOWN, REINSTALL THE BACK
PANEL AND SCREWS, WITH SHORT SCREWS AT THE TOP, AND
LONGER SCREWS AT THE BOTTOM
Please refer to pictures in Step 5.
MOUNT THE CASTORS TO TROLLEY.
Ensure both Lockable Swivel Castors are located at the front of the
trolley for easy locking when in use, and tighten using a 12mm
Spanner or 5mm Hex Key.
LOCK UNIT, AND FLIP TO THE CORRECT ORIENTATION.
STANDING THE TROLLEY UPRIGHT, INSTALL THE CHEST ON TOP
OF THE TROLLEY.
INSTALL THE SIDE HANDLE AND SIDE PARTS TRAY TOGETHER.
First, place the Handle in position and hold the Side Parts Tray in
place whilst the second person screws in the bolts. This can be done
on either left or right side of the trolley and will need a 10mm
Spanner to tighten.
REMOVING THE DRAWERS
Fully extend the empty drawer. Push up the right grey release lever
while pushing down the left grey release lever. Pull the drawer
outward until it is released from the drawer slide.
RE-INSERTING THE DRAWERS
Extend the drawer slides. Insert the brackets on each side of the
drawer into the slots on the slides, being careful that they are
properly positioned. Once properly inserted, completely close the
drawer to set the slides in their proper positions.
1 3
5
6 8
Small Screw on Left,
Long Screw on Right
A
A
A B C
B
B
C
Short Screws at the bottom of
the Panel, and longer screws at
the top.
K7561 manual.indd 2 14/05/2018 11:09 AM

ITEM PART NO. DESCRIPTION QUANTITY
1 K7529-1 Chest Lock & Key X 1 1
2 K7529-2 Trolley Lock & Key X 1 1
3 K7529-3 Cabinet Lock & Key X 1 1
4 K7529-4 Key Only X 1 1
5 K7561-13 Gas Strut (1 X Piece) 2
6 K7529-6 Chest Ball Bearing Slide (Pair) 7
7K7529-7 Trolley Ball Bearing Slide (Pair) 3
8 K7561-1
Drawer Grip Small (Chest) 5
9 K7561-2 Drawer Grip Large (Chest) 2
10 K7561-3
Small Drawer (Chest) 4
11 K7561-4 Small Drawer Deep (Chest) 1
12 K7561-5 Large Drawer (Chest) 1
13 K7561-6 Large Drawer Deep (Chest) 1
14 K7529-13 Rubber Grommet (1 X Piece) 2
ITEM PART NO. DESCRIPTION QUANTITY
15 K7529-14 Side Carry Handle (Chest) 2
16 K7561-7 Eva Mat Pack (12 X Pieces) 1
17 K7529-16 Trolley Handle 1
18 K7529-17 Side Parts Tray 1
19 K7561-8 Large Drawer (Trolley) 2
20 K7561-9 Large Drawer Deep (Trolley) 1
21 K7561-10 Drawer Grip Large (Trolley) 3
22 K7561-11 Cabinet Door 2
23 K7529-22 Cabinet Hinges 4
24 K7561-12 Cabinet Grip 2
25 K7529-24 Castors Swivel (1 X Piece) 2
26 K7529-25 Castors Swivel Locking (1 X Piece) 2
27 K7529-26 Badge 1
Replacement Parts
3
1 & 4
16
5
26
24
20 & 21
7 & 19
8 & 10
2
6 & 9 & 12
15
27
14
17
11
13
18
16
17
22
25
23
3
National Head Office
National Distribution and Showroom
3 Lakeview Dve, Caribbean Business Park
Scoresby Victoria 3179 Australia
E [e-mail]
W kincrome.com.au
Administration
T+61 3 9730 7100 F+ 61 3 9730 7199
ABN 41 007 185 006
Customer Service Centre
T1300 657 528 F1300 556 005
National Head Office
National Distribution and Showroom
3 Lakeview Dve, Caribbean Business Park
Scoresby Victoria 3179 Australia
E [email protected]
W kincrome.com.au
Administration
T+61 3 9730 7100 F+ 61 3 9730 7199
ABN 41 007 185 006
Customer Service Centre
T1300 657 528 F1300 556 005
Australia & Global UK & EU
www.kincrome.com.au www.kincrome.co.uk
[e-mail] [e-mail]
Made to Kincrome Tools & Equipment Pty Ltd Global
specications and quality standards in China
Kincrome UK Ltd PO Box 646 EASTLEIGH SO50 0NA
K7561
Chest & Trolley Combo
10 Drawer Wide Body
K7561 manual.indd 3 14/05/2018 11:09 AM