KISANKRAFT KK-P767 User manual

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with KisanKraft by sending
the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Incidental / Consequential Loss: KisanKraft Limited or its manufacturers will not be liable for general
damages, including bodily injuries, or for incidental or consequential damages including, but not limited to, loss of
use, loss of profits, loss of production, expense of substitute equipment or other commercial loss or damage.
Limitation of Liability: This limited warranty is in lieu of all other express warranties, obligations, or liabilities.
Any implied warranties, obligations or liabilities, including, but not limited to, any implied warranty of
merchantability shall be limited in duration to the applicable warranty period. Any action for breach of any
warranties hereunder, including, but not limited to, any implied warranty of merchantability must be brought within
the applicable warranty period.
Modifications of Warranty: No agent, representative, dealer, or employee of KisanKraft Limited or any of
its manufacturers has the authority to increase or alter the obligations of this warranty.
Assignment / Transfer of warranty: The warranty cannot be assigned and shall not transfer if the product
is resold by the first buyer. The above warranties are extended to the first end user (original purchaser), and no
warranty is made, nor authorized to be made assignable on resale by the first end user.
What you must do to obtain limited warranty service: To obtain performance of any obligation
under this warranty for failure during the applicable warranty period, you must deliver the defective product, to the
nearest Authorized Dealer, along with proof-of-purchase (invoice/receipt). KisanKraft Limited, its manufacturers and
its dealers reserve the right to inspect the claimed defective part(s) to determine if the malfunction is the result of
a defect covered by this warranty. Please note that the decision of KisanKraft Limited with respect to any warranty
claim is final.
After-sales Service (Including Warranty): KisanKraft Limited does not sell directly to consumers. All
sales or supplies are made through Authorized Dealers. It is the responsibility of the Authorized Dealer to provide
all after-sales service to consumers. Any warranty claim should be raised by dealer to KisanKraft Limited as per
warranty policy.
Jurisdiction: All disputes are subject to Bangalore court’s jurisdiction.
Notes:
➢This purchase is not contingent upon a product demonstration. The purchaser shall satisfy himself with the
product, including any product demonstration or verification of any function, before buying. KisanKraft Limited
or its authorized dealers, including online sellers, shall not be liable to give any on-site demonstration after
purchase of any of the product.
➢Any product once used will not be taken back by KisanKraft Limited.
➢Warranty and After Sale Services (including but not limited to installation, Demonstration, Repair, Routine
Maintenance etc.), should be done through the Authorized Dealer selling this product.
➢Dealers should have their own technician to provide After Sales Services to their Customers. KisanKraft Limited
provides free training to Authorized Dealer’s technicians at KisanKraft Limited’s head office, on request from
Authorized Dealer.
KisanKraft®
Warranty Certificate
(DEALER COPY)
This warranty is null & void, if you fail to register the warranty with KisanKraft by
sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Product
Agricultural Knapsack
Sprayer (Power) /
Agricultural Portable
Sprayer (Power)
(2-Stroke)
KisanKraft
Invoice Date
Brand
KisanKraft
KisanKraft
Invoice No.
Model
KK-708, KK-708(AL-1), KK-708X, KK-707,
KK-P767, KK-P-768, KK-PPS-P769, KK-P780
KK-KPS-802, KK-KPS-162, KK KK-TPS-60T
WARRANTY
PERIOD
6-MONTHS
FOR THE SPECIFIED PERIOD FROM THE DATE OF
SALE OR DELIVERY WHICHEVER IS EARLIER.
Dealer’s
Invoice Date
Dealer’s
Invoice No.
Buyer’s Info (Name, Address, Phone, etc.):
Dealer’s Stamp (Address, Phone, TIN, etc.):
Buyer’s Sign
Dealer’s Sign
Warranty Policy
What is covered: KisanKraft Limited and its manufacturers warrant this product to be free from defects
in material or workmanship. All parts defective in material and workmanship are covered.
This warranty will only cover defects arising under normal usage.
This warranty is limited to repair or replacement by KisanKraft Limited or its manufacturers of such parts as
appear to KisanKraft or its manufacturers, upon inspection, to be defective in material and/or workmanship.
KisanKraft or its manufacturers make no warranty with respect to items not manufactured or sold by them.
No onsite warranty is provided by KisanKraft Limited or its manufacturers. Defective items must be
brought/sent to our Authorized Dealer or KisanKraft Limited’s office for service.
What is not covered: The warranty shall become null and void and neither KisanKraft Limited nor any
of its manufacturers, nor its authorized dealers assumes any responsibility, if the failure was caused by the
following:
(1) Operation of product with incorrect fuel or lubricants, (2) Incorrect usage of machine or misuse, (3) Lack
of maintenance, (4) Negligence, (5) Accident or physical damage, (6) Repairs made by unauthorized parties
and/or with unauthorized parts, (7) Improper set up, adjustments, tampering or altered products (8) Any
modification to the product what-so-ever.
Important: (1) Normal maintenance and adjustments to the product is the responsibility of the customer.
(2) Normal wear and tear are not covered under warranty. (3) Rubber/plastic parts and consumables such
as blades, clutch and clutch-bell, sparkplugs, nylon line, air-filters, fuel-filters, oil seals and gaskets etc. are
not covered under the warranty. (4) Electrical Motor, Electrical Parts, Battery Etc. are not covered under the
warranty.

KisanKraft®
Warranty Certificate
(DEALER COPY)
This warranty is null & void, if you fail to register the warranty with KisanKraft by
sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Incidental / Consequential Loss: KisanKraft Limited or its manufacturers will not be liable for
general damages, including bodily injuries, or for incidental or consequential damages including, but not
limited to, loss of use, loss of profits, loss of production, expense of substitute equipment or other
commercial loss or damage.
Limitation of Liability: This limited warranty is in lieu of all other express warranties, obligations, or
liabilities. Any implied warranties, obligations or liabilities, including, but not limited to, any implied
warranty of merchantability shall be limited in duration to the applicable warranty period. Any action for
breach of any warranties hereunder, including, but not limited to, any implied warranty of merchantability
must be brought within the applicable warranty period.
Modifications of Warranty: No agent, representative, dealer, or employee of KisanKraft Limited or
any of its manufacturers has the authority to increase or alter the obligations of this warranty.
Assignment / Transfer of warranty: The warranty cannot be assigned and shall not transfer if the
product is resold by the first buyer. The above warranties are extended to the first end user (original
purchaser), and no warranty is made, nor authorized to be made assignable on resale by the first end user.
What you must do to obtain limited warranty service: To obtain performance of any
obligation under this warranty for failure during the applicable warranty period, you must deliver the
defective product, to the nearest Authorized Dealer, along with proof-of-purchase (invoice/receipt).
KisanKraft Limited, its manufacturers and its dealers reserve the right to inspect the claimed defective
part(s) to determine if the malfunction is the result of a defect covered by this warranty. Please note that
the decision of KisanKraft Limited with respect to any warranty claim is final.
After-sales Service (Including Warranty): KisanKraft Limited does not sell directly to consumers.
All sales or supplies are made through Authorized Dealers. It is the responsibility of the Authorized Dealer
to provide all after-sales service to consumers. Any warranty claim should be raised by dealer to KisanKraft
Limited as per warranty policy.
Jurisdiction: All disputes are subject to Bangalore court’s jurisdiction.
Notes:
➢This purchase is not contingent upon a product demonstration. The purchaser shall satisfy himself with
the product, including any product demonstration or verification of any function, before buying.
KisanKraft Limited or its authorized dealers, including online sellers, shall not be liable to give any on-
site demonstration after purchase of any of the product.
➢Any product once used will not be taken back by KisanKraft Limited.
➢Warranty and After Sale Services (including but not limited to installation, Demonstration, Repair,
Routine Maintenance etc.), should be done through the Authorized Dealer selling this product.
➢Dealers should have their own technician to provide After Sales Services to their Customers. KisanKraft
Limited provides free training to Authorized Dealer’s technicians at KisanKraft Limited’s head office, on
request from Authorized Dealer.
KisanKraft®
Warranty Certificate
(KISANKRAFT COPY)
This warranty is null & void, if you fail to register the warranty with KisanKraft by sending
the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 47 of 48
Product
Agricultural Knapsack Sprayer
(Power) / Agricultural Portable
Sprayer (Power)
(2-Stroke)
KisanKraft
Invoice Date
Brand
KisanKraft
KisanKraft
Invoice No.
Model
KK-708, KK-708(AL-1), KK-708X KK-707,
KK-P767, KK-P-768, KK-PPS-P769, KK-P780
KK-KPS-802, KK-KPS-162, KK-TPS-60T
WARRANTY
PERIOD
6-Months
FOR THE SPECIFIED PERIOD FROM THE DATE OF
SALE OR DELIVERY WHICHEVER IS EARLIER.
Dealer’s Invoice
Date
Dealer’s Invoice
No.
Buyer’s Info (Name, Address, Phone, etc.):
Dealer’s Stamp (Address, Phone, TIN, etc.):
Buyer’s Sign
Dealer’s Sign
Warranty Policy
What is covered: KisanKraft Limited and its manufacturers warrant this product to be free from defects in
material or workmanship. All parts defective in material and workmanship are covered.
This warranty will only cover defects arising under normal usage.
This warranty is limited to repair or replacement by KisanKraft Limited or its manufacturers of such parts as appear
to KisanKraft or its manufacturers, upon inspection, to be defective in material and/or workmanship. KisanKraft or
its manufacturers make no warranty with respect to items not manufactured or sold by them. No onsite warranty is
provided by KisanKraft Limited or its manufacturers. Defective items must be brought/sent to our Authorized Dealer
or KisanKraft Limited’s office for service.
What is not covered: The warranty shall become null and void and neither KisanKraft Limited nor any of its
manufacturers, nor its authorized dealers assumes any responsibility, if the failure was caused by the following:
(1) Operation of product with incorrect fuel or lubricants, (2) Incorrect usage of machine or misuse, (3) Lack of
maintenance, (4) Negligence, (5) Accident or physical damage, (6) Repairs made by unauthorized parties and/or with
unauthorized parts, (7) Improper set up, adjustments, tampering or altered products (8) Any modification to the
product what-so-ever.
Important: (1) Normal maintenance and adjustments to the product is the responsibility of the customer. (2) Normal
wear and tear are not covered under warranty. (3) Rubber/plastic parts and consumables such as blades, clutch and
clutch-bell, sparkplugs, nylon line, air-filters, fuel-filters, oil seals and gaskets etc. are not covered under the
warranty. (4) Electrical Motor, Electrical Parts, Battery Etc. are not covered under the warranty.

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Wide Range of Products for Every Need
For more information give MISSED CALL: 07676065555
Many of our products have BIS: ISI certification.
KisanKraft®
Agricultural Portable Sprayer (Power)
KK- P767 / P768 / P769 / P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/AL/X, KK - KPS- 162 / 802
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 3 of 48
User Manual
KisanKraft Limited
Sri Huchhanna Tower, #4,1st Main,7-A Cross, Maruthi Layout, Dasarahalli,
HAF Post, Hebbal, Bangalore 560024,Karnataka,INDIA
♦♦Bangalore (HO) ♦Ahmedabad ♦Bhopal ♦Bhubaneswar ♦Coimbatore
♦Guwahati ♦Hubli ♦Hyderabad ♦Nellore ♦Jaipur ♦Karnal
♦Kolkata ♦Lucknow ♦Pune ♦Raipur

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
CONTENTS
BEFORE GETTING STARTED.................................................................................................. 7
SAFETY INSTRUCTIONS ........................................................................................................7
OVERVIEW OF COMPONENTS.............................................................................................. 8
ASSEMBLY............................................................................................................................9
OPERATING INSTRUCTIONS...............................................................................................10
MAINTENANCE AND STORAGE .......................................................................................... 16
TECHNICAL SPECIFICATIONS.............................................................................................. 18
TROUBLESHOOTING ..........................................................................................................19
DIAGRAM-POWER SPRAYER .............................................................................................. 21
PARTS LIST - POWER SPRAYER...........................................................................................22
PRESSURE PUMP PARTS - DIAGRAM..................................................................................24
PRESSURE PUMP PARTS-LIST.............................................................................................25
2 STROKE PETROL ENGINE- USER MANUAL.......................................................................27
PETROL ENGINE (2-STROKE)-PARTS DIAGRAM..................................................................41
PETROL ENGINE (2-STROKE)-PARTS LIST............................................................................42
KisanKraft®
PRODUCT RANGE
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 45 of 48
KisanKraft has a large range of products to serve the farmers. A list of our products
is given below:
Brush Cutters and Accessories
Brush Cutter/Power Weeder
Backpack Brush Cutter
Tea Pruner
Pole pruner with Engine
Reaper Attachment
Blades-Circular
Blades (2 &3 points)
Baffle
Nylon Rope
Tap & Go
Chainsaws
Petrol Chainsaw
Electric Chainsaw
Chain Sharpening Machine
Engines and Water Pumps
Engine –Diesel-(Horizontal)
Engine –Diesel(Vertical)
Engine-Kerosene
Water Pump withPetrol Engine
Water Pump with Kerosene Engine
Water Pump with Diesel Engine
Hand Tools
Secateurs
Folding Saw
Garden Rake
Garden Shovel
Hedge Shear
Lopper
Telescopic Hedge Shear
Telescopic Lopping Shear
Tree Pruner
Telescopic Steel Pipe & Fruit Picker Bag
Sheep Shear
Garden Tools
Electric Pressure Washer
Hedge Trimmer
Lawn Mower (Electric, Petrol & Manual)
LeafBlower
Cultivators and Accessories
Petrol and Diesel
Sprayers and Accessories
BatterySprayer
Portable Power Sprayer
Trolley Sprayer
Manual Knapsack Sprayer
Manual Pressure Sprayer
Rose Cans
Hose Crimping Machine
HTP Sprayer
HTP Delivery Hose
HTP Hose Reel
HTP Stand
HTP Gun / Lance(Brass Rod
Knapsack Power Sprayer
Mister / Duster / GranuelSpreader
HTP Sprayer Set with Diesel Engine
HTP Sprayer Set with Kerosene Engine
Fogging Machine
Milking Machine
Wood Shredder
Fodder Ensiling Chaff Cutter
Fodder Grinder Chaff Cutter
Fodder Mini Chaff Cutter
Harvester
Maize Sheller
Maize Sheller + Dehusker
Maize Combine Harvester
Onion Digger Carlotti Italy
Tea Leaf Harvester
Sugarcane Combine Harvester
Sugarcane Leaf Stripper
Transplanter and Post Hole Digger
Paddy Transplanter (2 & 8 Rows)
Transplanter-Vegetable & Tobacco
Post Hole Digger(4” to 14”Augers)

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Part No
Part Name
Part No
Part Name
E2-33
Spark Plug
E2-72
Fuel Pipe Long
708
E2-34
Gasket-Insulator
E2-72
Fuel Pipe Long
768
E2-35
Insulator
E2-73
Fuel Pipe Short
708
E2-36
Screw M5x20-Star
E2-73
Fuel Pipe Short
768
E2-37
Gasket -Carburetor
E2-74
N/A
E2-38
Carburetor
E2-75
Petrol Filter
E2-39
Air Cleaner Inside
Cover
E2-76
Screw M5x16-Star
E2-40
N/A
E2-77
Starter Assy
E2-41
Screw M5x50-Allen
E2-78
E- Ring
KisanKraft®
Warranty Certificate
(CUSTOMER COPY)
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 5 of 48
Product
Agricultural Knapsack Sprayer
(Power) / Agricultural Portable
Sprayer (Power)
(2-Stroke)
KisanKraft
Invoice Date
Brand
KisanKraft
KisanKraft
Invoice No.
Model
KK-708, KK-708(AL-1), KK-708X KK-707,
KK-P767, KK-P-768, KK-PPS-P769, KK-P780
KK-KPS-802, KK-KPS-162, KK-TPS-60T
WARRANTY
PERIOD
6-MONTHS
FOR THE SPECIFIED PERIOD FROM THE DATE OF
SALE OR DELIVERY WHICHEVER IS EARLIER.
Dealer’s
Invoice Date
Dealer’s Invoice No.
Buyer’s Info (Name, Address, Phone, etc.):
Dealer’s Stamp (Address, Phone, TIN, etc.):
Buyer’s Sign
Dealer’s Sign
Warranty Policy
What is covered: KisanKraft Limited and its manufacturers warrant this product to be free from defects in
material or workmanship. All parts defective in material and workmanship are covered.
This warranty will only cover defects arising under normal usage.
This warranty is limited to repair or replacement by KisanKraft Limited or its manufacturers of such parts as appear
to KisanKraft or its manufacturers, upon inspection, to be defective in material and/or workmanship. KisanKraft
or its manufacturers make no warranty with respect to items not manufactured or sold by them. No onsite
warranty is provided by KisanKraft Limited or its manufacturers. Defective items must be brought/sent to our
Authorized Dealer or KisanKraft Limited’s office for service.
What is not covered: The warranty shall become null and void and neither KisanKraft Limited nor any of its
manufacturers, nor its authorized dealers assumes any responsibility, if the failure was caused by the following:
(1) Operation of product with incorrect fuel or lubricants, (2) Incorrect usage of machine or misuse, (3) Lack of
maintenance, (4) Negligence, (5) Accident or physical damage, (6) Repairs made by unauthorized parties and/or
with unauthorized parts, (7) Improper set up, adjustments, tampering or altered products (8) Any modification to
the product what-so-ever.
Important: (1) Normal maintenance and adjustments to the product is the responsibility of the customer. (2)
Normal wear and tear are not covered under warranty. (3) Rubber/plastic parts and consumables such as blades,
clutch and clutch-bell, sparkplugs, nylon line, air-filters, fuel-filters, oil seals and gaskets etc. are not covered under
the warranty. (4) Electrical Motor, Electrical Parts, Battery Etc. are not covered under the warranty.
Incidental / Consequential Loss: KisanKraft Limited or its manufacturers will not be liable for general
damages, including bodily injuries, or for incidental or consequential damages including, but not limited to, loss
of use, loss of profits, loss of production, expense of substitute equipment or other commercial loss or damage.

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with KisanKraft by sending
the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Limitation of Liability: This limited warranty is in lieu of all other express warranties, obligations, or
liabilities. Any implied warranties, obligations or liabilities, including, but not limited to, any implied warranty of
merchantability shall be limited in duration to the applicable warranty period. Any action for breach of any
warranties hereunder, including, but not limited to, any implied warranty of merchantability must be brought
within the applicable warranty period.
Modifications of Warranty: No agent, representative, dealer, or employee of KisanKraft Limited or any of
its manufacturers has the authority to increase or alter the obligations of this warranty.
Assignment / Transfer of warranty: The warranty cannot be assigned and shall not transfer if the
product is resold by the first buyer. The above warranties are extended to the first end user (original purchaser),
and no warranty is made, nor authorized to be made assignable on resale by the first end user.
What you must do to obtain limited warranty service: To obtain performance of any obligation
under this warranty for failure during the applicable warranty period, you must deliver the defective product, to
the nearest Authorized Dealer, along with proof-of-purchase (invoice/receipt). KisanKraft Limited, its
manufacturers and its dealers reserve the right to inspect the claimed defective part(s) to determine if the
malfunction is the result of a defect covered by this warranty. Please note that the decision of KisanKraft Limited
with respect to any warranty claim is final.
After-sales Service (Including Warranty): KisanKraft Limited does not sell directly to consumers. All
sales or supplies are made through Authorized Dealers. It is the responsibility of the Authorized Dealer to provide
all after-sales service to consumers. Any warranty claim should be raised by dealer to KisanKraft Limited as per
warranty policy.
Jurisdiction: All disputes are subject to Bangalore court’s jurisdiction.
Notes:
➢This purchase is not contingent upon a product demonstration. The purchaser shall satisfy himself with the
product, including any product demonstration or verification of any function, before buying. KisanKraft
Limited or its authorized dealers, including online sellers, shall not be liable to give any on-site demonstration
after purchase of any of the product.
➢Any product once used will not be taken back by KisanKraft Limited.
➢Warranty and After Sale Services (including but not limited to installation, Demonstration, Repair, Routine
Maintenance etc.), should be done through the Authorized Dealer selling this product.
➢Dealers should have their own technician to provide After Sales Services to their Customers. KisanKraft
Limited provides free training to Authorized Dealer’s technicians at KisanKraft Limited’s head office, on
request from Authorized Dealer.
KisanKraft®
2 - STROKE PETROL ENGINE
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 43 of 48
Part No
Part Name
Part No
Part Name
E2-15
Screw M5x45-Allen
E2-58
Rope Reel
E2-16
Guide Cover Assy
E2-58/1
Ratchet Spring
E2-17
Screw M5x16-Star
E2-58/2
Ratchet Starter
E2-18
N/A
E2-59
Recoil Spring
E2-19
Crank Shaft Assy
E2-60
Screw -Ratchet
E2-20
Piston
E2-61
N/A
E2-21
Piston Pin
E2-62
Starter Rope
E2-22
Piston Rings
E2-63
Starter Handle
E2-23
Circlip-Piston Pin
E2-64
Start Reel
E2-24
Needle Bearing-
Piston Pin
E2-65
Start Claw
E2-25
Key-Crank Shaft
E2-66
Claw Spring
E2-26
Nut M8-Flanged
Hex
E2-67
N/A
E2-27
Fly Wheel
E2-68
Fuel Tank 708
E2-28
Ignition Coil
E2-68
Fuel Tank 768/800
E2-29
Cap-Spark Plug
E2-69
Fuel Tank Lid 708
E2-30
Grommet -Cord
Comp
E2-69
Fuel Tank Lid
768/800
E2-31
Cord Comp-Coil
E2-70
Gasket-Fuel Tank
Lid
E2-32
Screw M5x20-Star
E2-71
Fuel Pipe
Grommet

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
PETROL ENGINE (2-STROKE)-PARTS LIST
Part No
Part Name
Part No
Part Name
E2-1
Crankcase Big
E2-42
Air Filter Sponge
E2-1A
Crank Case Small
E2-43
Air Cleaner
Outside Cover
E2-1B
Fan Cover
E2-44
Screw -Air Filter
E2-2
Screw M5X25-
Allen
E2-45
N/A
E2-3
Screw M5X20-Star
E2-46
N/A
E2-4
Stop Ring 28-Inner
E2-47
Gasket-Muffler
E2-5
Gasket-Crankcase
E2-48
Muffler
E2-6
Bearing-6001
E2-49
N/A
E2-7
Oil Seal-Big
12x30x7
E2-50
N/A
E2-8
Oil Seal-Small
12x22x7
E2-51
Clutch Shoe Assy
E2-9
N/A
E2-52
N/A
E2-10
N/A
E2-53
Spring-Clutch
E2-11
N/A
E2-54
Clutch Bolt
E2-12
Cylinder
E2-55
Washer B-Clutch
E2-13
Gasket -Cylinder
E2-56
Washer A-Clutch
E2-14
Screw M5x16-Allen
E2-57
Starter Cover
KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 7 of 48
BEFORE GETTING STARTED
Please read and follow the instructions in this manual before using the machine. The user should be familiar
with the safety notices, machine performance, and maintenance, etc. The operation manual will be used later
in case of any repair, accessories replacement, and accessories procurement, so preserve it carefully.
SAFETY INSTRUCTIONS
1. Using this machine with extra high pressure is prohibited (≤35kgf/cm2) ；
2. The rotating parts should have a safety protective device;
3. Protective Clothing:
•Wear flange cap.
•Wear dirt/fog-proof glasses.
•Wear gauze mask.
•Wear long gloves.
•Wear coat guarding against poisons.
•Wear boots.
4. Spraying towards personnel and working at the downwind position are prohibited;
5. Running the machine without water or lubricating oil is prohibited;
6. Using special working solutions as strong acid, strong alkali, etc. is prohibited
7. Following personnel should not use the machine:
•Mentally challenged.
•Drunk.
•Under the age of 18 or older people.
•Person with no knowledge of the machine.
•Tired person or patient and others who cannot operate the machine normally.
•A person who has just exercised strenuously or has not slept enough. Women feeding
breast milk to the baby or is pregnant.
8. Spraying
•It is fine to carry out an operation during cool weather with little wind. For example, early
in the mornings or in the late afternoons as this can reduce the evaporation and drift of
chemicals and improve the protective effect.
•The operator should move windward.
•If your mouth or eyes are spattered with chemicals, wash them with clean water and then
visit a doctor.
•If the operator has a headache or dizziness, should stop working at once and consult a
doctor immediately.
•For the operator’s safety, misting/dusting must be carried out strictly according to the
instruction of the chemicals and agricultural requirements.

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with KisanKraft by sending
the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
•Spray over, according to pesticide manual to clean out any residual spray mixture in
chemical tank.
•After spraying always wash your hands and face thoroughly
OVERVIEW OF COMPONENTS
KK-707/708 / KK-708-(AL1) /KK-KPS-802/162:
KisanKraft®
2 - STROKE PETROL ENGINE
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 41 of 48
PETROL ENGINE (2-STROKE)-PARTS DIAGRAM

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
STORAGE
When releasing the engine from operation for more than 30 days, it must be serviced and
stored as follows with care to prevent the starting trouble or malfunction due to degeneration
of fuel.
1. Drain the fuel from the fuel tank and start to run the engine till it is stopped due to
use-up of fuel.
2. Wash the inside of fuel tank and fuel filter with white kerosene.
Use of fire is strictly prohibited
3. Removing the ignition plug, inject a small quantity of new engine oil through the
plughole. After idling slowly for few revolutions operating the recoil starter, install
the ignition plug. Pull the recoil starter again and stop it at the position where it is
felt heavy.
4. Clean the external surfaces with soft cloth and store it at a dry place free from
fires.
NOTE: If the unit is left over without draining fuel, impurities in the fuel could clog the fuel
passages such as the carburetor, fuel filter, or others, and cause engine troubles.
Make sure to drain the fuel when storing the unit for a long period of time.
Sufficient care must be taken not to use fires at the vicinity when handling the fuel.
KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 9 of 48
KK-P767/ P-768 / P769 / P780 & KK-TPS- 60T:
ASSEMBLY
KK-707/ 708 / KK-708-(AL1) /KK-KPS-802/162:
Attach the wide nozzle, the nozzle pipe, the ball
cock in an order to the spray hose, and connect the
other end of the hose to the spray outlet.

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with KisanKraft
by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
OPERATING INSTRUCTIONS
Pre-Operation Preparation:
Oiling
1. Make sure to use 2T exclusive oil.
2. Make sure that the engine is
stopped and cooled.
3. Neither overfill nor spill the fuel on
the engine
Dilution of chemicals/Charging the chemical tank
(Applicable for KK-707/ 708 / KK-708-(AL1) /KK-KPS-802/162)
Caution: Agricultural chemicals are extremely dangerous, and must be handled with utmost care.
Read the manual for the specific chemical carefully before use.
Dissolve water dispersible powder in a separate container before filling, be sure not to get foreign
material into chemicals.
Always fill the chemical tank through the strainer so that contaminants are not mixed into the
chemicals.
Open the air bleed nozzle, and bleed until the chemical is draining out, and then close the nozzle
securely .Before spraying the agrochemical, be sure to put on suitable protective clothing to
protect yourself against contact with and breathing it. Observe the following cautions for safe
operation:
a) Be sure to close the chemical tank cover securely.
KisanKraft®
2 - STROKE PETROL ENGINE
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 39 of 48
INSPECTION AND SERVICE BEFORE EACH OPERATION
Cleaning of air cleaner
Wash the element with white kerosene and
then immerse it in engine oil.
Squeeze it tightly with single hand.
Use of fire is strictly prohibited
Cleaning and service at respective sections
•Clean thoroughly around the muffler.
•Clean the cooling fins and the cooling air inlet.
•Inspect and retighten bolts and nuts.
•Inspect the fuel leakage.
INSPECTION AND SERVICE AT EVERY 50-HOUR
Cleaning and adjustment of ignition plug
After removing carbon accumulated on the
electrodes and the insulator, adjust the clearance
between the electrodes at 0.6 ~ 0.7 mm
When mounting the plug cap, push it in securely
Cleaning of fuel filter
Using a piece of wire, or the likes, pull out the fuel filter and wash with clean white
kerosene. When it is fouled heavily, replace the filter and also wash the tank inside.
Use of fire is strictly prohibited
Carbon removal
Remove carbon from the muffler in-/outlet, cylinder and piston.
This work requires engine servicing skill and some tools. Consult the dealer or nearest
service center.
CAUTIONS DURING INSPECTION
•Disconnect the ignition plug wires before inspection or adjustment to prevent
unexpected start of engine.
•Do not touch the engine immediately after operation to prevent burn.
•Use of fire is strictly prohibited when handling the fuel (gasoline).
•Make sure to clean spilled fuel sufficiently before using the engine.
•Do not wash the engine with water.
•Do not change thesetting revolution speed carelessly. (Consult your dealer when
changing the revolution speed.)

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
INSPECTION AND SERVICE
Table of regular inspections
Time
Item
Before
Each
Operation
At
Every
50-
hours
At Every
100-
hours
2
Years
Inspection and retightening of
bolts, nuts
✓
Inspection of fuel leakage
✓
Inspection, cleaning of air cleaner
✓
Cleaning at cooling air inlet, cooling
fin and around muffler
✓
Inspection, cleaning of ignition plug
✓
Inspection, cleaning of fuel filter
✓
Removal of carbon from muffler,
cylinder
✓
Cleaning of spark arrestor
✓
Replacement of ignition plug
✓
Replacement of fuel piping (fuel
pipe and grommet)
✓
KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 11 of 48
b) Check the spray hose and nozzle connections to make sure there are no leakage.
c) Always stop the engine before refilling the fuel tank or changing the nozzle.
d) When carrying a full chemical tank, be careful not to lose your balance.
Starting the Engine (Applicable for all the models):
Important: When starting the engine, be sure to fill the chemical tank with pure water or chemical
liquid. Never run the engine when the chemical tank is empty.
1. Pump the primer bulb until fuel canbe seen flowing through the fuel return line, and pull
the choke leverto full close.(During hot weather and when the engineis already warmed
up, the choke lever may be set to either half open or full open ).
2. Set the throttle lever to the middle speed position (not necessarily to maximum).
KK-707/ 708 / KK-708-(AL1) /KK-KPS-802/162:
Matching mark at
Starting

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with KisanKraft
by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
KK-P767/ P-768 / P769 / P780 & KK-TPS- 60T:
3. Pull the recoil starter lightly 2-3 times.
4. Pull the recoil starter strongly to start the engine.
5. If the engine stops after a few revolutions, set the choke to half open, and pull the recoil
starter rope strongly again to restart it.
Note: If the engine does not catch even after the starter is pulled several times, set the
choke lever to full open and pull the starter rope. Be sure not to pull the starter lever
completely out. After the engine starts, open the choke lever slowly, move the throttle
lever to the low –speed side, and let the sprayer warm up for 2-3 minutes.
Pull briskly:
KisanKraft®
2 - STROKE PETROL ENGINE
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 37 of 48
ADJUSTING THE CARBURETOR
Engine revolution speed is adjusted at the optimum condition before shipping
from the factory. It should be adjusted only when it fails to operate properly. (Consult
your dealer when adjustment is necessary.)
1. Use the slow speed adjusting
screw to adjust the slow speed
revolutions.
•Right turns: Increase the
revolution speed.
•Left turns: Slow down the
revolution speed.
Increasing the slow revolution
excessively causes the driven
equipment unable to stop
even if the throttle lever is
returned. The revolution
speed should not be increased
excessively.
2. In case with the slow speed
fuel adjusting screw Normal
position is where it is returned
by one turn from the fully
closed position (right turn).
•Right turns: Increase the
thickness of fuel.
•Left turns: Decrease the
thickness of fuel.
3. In case with the high speed fuel
adjustment screw
•Right turns: Decrease the
thickness of fuel.
•Left turns: Increase the
thickness of fuel.
Fuel adjustment for the
carburetor is completed at the
optimum condition before
shipping from the factory.
When it is necessary to adjust,
consult your dealer.
Do not decrease the thickness
of fuel too much.
(It could result in the seizure
trouble of engine.)
Slow Speed Adjusting Screw
Slow speed fuel
Adjusting screw
High speed fuel
adjusting screw

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
PRECAUTIONS DURING OPERATION
•After starting the engine, set
the throttle lever at the slow
speed position and warm up
the engine for approx. 2~3
minute. As the engine worms
up, the engine will be
accelerated smoothly.
•Do not attempt to raise the engine speed abruptly immediately after the start
because the lubrication oil may not be distributed at all over the engine.
•If the throttle lever is turned to the fully opened position, the revolution speed
picks up to a considerably higher level, which could not only shorten the life of
engine but also cause trouble. It should be avoided to race the engine at high
speed under no load condition or raise the speed unnecessarily.
•Before starting operation, make sure to inspect the engine in accordance with the
“Inspection before starting the engine”.
•Do not operate the engine at the indoor or a place with poor ventilation. (Exhaust
gas contains odorless and harmful carbon monoxide.)
•Do not insert in or approach hands or foot at the moving or rotating sections.
•Stop the engine immediately if it has been discovered any leakage of fuel or gas
from the carburetor, muffler, fuel tank, crankcase, cylinder or mating face at
respective sections. (Contact a dealer or service center for repair.)
•Do not change the setting revolution speed of engine unnecessarily.
•Be careful not to touch highly heated muffler or sections on the engine to avoid
possible risk of burn.
•Do not operate the engine while withered grasses, leaves or other inflammable
substances are sticking in or around the muffler cover.
•Do not touch the ignition plug cap or high-voltage cord during operation. (There
is risk of electric shock or physical injury.)
•Do not operate the engine with the muffler or air cleaner cover removed
KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 13 of 48
Operation (KK-707/ 708 / KK-708-(AL1) /KK-KPS-802/162)
1. Turn the handle of the control
valve, and set it to the position
for HERBICIDE,
INSECTICIDE or HIGH
PRESSURE to match the
pressure of the operating
conditions.
2. Check the spraying conditions
and the status of the
equipment, then shoulder the
equipment and set the throttle
lever to the high speed
position.
3. When the nozzle cock is opened, chemicals will be atomized as they come out of the
nozzle.
IMPORTANT
1. When the pressure control valve is changed to INSECTICIDE or HERBICIDE, with the
throttle being fully open at HIGH PRESSURE positon of pressure control valve handle,
the engine speed will become too high, corresponding to the extent of lowered pressure.
Therefore, use the equipment withthe throttle lever somewhat turned back fromthe fully
opened condition, when the equipment is used at the position for INSECTICIDE or
HERBICIDE.
2. Be careful of the amount of fuel in the tank, and refill it when it becomes low.

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with KisanKraft
by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
To Stop:
Temporary halt during operation:
1. Close the spray gun, and return the throttle lever to low speed.
2. Press the engine stop button.
3. After the engine stops, set the sprayer down and close the fuel cock.
Stopping the sprayer after completing spraying:
1. Remove the chemical tank drain cap, drain off all of the chemical
2. Fill the chemical tank with clean water, operate the engine, and clean the pump and
hose interior by spraying the clean water. Drain off the remaining water through the
drain.
Start the engine at just less than high speed for 15-20 seconds to spray out the water in the spray
hose and nozzle. When water stops coming from the nozzle, turn off the engine at once.
KisanKraft®
2 - STROKE PETROL ENGINE
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 35 of 48
1. Set the throttle lever at the slow speed
position.
2. Turn the engine switch to the “OFF” position.
(Switch position may vary depending on the
specifications. Refer to the instruction
manual of driven equipment.)
In chase of a push button type switch, keep
pressing the push button till the engine stops
completely.
•Replenish the fuel before using up
completely. It will make easier at the
next starting.
•When there is no subsequent work,
drain the fuel from the fuel tank and
restart the engine to use up the fuel
remaining in the carburetor.
CAUTION
•Place the engine at a horizontal position
when the driven equipment is not used at
the rest time, or others, in summer season.
(If the tank is tilted as much as the inside
of fuel cap is submerged in the fuel, the
fuel may leak.)
•Do not touch the engine body, especially
the muffler, during or immediately after
stopping the operation.
(There is risk of burn.)

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
5. While holding down the engine firmly,
grasp the recoil starter grip and pull
vigorously
CAUTION: a) When the engine stops on
the way after starting, or
b) When the engine fails to start
after trying the recoil
operation for 7 to 8 times.
Return the starter lever to the operating
position and try the recoil operation.
6. If you move the throttle lever to thehigh-speed side alittle after the engine has
started, the starter lever returns to the operating position. Continue the warm-
up operation for 2 to 3 minutes in this condition. Observing the condition of the
engine, move the throttle lever to a desired engine speed.
START
CAUTION
•Before starting the engine, confirm that the area of radius 15 m around the engine
is completely evacuated.
•Do not operate the engine when any flammable material (gasoline, volatile
chemicals, or others) is present around it.
•Driven equipment may start simultaneously with the start of engine. Carefully
read the instruction manual of the equipment and start the engine carefully.
•When a class FC oil is used, a larger resistance may be felt when pulling the
recoil starter grip under low temperature condition or at the initial operation at the
next season. This is related to the characteristic of the oil and there is no problem
on the engine. Once started, it will return to the normal condition
Concerning New Start System
It can start even if it is pulled slower than normal.
•If the rope is pulled (vigorously) till it will not come out any more, it could damage
the recoil mechanism.
•Do not disassemble the recoil.
It is dangerous to disassemble the inside of recoil. (Consult your dealer when it
is necessary to replace related parts.)
•If the decompression slot of cylinder is clogged, the engine may start slower than
normal. Clean the slot to restore the normal condition.
STOP
KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 15 of 48
Operation (KK-P767/ P-768 / P769 / P780 & KK-TPS- 60T):
1. Turn the handle of the control valve to
match the pressure of operating
conditions.
2. Check spraying conditions and the
status of the equipment, and set the
throttle lever to the high speed
position.
3. When the nozzle cock is opened, chemicals will be atomized as they come out of the
nozzle.
IMPORTANT
1. After each 4 continuous working hours, please turn the cap of grease cup for 1 or 2
rounds. This will lubricate the piston and prolong its life.
2. After every 100 working hours, please inspect the engine oil level in the pressure
pump(you can see it from the oil window of the pump).In case, the oil level is lower
than1/3 position, please remove the oil inlet bolt and add engine oil up to 2/3 position
3. Be careful of the amount of fuel in the tank, and refill it when it becomes low.
To Stop:
Temporary halt during operation:
1. Close the spray gun, and return the throttle lever to low speed.
2. Press the engine stop button.
3. After the engine stops, close the fuel cock.
Stopping the sprayer after completing spraying:
1. Drain off all of the chemical from the chemical tank.
2. Fill the chemical tank with clean water, operate the engine, and clean the pump and
hose interior by spraying the clean water.

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with KisanKraft
by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Start the engine at just less than high speed for 15-20 seconds to spray out the water
in the spray hose and nozzle. When water stops coming from the nozzle, turn off the
engine at once.
MAINTENANCE AND STORAGE
Cleaning the air cleaner:
Plug:
KisanKraft®
2 - STROKE PETROL ENGINE
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 33 of 48
6. When the engine has started, return the choke lever gradually to the fully
opened
position
(at the
Mark).
If only exploding sounds are heard, but it does not start, return the choke
lever to the fully closed position and pull the starter grip vigorously once
again.
START (STARTER LEVER TYPE UNIT)
1. Turn the engine switch to the “ON” side.
2. Set the throttle lever at the slowest
speed position.
3. Push the priming button repeatedly with
finger till it hits the top. (More than 10
times)
Pressing the priming button is necessary
to prime the fuel to facilitate the start-up.
Since any excess amount of primed fuel
returns to the tank, there is no problem
of over-priming. Prime the fuel rather
more than sufficiently to avoid starting
trouble.
4. Turn down the starter lever of carburetor
to set it at the start position.
It is not necessary to operate the starter
lever when the engine is warmed up (For
about 15 minutes after stopping the
engine.)
(To be left in the operating position)
Depending on specifications, the starter
lever may be provided at the throttle wire
side.
Engine switch
Slow speed

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
OPERATION INSTRUCTIONS
Methods of starting & stopping the engine
START (CHOKE TYPE UNIT):
1. Turn the engine switch to the “ON” side.
2. Set the throttle lever at the slow speed
position.
3. Push the priming button repeatedly with
finger till it hits the top. (More than 10 times)
Pressing the priming button is necessary to
prime the fuel to facilitate the start-up. Since
any excess amount of primed fuel returns to
the tank, there is no problem of over-priming.
Prime the fuel rather more than sufficiently to
avoid starting trouble.
4. Turn the choke lever to the fully closed
position
(at
the
Mark).
When sufficient fuel is retained and the
engine is warm, set the choke lever at the
fully opened
position
(at the
mark)
5. While holding down the engine firmly, grasp
the recoil starter grip and pull vigorously
Engine
switch
Slow
speed
Priming
button
Choke lever
Recoil starter grip
Main
unit
KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 17 of 48
Storage:
After using the sprayer for the season, store it until the next season of use as follows:
1. Drain off all fuel from the fuel tank and the carburetor.
2. Remove the spark plug and coat the cylinder with a small amount of oil. Pull
the recoil starter lightly 2-3 times to spread the oil over the cylinder completely
as shown in the figure below.
3. Pull the recoil starter out slightly and stop it in place where you feel the pull
start (compression starts).
4. Clean the entire sprayer completely, cover it so it does not accumulate dirt
and dust, and store it in a dry, cool location.

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with KisanKraft
by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
TECHNICAL SPECIFICATIONS
Model
KK-
708-
AL1
KK-
708X
KK-
707/708
KK-
KPS-
162
KK-
KPS-
802
KK-
TPS-
60T
KK-
P767/P-
768
KK-
PPS-
P769
KK-
P780
Rated Power
0.7kW
(1hp)
0.75 kW
(1 hp)
0.7 kW
(0.94
hp)
0.7kW (1hp)
Displacement
26 cc
34 cc
25.6 cc
26 CC
34 cc
43cc
Engine Type
2 - stroke
RPM
7500
6500
7500
7000
7500
Fuel Used
Petrol
Fuel Tank
Capacity
750 ml
600 ml
750 ml
600 ml
600 ml /
750 ml
600 ml
1 L
Chemical tank
capacity
20 L
25 L
60 L
N/A
Oil (Mixing)
40ml (2T) oil per 1 Liter of Petrol & 100 ml (20W 40 Grade) for Gear Box
Fuel
Consumption /
Out Put
Capacity
500-600 ml/hour (Engine) &
420 Liter/hour (Output)
7.49
L/min
500-600 ml/hour (Engine) & 420 Liter/hour
(Output)
Weight
11 kg
9 kg
8.75
kg
10 kg
(With
hose
) 70
kg
10.2 kg
10 kg
Feature
Knapsack
Trolley
Portable
Suction
Volume
7-8 L/min
7.49
L/mi
n
8 L/min
9 L/min
KisanKraft®
2 - STROKE PETROL ENGINE
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 31 of 48
INSPECTION OF RESPECTIVE SECTIONS:
Make sure to inspect these sections before operating the engine.
Inspection of fuel
•Is sufficient quantity of oil reserved?
•Is not the fuel degenerated?
•Use the proper fuel referring to the “Fuel” section.
CAUTION
•Sufficient care must be taken on the fire not only when replenishing but also
handling fuel. It could cause fire or explosion.
•Securely close the oil tank cap. Fuel may leak if the cap is tightened aslant. It
will never leak if the cap is tightened properly.
(Excluding: TL tank cap breather type)
Inspection of clogging
•Check the cooling fins, around the muffler and cooling air inlet for trash or
withered grasses trapped.
•Remove them if necessary
Inspection of air cleaner
•Is not fouled the air cleaner element?
•When the element is fouled or it is not impregnated with oil, inspect and service
it in accordance with “Inspection and servicing before each operation”
Inspection of screws and nuts
•Check respective sections for loose or missing screws or nuts.
•Service them if necessary.
Inspection of fuel pipes
•Check for cracks or fissures on the fuel pipe and grommet, disconnection or fuel
leakage from joints on the fuel tank and carburetor.
CAUTION
Cracks, fissures or disconnection from joints could cause fire or explosion by leaked fuel.
Service or replace damaged fuel pipe and grommet.

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with
KisanKraft by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
INSPECTION BEFORE OPERATING THE ENGINE
NOTE: In 2 Stroke engine the gasoline and engine oil are mixed and poured together.
FUEL: Use mixed oil of ordinary regular gasoline for vehicle and special 2-cycle engine oil
with the proportion as shown by the following table.
Mixing ratio (Volumetric ratio):
Petrol: 2-cycle engine oil
40: 1
•Do not use degenerated oil (with sour smell).
•(It could cause engine trouble such as the starting error, insufficient output, etc.)
•Make sure to clean spilled fuel. It could foul clothes or cause fire.
•Do not use 4-cycle engine oil. (It could cause fouled plug, bound piston ring,
clogged muffler, or other problem.)
•Take care while handling gasoline. (As there is a risk of explosion.)
ADJUSTMENT OF THROTTLE WIRE:
Adjust the play on the throttle wire to 0.5 ~ 1.0 mm.
LARGER PLAY
•It could cause the starting trouble.
•Revolution speed could rise unexpectedly when the external wire of throttle wire
comes off from the position.
NO PLAY
•Driven equipment may fail to stop even if the throttle lever is returned.
Throttle wire adjust screw
Lock nut
Play (As much as the external wire
can move lightly)
KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 19 of 48
TROUBLESHOOTING
Pump:
Trouble
Cause
Remedy
No Suction
Hose is Loose
Tighten the hose carefully
Suction hose is clogged with
chemicals.
Disassemble and clean the hose.
Worn piston packing.
Replace with a new piston
Foreign object in valve parts.
Disassemble and clean the valve.
Poor spray quality
Worn piston packing
Replace with a new piston
Flaw in cylinder inner surface
Replace with a new cylinder
Flaw in exhaust valve
Replace with a new valve
Worn pressure control valve
handle
Replace with a new handle
Foreign object in valve parts
Disassemble and clean the valve.
Worn nozzle hole.
Replace with a new nozzle.
Too many nozzle attached
Reduce number of nozzles or replace
with nozzle of smaller holes.
When engine fails to start:
Trouble
Cause
Remedy
There is fuel,
but spark
plugs fail to
ignite.
There is
power at the
terminal.
Drawing too much fuel
Tuning the carburetor
Faulty spark plug gap.
Adjust the spark plug gap
Faulty spark plug insulation.
Replace the spark plug
No power at
the terminal
Faulty TCI unit or broken wire
Replace the ignition coil.
A break or short in the ignition
coil.
There is fuel
and spark
plug ignites
Compression
is good
Bad Mixture
Adjust the carburetor
Compression
is bad
Faulty packing
Tighten the spark plug
Spark plugs not tightened
properly
Tighten the spark plug
Piston rings are sticking
Replace the piston ring
No fuel in the
carburetor
No fuel in the tank
Fill the tank with fuel
Fuel valve is faulty or fuel tank
air vent is clogged.
Clear air vent hole
Lines are bent
Replace lines

KisanKraft®
Agricultural Portable Sprayer (Power)
KK-P767/ P768/ P769/ P780, KK-TPS-60T
Agricultural Knapsack Sprayer (Power)
KK-707/ 708/X/AL, KK-KPS-162 / 802
This warranty is null & void, if you fail to register the warranty with KisanKraft
by sending the KisanKraft Copy with dealer’s stamp.
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Engine fails to run smooth:
Trouble
Cause
Remedy
No power
Compression is
good and there
is no misfire
Air cleaner element is
plugged up.
Clean or replace air cleaner if
necessary
Air has entered fuel line
joints.
Clear the fuel line
Faulty choke lever
Replace choke lever
Carbon build up on
cylinder muffler.
Clean the muffler
Compression is
bad
Burnt spark plugs
Replace the spark plug
Short in cable
Replace the cable
Bad mixture or piston ring
wear.
Replace the piston ring
Marks on cylinder. Cracks
in the piston head
Replace the piston
Engine overheated
Fuel is too low (mixture is
too thin).
Engine over oiling.
Faulty mixture, not enough
mixture.
Clear the lines
Carbon piled up,
overloaded operation.
Clean the carbon
Faulty spark plugs.
Replace the spark plugs
Plugged cylinder or
coolant lines
Clean the coolant lines
Inaccurate explosion
Carburetor not adjusted
properly.
Adjust the carburetor gap properly
Faulty spark plugs.
Replace the spark plug
Faulty magneto or internal
short
Replace he magnet
Engine doesn’t sound right
Overheated cylinders
Replace the cylinder
Overload operation
Right quantities of petrol and oil
should be mixed to enable proper
lubrication
Faulty mixture or incorrect
ratio
Internal engine damage
Replace the necessary
spares/contact service person
Slow acceleration
Carburetor not adjusted
properly or faulty
compression
Adjust the carburetor gap properly
Poor gasoline oil quality
Use good quality gasoline-oil
mixture.
Carbon pile up
Clean the carbon
KisanKraft®
2 - STROKE PETROL ENGINE
: www.kisankraft.com
: [e-mail]
: +91.80. 6835 7800
Page 29 of 48
COMPONENTS OVERVIEW
1. Recoil starter grip
2. Starter lever
3. Cooling air inlet
4. Fuel tank cap
5. Fuel tank
6. Muffler
7. Exhaust outlet
(Types vary depending on the
specifications.)
8. Engine switch
(Types vary depending on the
specifications.)
9. Clutch
10. Ignition plug cap
11. Air cleaner
12. Carburetor
13. Priming button