KitchenAid KHIS6503 User manual

Instructions for use

3
Installation diagrams 4
Important safety instructions 6
Safeguarding the environment 8
Declaration of conformity 8
Before use 8
Existing pots and pans 8
Recommended pot bottom widths 8
Installation 9
Electrical connection 9
Instructions for use 11
Cleaning 13
Troubleshooting guide 13
Noises made by the hob 13
After-Sales Service 14
Power level table 14

4
210 mm
145 mm
280 mm
Installation diagrams

5
Min. 10 cm
Min. 3 cm
Max. 6 cm
Min. 5 mm
Installation diagrams
3
21
X4
483 mm
553 mm
30 mm
+1
0
580
650
700 mm
510 mm
52 mm
R = Min. 6,5 mm
Max. 8 mm
490 mm
560 mm
0
+2
0
+2
Min. 50 mm

6
YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT
This manual and the appliance itself provide important safety messages,
to be read and always observed.
This is the danger symbol, regarding safety, warning of potential
risks to users and others.
All safety messages will be preceded by the danger symbol and
the following words:
Indicates a hazardous situation which, if
not avoided, will result in serious injury.
Indicates a hazardous situation which, if
not avoided, could cause serious injury.
All messages relevant to safety specify the potential risk to which they
refer and indicate how to reduce the risk of injury, damage and electric
shocks due to incorrect use of the appliance.
Make sure to comply with the following:
- Use protective gloves to perform all unpacking and installation
operations.
- The appliance must be disconnected from the power supply before
carrying out any installation operation.
- Installation and maintenance must be carried out by a specialised
technician, in compliance with the manufacturer’s instructions and the
local safety regulations in force. Do not repair or replace any part of
the appliance unless specifically stated in the user manual.
- The appliance must be earthed.
- The power cable must be long enough for connecting the appliance,
fitted in the cabinet, to the power supply.
- For installation to comply with the current safety regulations, an
omnipolar switch with minimum contact gap of 3mm is required.
- Do not use multi-sockets or extension cords.
- Do not pull the appliance’s power cable.
- The electrical parts must not be accessible to the user after installation.
- The appliance is designed solely for domestic use for cooking food.
No other use is permitted (e.g. heating rooms). The Manufacturer
declines any liability for inappropriate use or incorrect setting of the
controls.
WARNING
DANGER
IMPORTANT SAFETY INSTRUCTIONS

7
- The appliance and its accessible parts become hot during use. Care
should be taken to avoid touching heating elements. Very young (0-3
years) and young children (3-8 years) shall be kept away unless
continuously supervised.
- Children from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge
can use this appliance only if they are supervised or have been given
instructions on safe appliance use and if they understand the hazards
involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
- Do not touch the appliance heating elements during and after use. Do
not allow the appliance to come into contact with cloths or other
flammable materials until all the components have cooled down
completely.
- Do not place flammable materials on or near the appliance.
- Overheated oils and fats catch fire easily. Pay attention when cooking
food products rich in fat and oil.
- A separator panel (not supplied) must be installed in the compartment
under the appliance.
- If the surface is cracked, switch off the appliance to avoid the
possibility of electric shock. (only for appliances with glass surface).
- The appliance is not intended to be operated by means of an external
timer or separate remote control system.
- Unattended cooking on a hob with fat or oil can be dangerous and
may result in fire. NEVER try to extinguish a fire with water, but
switch off the appliance and then cover flame e.g. with a lid or a fire
blanket.
Danger of fire: do not store items on the cooking surfaces.
- Do not use steam cleaners.
- Metallic objects such as knives, forks, spoons and lids should not be
placed on the hob surface since they can get hot.
- After use, switch off the hob element by its control and do not rely on
the pan detector. (only for appliances with glass surface).

8
Disposal of packing
The packing material is 100% recyclable and
marked with the recycling symbol . The various
parts of the packing must not be dispersed in the
environment, but disposed of in compliance with
local regulations.
Disposal
This appliance is marked in conformity with
European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring that this appliance is correctly
disposed of, the user can help prevent potentially
negative consequences for the environment and the
health of people.
The symbol on the appliance or the
accompanying documentation indicates that this
product should not be treated as domestic waste but
must be taken to an appropriate collection point for
recycling WEEE.
Energy saving
For optimum results, it is advisable to:
• Use pots and pans with bottom width equal to
that of the cooking zone.
• Only use flat-bottomed pots and pans.
• When possible, keep pot lids on during cooking.
• Use a pressure cooker to to save even more
energy and time.
• Place the pot in the middle of the cooking zone
marked on the hob.
Safeguarding the environment
This appliance, has been designed, manufactured
and marketed in conformity with the safety
requirements of “Low Voltage” Directive
2006/95/EC (replacing 73/23/EEC as amended) and
protection requirements of “EMC” Directive
2004/108/EC.
Declaration of conformity n
IMPORTANT: The cooking zones will not switch on if pots are not the right size.
Only use pots bearing the symbol “INDUCTION SYSTEM” (Figure opposite).
Place the pot on the required cooking zone before switching the hob on.
Before use
Use a magnet to check if the pot is suitable for the induction hob: pots and pans are unsuitable if not
magnetically detectable.
- Make sure pots have a smooth bottom, otherwise they could scratch the hob. Check dishes.
- Never place hot pots or pans on the surface of the hob’s control panel. This could result in damage.
Existing pots and pans
OK NO
Recommended pot bottom widths
Ø 28 cm
XL
Ø 17 cm min

28 cm max Ø 21 cm
L
Ø 15 cm min

21 cm max
Ø 14,5 cm
S
Ø 10 cm min

14,5 cm max

9
After unpacking the product, check for any damage during transport.
In case of problems, contact the dealer or the After-Sales Service.
For built-in dimensions and installation instruction, see the pictures in page 5.
PREPARING THE CABINET FOR FITTING
- Install a separator panel under the hob.
- The lower part of the product must not be accessible after installation.
- Do not fit the separator panel if an undertop oven is installed.
• The distance between the underside of the appliance and the separator
panel must respect the dimensions given in the figure.
• In order to ensure the correct operation of the product, do not obstruct
the minimum required clearance between the hob and the top of the unit
(min. 5 mm).
• If an undertop oven is installed, make sure the oven is equipped with a
cooling system.
• Do not install the hob above a dishwasher or washing-machine, so that
the electronic circuits do not come into contact with steam or moisture
which could damage them.
• In the case of flush-mounted installation, call the After-Sales Service to request assembly of screws kit
4801 211 00112.
• To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of
the appliance.
WARNING
min 5 mm
min 5 mm
min 20 mm
min 5 mm
Installation
- Disconnect the appliance from the power supply.
- Installation must be carried out by qualified personnel who know the current safety and
installation regulations.
- The manufacturer declines all liability for injury to persons or animals and for damage to
property resulting from failure to observe the regulations provided in this chapter.
- The power cable must be long enough to allow the hob to be removed from the worktop.
- Make sure the voltage specified on the dataplate located on the bottom of the appliance is the
same as that of the home.
WARNING
Electrical connection

10
CBA
Wires Number x size
220-240 V ~ +
3 x 4 mm2
230-240 V ~ +
3 x 4 mm2(Australia only)
220-240 V 3 ~ +
4 x 1,5 mm2
380-415 V 3N ~ +
5 x 1,5 mm2
380-415 V 2N ~ +
4 x 1,5 mm2
380-415 V 3N ~ 220-240 V ~ 230-240 V ~ (Australia only)
220-240 V ~ (UK only)
380-415 V 2N ~ 220-240 V 3 ~
(Belgium only)
380-415 V 2N ~
(NL only)
Connection to the terminal block
For the electrical connection, use an H05RR-F or H05V2V2-F cable as specified in the table below.
Electrical connection
Important:
- Based on the wiring diagram (see figure) either keep or remove the metal jumpers between the screws
on the terminal block L1-L2 and N1-N2.
- If the cable is provided, see the connection instructions attached to the cable.
- Make sure all six screws on the terminal block are tightened after connecting the cables.
Example of jumper present (left) or removed (right). See the wiring diagram for details (the jumpers can be
between L1-L2 and between N1-N2).
Connect the yellow/green earth wire to the terminal with the symbol .
This wire must be longer than the other wires.
1. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block
hinge (B).
2. Insert the power cable in the cable clamp and connect the wires to the terminal block as indicated in the
connection diagram located near it.
3. Secure the power cable with the cable clamp.
4. Close the cover (C) and screw it on the terminal block with the previously removed screw.
Each time the power is connected, the hob performs an automatic check for a few seconds.
If the hob already has a power cable, follow the instructions attached to the cable. Connect the appliance to
the power supply by means of a multipole switch with minimum contact gap of 3mm.