KitchenAid 5KSMSFTAA User manual

5KSMSFTAA
W11221354A.indd 1 6/11/2018 12:12:26 PM

PARTS AND FEATURES
PARTS AND ACCESSORIES
Ingredient hopper
Swivel chute
On/off
button
Weight unit
toggle
Tare button
Sifter
Screen
Collar
Sifter assembly
(see detail below)
Sifter housing
Lid/scale plate
Digital scale
Digital scale display and control panel Sifter assembly detail
Ingredient valve
lb/oz/g
gozlb
W11221354A.indd 2 6/11/2018 12:12:26 PM

ENGLISH
SIFTER+SCALE ATTACHMENT SAFETY | 3
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety
precautions should always be followed, including
the following:
1. Read all instructions. Misuse of appliance may result in
personal injury.
2. This appliance is not intended for use by persons
(including children) with reduced physical, sensory,
or mental capabilities, or lack of experience or
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
3. Children should be supervised to ensure that they do
not play with the appliance.
4. To protect against risk of electrical shock, do not put
appliance in water or other liquid.
5. Never leave the appliance unattended while it is in
operation.
6. Turn the appliance off, unplug from outlet and detach
the Sifter+Scale attachment from appliance before
cleaning and when not in use. Turn the appliance off
and make sure the motor stops completely before
putting on or taking off parts.
SIFTER+SCALE ATTACHMENT SAFETY
W11221354A.indd 3 6/11/2018 12:12:27 PM

4| SIFTER+SCALE ATTACHMENT SAFETY
SIFTER+SCALE ATTACHMENT SAFETY
7. Avoid contacting moving parts. Keep hands, hair, and
clothing, as well as spatulas and other utensils away
from accessories during operation to reduce the risk of
injury to persons and/or damage to the appliance.
8. The use of attachments not recommended or sold by
KitchenAid may cause re, electric shock, or injury.
9. Refer to the “Care and Cleaning” section for
instructions on cleaning the surfaces in contact with
food.
10. Also see the Important Safeguards section included in
the Stand Mixer Use and Care Guide.
11. This appliance is intended to be used in household
and similar applications such as:
- staff kitchen areas in shops, ofces or other working
environments;
- farmhouses;
- by clients in hotels, motels and other residential
type environments;
- bed and breakfast type environments.
SAVE THESE INSTRUCTIONS
W11221354A.indd 4 6/11/2018 12:12:27 PM

ENGLISH
USING THE SIFTER+SCALE ATTACHMENT | 5
USING THE SIFTER+SCALE ATTACHMENT
SIFTER+SCALE CONFIGURATIONS
The Sifter+Scale attachment is compatible with all household KitchenAid Stand Mixers,
including all accessory stainless steel, glass, and ceramic bowls. It is not compatible with the
Precise Heat Mixing Bowl, Ice Cream Maker, or the Pouring Shield.
The Sifter+Scale attachment can be used in multiple ways: to weigh and sift ingredients while
slowly feeding them into the mixer bowl or into a separate container, to weigh and feed
ingredients without sifting, and to weigh ingredients on your countertop.
To weigh, sift, and slowly feed ingredients into
mixer bowl or separate container: Use the complete
attachment for recipes calling for ingredients to be
sifted and fed slowly into the mixer bowl or a separate
container.
To weigh and feed ingredients into bowl without
sifting: Use the attachment without the sifter when
weighing and feeding larger ingredients, such as whole
oats, that do not need to be sifted. To add those
ingredients slowly, you can limit the flow by using the
ingredient valve.
To use as a countertop scale: Set the scale on your
countertop or table and place the lid/scale plate on
top.
W11221354A.indd 5 6/11/2018 12:12:27 PM

6| USING THE SIFTER+SCALE ATTACHMENT
ATTACHING THE SIFTER HOUSING TO THE STAND MIXER
Before using your Sifter+Scale for the first time, wipe the ingredient hopper, sifter assembly,
and swivel chute with a warm damp cloth, then wipe clean with a damp cloth. Do not wash the
sifter housing or digital scale. Dry with a soft cloth. See the “Care and cleaning” section for
complete instructions.
1 Turn the Stand Mixer off and unplug.
2
For Stand Mixers with a hinged attachment hub
cover: Flip up to open.
For Stand Mixers with a removable attachment hub
cover: Turn the attachment knob counterclockwise to
remove attachment hub cover.
USING THE SIFTER+SCALE ATTACHMENT
3
Insert the attachment shaft housing into the
attachment hub, making certain the power shaft fits
into the square hub socket. If necessary, rotate the
attachment back and forth. The pin on the attachment
housing will fit into the notch of the hub rim when in
the proper position.
4 Tighten the Stand Mixer attachment hub knob
clockwise until the attachment is completely
secured to the Stand Mixer.
W11221354A.indd 6 6/11/2018 12:12:28 PM

ENGLISH
USING THE SIFTER+SCALE ATTACHMENT | 7
USING THE SIFTER+SCALE ATTACHMENT
ASSEMBLING THE SIFTER+SCALE ATTACHMENT
1
To install the swivel chute: Lower the swivel chute
into the sifter housing at an angle, aligning the marks
on the swivel chute with the marks above the notches
on the inside of the sifter housing. Properly installed,
swivel chute will be seated securely in the sifter
housing and will rotate easily.
TIP: Aligning the handle tab on the chute with one of the notches as you lower the swivel
chute into the sifter housing will help you to line up the marks.
2
To install the sifter assembly: Lower the sifter into the
sifter housing at an angle so that the drive shaft can
be inserted into the sifter housing. Once the shaft is
inserted all the way, press down on the sifter, opposite
of the shaft, to click it into place.
3
To install the scale: Place the scale on top of the sifter
housing with the digital scale display facing away from
the Stand Mixer, and slightly left of centre. Twist the
scale counterclockwise until it locks into place.
4 To install the ingredient hopper: Align the ingredient
valve with the corresponding notch on the scale, and
lower the hopper onto the scale until fully seated.
1 lb/oz/g
gozlb
Press (On/off), then press (Tare) until the
display reads 0.
WEIGHING AND SIFTING INGREDIENTS
W11221354A.indd 7 6/11/2018 12:12:28 PM

8| USING THE SIFTER+SCALE ATTACHMENT
2
Before adding ingredients to the hopper, be sure the
ingredient valve is in the closed position and swivel
chute is pointed into the mixer bowl or an appropriate
container.
NOTE: If desired, the scale and hopper can sit on the countertop, and ingredients can be
added until the target weight is achieved. The full scale and hopper can then be installed onto
the attachment.
lb/oz/g
gozlb OPTIONAL: Press the lb/oz/g button to choose
between pounds, ounces, and grams. The default
setting is grams.
3 Add your ingredients to the ingredient hopper until
you reach the target weight.
TIP: Make sure your dry ingredients have no large or hard clumps before feeding them
through the sifter. As with any sifter, large or hard clumps may not be broken up during the
sifting process.
4
0 Stir 2 4 6 8 10
Turn on the Stand Mixer to the desired speed, then
open the ingredient valve. The ingredients will be
sifted and flow into the bowl according to the selected
speed.
NOTE: The sifter can operate at any speed, so select
the speed that works best for your recipe.
TIP: If your recipe calls for multiple dry ingredients, press between adding ingredients for
weighing, and stir them in the hopper before opening the ingredient valve.
NOTE: Once you’ve weighed your ingredients, you may turn off the scale at any time by
pressing . The scale will also shut off automatically after 5 minutes of non-use.
USING THE SIFTER+SCALE ATTACHMENT
5 Once sifting appears to be complete, tap the housing
and then the chute to release all residual ingredients.
W11221354A.indd 8 6/11/2018 12:12:29 PM

ENGLISH
TROUBLESHOOTING | 9
TIPS FOR GREAT RESULTS
TROUBLESHOOTING
HELPFUL HINTS
• If the ingredients are sifting faster than
desired, you can use the ingredient valve
to limit the rate at which ingredients flow
into the sifter.
• When releasing ingredients, it may be
necessary to flip the valve back and forth
1-2 times or tap the hopper to ensure all
ingredients are released.
• The maximum capacity of the scale is
1,000g / 2.2lbs / 2lbs 3oz, and the scale
measures in increments of 1g / 0.002lb /
0.05oz.
• Do not feed brown sugar through the
sifter, as it may clog the sifter screen.
• If ingredients become jammed in the
sifter, turn the mixer off and use a spoon
to clear the jam.
• Use dry ingredients only with the
Sifter+Scale attachment.
• Make sure your dry ingredients have
no hard or large clumps before feeding
them through the sifter. As with any sifter,
clumps will not be broken up during the
sifting process.
• The ingredient hopper does not lock
into place. If using a tilt-head Stand
Mixer with the sifter attached, be sure
to remove the ingredient hopper before
lifting the mixer head to avoid the
ingredient hopper tipping or falling off of
the sifter.
• You may wish to place the lid/scale plate
on top of the hopper to reduce dust
when sifting.
While using the Sifter+Scale attachment, you may see the following messages displayed:
Err
The scale has exceeded its weight limit. Remove ingredients from hopper, and try again with a
smaller amount.
- - - Err1
Tare error. Remove ingredients and turn off power. Then, turn power back on. If Err1 is still
present, call customer service.
W11221354A.indd 9 6/11/2018 12:12:29 PM

10 | CARE AND CLEANING
CLEANING THE SIFTER+SCALE ATTACHMENT AND ACCESSORIES
1
The following parts are dishwasher-safe, top rack only:
ingredient hopper, sifter assembly, swivel chute, and
scale plate.
TIP: When placing the ingredient hopper on the rack,
be sure it is lying on its side with the ingredient valve
facing down.
2
Do not immerse the scale or sifter housing in water
or other liquid. Wipe clean with a warm, damp cloth,
and dry thoroughly with a soft cloth before re-use or
storing.
3 To disassemble the sifter assembly: Turn the collar to
the left to loosen and release the screen for cleaning,
if desired.
CARE AND CLEANING
REPLACING THE BATTERIES
The digital scale of your Sifter+Scale attachment is powered by 2 AAA batteries (included).
1 Flip the digital scale over, and use a Phillips-head
screwdriver to remove the screw on the compartment
cover. Lift the compartment cover as shown.
2 Replace the 2 AAA batteries in the compartment.
Make sure to replace the screw when reattaching the
compartment cover.
W11221354A.indd 10 6/11/2018 12:12:30 PM