Kleenmaid IVK61 User manual

REF CONSTRUCTEUR 214
220-240 V 50Hz
Cooking
collection
Instructions for fitting and using
your mixed induction-ceramic
and
Warranty Details
IVK61-600mm Induction-ceramic Cooktop
The best you can own.

2
Congratulations on the purchase of your new appliance.
This appliance has been
designed and manufactured to give you years
of reliable performance.
For best results, carefully read the instructions on how to
install your new appliance. Correct installation will avoid
delays and unnecessary service calls.
Once installation is complete, read this booklet
carefully and get to know the controls and the
features of your new appliance.
We reserve the right to alter the specifications
with no influence on the operation of the
appliance. This instruction manual cannot be
reason for a claim.

In this Manual,
displays safety
instructions
displays tips and hints
Using your hob in complete safety..........................4
Containers.........................................................6-7
Installing your hob in complete safety...........................8
Using your hob in all simplicity.............................10
Preserving and maintaining your hob....................12
Small problems and solutions...............................13
Cooking ........................................................14-15
List of contents
3

4
Using your hob in complete safety
Overheat sensor
•Each unit is equipped with a sensor that continuously monitors the temperature of
the bottom of the pan, so that overheating is impossible (empty saucepan, etc.).
•A sensor continuously monitors the temperature of the components of your hob.
The power output by the hob will automatically be reduced if this temperature
becomes excessive.
Overflow protection
The shutdown of the hob, a special display (symbol shown opposite) and an audible
"beep"* can all be triggered in one of the three following cases:
•An overflow which covers the control buttons.
•A damp cloth being placed on the buttons.
•A metal object being placed on the control buttons.
Clean or remove the object and start cooking once again.
*depending on the model
Residual heat indicator
After intensive use, the cooking zone may remain hot for several minutes.
The letter “
H”
H” is displayed during this period. Do not touch the zones concerned.
Auto-stop system
The "Automatic-Stop" function activates automatically if the user forgets to turn off the
cooker after cooking.
It starts up automatically if ever you forget to turn off after cooking
The letter A is displayed for the heating zone concerned and the hob will bleep for about
2 minutes. The Awill continue to be displayed until any control of the zone in question
is touched. The hob will then bleep twice to confirm your action.
the heating zone
Power used goes out automatically
after:
Between 1....4 8 hours
Between 5....7 2 hours
Between 8....9 1 hour
BIP...BIP
For the hob
For
saucepans

5
Unlocking the appliance
Keypad lock
Your cook top is equipped with a child safety feature which locks it during the use:
- Either when stopped (for cleaning)
- Or during cooking (any operations underway will continue and the displayed settings remain
active).
this case, for safety reasons only the "STOP" button is still usable.
Don't forget to unlock the appliance before reusing it.
Automatic saucepan detection
Your induction hob is able to recognise most recipients.
•Test recipient: place your recipient on one of the rings on power setting 4.
If the display remains unchanged, your recipient is compatible.
If it flashes on and off, your recipient cannot be used with induction.
•You can also check using a magnet.
If it "sticks" to the base of the recipient, then this recipient is compatible with induction.
Removing the recipient from the hob immediately turns off the power to your hob. To
completely turn off the ring you should press on the "Stop" button.
"Small item" safety feature
A small object such as a fork, spoon or a ring placed on your induction hob by itself is not
detected as a pan. The display flashes and there is no output power.
The display goes out after a few seconds.
Pressing any of the buttons activates the display.
Locking the appliance
Choose the specific touch for locking,
press this touch until information is dis-
played on the screen.
Press locking touch until
lights out.
• The appliance is not intended for use by young children without supervision.
• Young children should be supervised to ensure that they do not play with the appliance.

+
-
Induced currents
Electronic circuit
Induction coil
6
For the attention of wearers of pacemakers or other active
implants:
The hob complies with all current standards on electromagnetic interference.
Your induction hob is therefore perfectly in keeping with legal requirements (89/336/CEE directives). It
is designed not to create interference on any other electrical apparatus being used on condition that the
apparatus in question also complies with this legislation.
Your induction hob generates short-range magnetic fields.
To avoid any interference between your induction hob and a pacemaker, the latter must be designed to
comply with relevant regulations.
In this respect, we can only guarantee our own product conformity. Please consult the pacemaker
manufacturer or your doctor concerning its conformity or any possible incompatibility. L
Your induction hob in complete safety
The principles of induction
When your induction hob is switched on and a
heating power has been selected, the electronic
circuits produce induced currents that
instantaneously heat the bottom of the pan that
transfers this heat to the food.
Thus cooking takes place with practically no ener-
gy loss between the induction hob and the food.
If a crack appears in the glass surface, disconnect the appliance immediately to avoid any risk of
electric shock. For disconnecting, remove the fuses or use the cutout switch.
Do not re-use your hob until the glass surface has been changed.
Your hob must never be used as a storage space or cutting surface for any products whatsoever.
When cooking never use aluminium foil and never place products wrapped in aluminium foil or
products deep-frozen in aluminium packs on the hob.
The aluminium will melt and damage your appliance irreparably.
Do not leave empty pans on your hob in case of residual heat or if the hob is turned on by mistake.
Do not connect electrical appliances on plugs close to the hob. Make sure that the power cable is not
in contact with any heating zones.
A steam cleaner must not be used.

7
Induction pan area
You probably already have some suitable pans.
Your induction hob is able to recognize most
types of pans.
Pan test: Place your pan on a zone, for example
at position 4; you know that your pan is compa-
tible if the display does not flash, but if it does
flash then you cannot use this pan for induction
cooking.You can also test it with a magnet: if
the magnet "sticks" to the base of the pan, then
you can use it for induction cooking.
Pans compatible with induction are:
• pans made of enamel coated steel with or
without a non-stick coating.
• cast iron pans with or without enamel coated
base.
An enamelled coated base will prevent the glass
top of your hob from getting scratched.
• stainless steel pans designed for induction
cooking.
Most stainless steel pans (saucepans, stewpans,
frying pans, deep frying pans, etc.) are suitable
for induction cooking if they pass the pan test.
• aluminium pans with special base.
pans which do not have a flat base may be sui-
table, however they must not be badly deformed .
Choose a pan marked with the
logo on its base or packaging to be sure that it is
perfectly suitable for use on your induction hob
under normal conditions of use.
A list of utensils is supplied with these
instructions to help you make your choice.
• Note
Glass, ceramic, earthenware pans, aluminium
pans (without a special base) and copper
pans, and some non-magnetic stainless steel
pans are incompatible with induction cooking.
You will be informed by the flashing display.
You should choose pans with a thick
flat base for uniform cooking (heat is
better distributed).
Using the cooking zones according to the pan (depending on the model)
Ø18 ..... 24 cm
Ø 21 cm
Ø 16 cm
Ø10 ..... 18 cm
Slow cooking (sauces, creams…).
Preparing small quantities or individual
portions…
Multi-service zone
For small pans

8
Vitroceramic pan area
The best way to use your ceramic hob
For easy use, we have provided cooking zones
specially adapted to your needs, nevertheless:
However, higher temperatures may be required
for:
- Large quantities
- Cooking with a non-covered casserole.
- Using a glass or ceramic casserole.
And lower temperatures are required for:
- Cooking food products that tend to burn easily
(start with a low temperature that can always be
increased if possible).
- In case of overflowing
(take the lid off, or remove the pan from the heat,
then lower the temperature).
Energy saving:
To finish off cooking touch the control and
reduce back to 0. Leave the pan in place to use
up all the accumulated heat (which saves
energy).
Use a lid whenever possible to reduce any loss of
heat through evaporation.
Automatic cooking zone temperature adjust-
ment
The radiant cooking zone is self-regulating, It
switches itself on and off so as to remain at the
programmed power. Under these conditions the
temperature remains constant and is correctly
adapted to the food you are cooking.
The frequency of self-regulation depends on the
power being used.
Pans and casseroles must be designed for use with electric hobs.
Use pans with flat bases that have good surface contact with the cooking
zone surface. They must be made out of:
- Stainless steel with a thick tri-metal or "sandwich" bottom.
- In aluminium with a thick smooth bottom.
- In enamelled steel.

9
Installing your hob in complete safety
mini 5 cm
Kit d'isolation (SAV) mini 4 mm
Above an oven
4 cm mini
Ensure that the unit crossbar does not block the air
passage, make a bevel if necessary.
Above a cupboard or drawer unit
Gap MINI 4 mm
If the appliance underneath your hob produces excess heat :
this will be detected by a safety device incorporated into your induction hob. A high temperature will be indicated by a
series of dashes or F7 will appear in the display.
If this happens we suggest you either create an opening in the side of the unit and/or install an insulation kit available
from the After-Sales Dept (ref 75X1652), which will protect your hob from the heat generated beneath it.
Providing the advice on ventilation given above is followed, your hob can be installed above any piece of kitchen
equipment.
Always ensure that the air vents beneath the hob are kept clear.
Your induction hob must always be adequately ventilated.
Opening in the side of the
unit approx 8 cm x 5 cm
Insulation kit (after-sales service)

10
Installing your hob in complete safety
4 cm mini
26 ,5 /56 /75 cm
49 cm
4 cm mini
4 cm mini
Fitting A seal exists for preventing any
humidity getting under the hob.
-Stick the seal under the rim of
the hob and lower the hob into
position on the worktop.
-This seal is supplied in the
sachet; stick it in place beneath
the hob.
Neutral
Earth
Phase
NL
- 220-240 V monophase
fuse 32
Neutral
Earth
Phase 2
Phase 1
NL1 L2
Separate the 2 phase wires L1 and L2
before connecting
Blue
Green/yellow
Black
- 400 V 2N three-phase
fuse : 16 Amp
Green/yellow
Blue
Black
These hobs are delivered with type H 05 VVF power cable (1.5mm²) with 3/5 conductors (including a
green/yellow earth wire), which must be connected to the power supply via a plug that complies with
publication CEI 60083 or an all-pole cut-out unit with contacts that open by at least 3mm.
If the cable is damaged, it must be replaced by the manufacturers, their After Sales Service or another
similarly qualified person for avoiding any possible risk of accident.
When the power is switched on, or after a long power failure, a light
code appears on the control panel. This disappears automatically after
about 30 seconds or as soon as any touch control is touched on the
panel. This is normal, as the display is for use by the after-sales service when required. The user must not
take this into account under any circumstances.If the unit has a 3 phase 400 V2N connection, and is not
working correctly, check that the neutral wire is correctly connected. This precaution should also be taken
for all your other electronic apparatus.
"When installing the cooktop, precautions must be taken to avoid damaging the power cable with the
sharp edges"
The unit must be installed so that the mains plug is easily
accessible.
brown
brown
Connection
58 51
48,8 55,5
6,4
dimensions in cm