Knightsbridge BT14CTEM Instruction Manual

1
INSTALLATION & MAINTENANCE MANUAL
BT14CTEM
230V
50Hz
IP
54
ACCESSORIES LTD ACCESSORIES LTD
ACCESSORIES LTD
ACCESSORIES LTD
02

BT14CT
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
BT14CT
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current building regulations. If in any doubt, please consult a qualified electrician.
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating
of the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•This product is Class II double insulated
•This product is IP54 rated
•This product is non-dimmable
INSTALLATION
•Provide power to the required point of installation. Suitable IP rated junctions boxes should be used
where required
•Remove the diffuser by rotating bezel anti-clockwise (see Fig. 1)
Fig. 1
•Remove the fastening screw securing the LED plate, and open the LED plate (see Fig. 2)
Fig. 2
•Mark the location of the fixing holes, and drill the holes ensuring not to infringe with any gas / water
pipes or electrical cables
•Feed the cable via the rubber grommet to retain IP rating, and secure the baseplate to the surface
BT14CT
These instructions should be read carefully and retained after installation by the end user for future reference and
maintenance.
These instructions should be used to aid installation of the following product:
BT14CT
SAFETY
•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current building regulations. If in any doubt, please consult a qualified electrician.
•Please isolate mains prior to installation or maintenance
•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating
of the circuit cable, fuse or circuit breaker
•Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for
installation
•This product is Class II double insulated
•This product is IP54 rated
•This product is non-dimmable
INSTALLATION
•Provide power to the required point of installation. Suitable IP rated junctions boxes should be used
where required
•Remove the diffuser by rotating bezel anti-clockwise (see Fig. 1)
Fig. 1
•Remove the fastening screw securing the LED plate, and open the LED plate (see Fig. 2)
Fig. 2
•Mark the location of the fixing holes, and drill the holes ensuring not to infringe with any gas / water
pipes or electrical cables
•Feed the cable via the rubber grommet to retain IP rating, and secure the baseplate to the surface
2
These instructions should be read carefully and retained after installation by the end user for
future reference and maintenance.
These instructions should be used to aid installation of the following product:
BT14CTEM
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current building regulations. If in any doubt, please consult a qualified electrician.
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location for installation
• This product is Class II double insulated
• This product is IP54 rated
• This product is non-dimmable
• Mark the location of the fixing holes, and drill the holes ensuring not to infringe with any
gas / water pipes or electrical cables
• Feed the cable via the rubber grommet to retain IP rating, and secure the baseplate to the surface
• Connect the Live (brown), Emergency Live (L1) and Neutral (blue) to the terminals on the terminal block
(see Fig. 3)
• Provide power to the required point of
installation. Suitable IP rated junction
boxes should be used where required
• Remove the diffuser by rotating bezel anti-
clockwise (see Fig. 1)
• Remove the fastening screw securing the
LED plate, and open the LED plate
(see Fig. 2)
Fig. 1
Fig. 2

• Connect the battery to the inverter
• Refasten the LED plate screw
• Choose the required colour temperature by means of the DIP switch (see Fig. 4)
• Reattach the diffuser by rotating
clockwise
• Switch on and check for correct
operation, ensuring the green indicator
LED is illuminated
• We recommend, on commissioning the
installation, a minimum charge period
of 24 hours before carrying out an
emergency duration test
3
•% G,''#+(%(" #%Q&M#%=/),5'CD%?5&(+"#.%Q&M#%=QBC%0'.%V#*()0-%=/-*#C%(,%("#%(#)3&'0-$%,'%("#%(#)3&'0-%
/-,+H%=$##%P&64%WC(
P&6%W%
•% G,''#+(% ("#%/0((#)2%(,%("#%&'M#)(#)%%
•% <# 10$(#'%("#%Q:R%7-0(#%$+)#5%
•% G",,$#%("#%)#E*&)#.%+,-,*)%(#37#)0(*)#%/2%3#0'$%,1%("#%R9F%$5&(+"%=$##%P&64%KC%
%
P&64%K%
•% <# 0((0+"%("#%.&11*$#)%/2%),(0(&'6%+-,+H5&$#%
•% ?5&(+"%,'%0'.%+"#+H%1,)%+,))#+(%,7#)0(&,'D%#'$*)&'6%("#%6)##'%&'.&+0(,)%Q:R%&$%&--*3&'0(#.%
•% ; #%)#+,33#'.D%,'%+,33&$$&,'&'6%("#%&'$(0--0(&,'D%0%3&'&3*3%+"0)6#%7#)&,.%,1%SK%",*)$%/#1,)#%
+0))2&'6%,*(%0'%#3#)6#'+2%.*)0(&,'%(#$(%
%
1*2.-.3 (
!"&$%7),.*+(%3*$(%/#%.&$+,''#+(#.%1),3%("#%+&)+*&(%&1%$*/N#+(#.%(,%0'2%"&6"%M,-(06#%,)%&'$*-0(&,'%)#$&$(0'+#%
(#$(&'64%9))#70)0/-#%.0306#%5&--%,++*)%&1%("&$%&'$()*+(&,'%&$%',(%1,--,5#.%
3&.&2*/ (
!" &$%7),.*+(%$",*-.%/#%)#+2+-#.%&'%("#%+,))#+(%30''#)%5"#'%&(%)#0+"#$%("#%#'.%,1%&($%-&1#4%G"#+H%-,+0-%0*(",)&(&#$%
1,)%5"#)#%10+&-&(&#$%#I&$(%
91%("#%/0((#)&#$%"0M#%/##'%-#1(%&'%0%.&$+"0)6#.%$(0(#%1,)%0%-,'6%7#)&,.%,1%(&3#D%5#%)#+,33#'.%("0(%,'#%,)%3,)#%
+"0)6#%0'.%.&$+"0)6#%+2+-#$%0)#%7#)1,)3#.D%(,%)#$(,)#%("#%/0((#)2%(,%&($%1*--%+070+&(2%
!"#%/0((#)&#$%&'%("&$%-*3&'0&)#%0)#%V&+H#-%G0.3&*3%0'.%3*$(%/#%.&$7,$#.%,1%+,))#+(-24%F-#0$#%+,'(0+(%("#%-,+0-%
0*(",)&(&#$%1,)%("#%.&$7,$0-%,1%("&$%(,I&+%50$(#%
G-#0'%5&("%0%$,1(%.)2%+-,("%,'-2D%.,%',(%*$#%066)#$$&M#%+-#0'&'6%7),.*+($%,)%$,-M#'($%5"&+"%302%.0306#%("#%
7),.*+( %
1*22*.", %
!"&$%7),.*+(%"0$%0%50))0'(2%,1%W%2#0)$%=#I+-*.&'6%/0((#)2C%1),3%.0(#%,1%7*)+"0$#4%P0&-*)#%(,%&'$(0--%("&$%7),.*+(%&'%
0++,).0'+#%5&("%("#%+*))#'(%#.&(&,'%,1%("#%9::%;&)&'6%<#6*-0(&,'$D%&37),7#)%*$#D%,)%)#3,M0-%,1%("#%/0(+"%+,.#$%
5&--%&'M0-&.0(#%("#%50))0'(24%91%("&$%7),.*+(%$",*-.%10&-%5&("&'%&($%50))0'(2%7#)&,.%&(%$",*-.%/#%)#(*)'#.%(,%("#%7-0+#%
,1%7*)+"0$#%1,)%0%1)##%,1%+"0)6#%)#7-0+#3#'(4%TQ%X++#$$,)&#$%.,#$%',(%0++#7(%)#$7,'$&/&-&(2%1,)%0'2%&'$(0--0(&,'%
+,$($%0$$,+&0(#.%5&("%("#%)#7-0+#3#'(%7),.*+(4%Y,*)%$(0(*(,)2%)&6"($%0)#%',(%011#+(#.4%TQ%X++#$$,)&#$%)#$#)M#%("#%
)&6"(%(,%0-(#)%7),.*+(%$7#+&1&+0(&,'%5&(",*(%7)&,)%',(&+#4%
%
Neutral (blue)
Live (brown)
Emergency Live
Fig. 3
•Connect the Live (brown) and Neutral (blue) to the terminals on the terminal block (see Fig. 3)
Fig. 3
•Refasten the LED plate screw
•Choose the required colour temperature by means of the DIP switch (see Fig. 4)
Fig. 4
•Reattach the diffuser by rotating clockwise
•Switch on and check for correct operation
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the
warranty. If this product should fail within its warranty period it should be returned to the place of purchase for a
free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated
with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter
product specification without prior notice.
Neutral (blue)
Live (brown)
Fig. 4
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist
If the batteries have been left in a discharged state for an extended period, we recommend that one or more
charge and discharge cycles are completed which should help to restore the battery capacity
The batteries in this luminaire are Nickel Cadmium and must be disposed of correctly. Please contact the
local authorities for the disposal of this toxic waste
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product
WARRANTY
This product has a warranty of 3 years (excluding battery) from date of purchase. Failure to install this
product in accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of
the batch codes will invalidate the warranty. If this product should fail within its warranty period it should
be returned to the place of purchase for a free of charge replacement. ML Accessories does not accept
responsibility for any installation costs associated with the replacement product. Your statutory rights are
not affected. ML Accessories reserve the right to alter product specification without prior notice.

4
TESTING FOR EMERGENCY LUMINAIRES
Recommended routine test procedure in accordance with BS5266
• Daily check – check LED charge indicator is illuminated
• Monthly functional test – simulate a mains supply failure for approx. 30 seconds by operation of key
switch or switching off circuit breaker. Ensure normal supply is restored after test and ensure charge
indicator is illuminated
• Annual three hour duration test - simulate a mains supply failure for a three hour continuous test
by operation of key switch or switching off circuit breaker. Ensure normal supply is restored after test and
ensure charge indicator is illuminated
• If the luminaire fails any of the above tests, please contact a qualified electrician
Please note: the Switched Live should not be re-energised during the emergency test
TEST RECORD SHEET
INITIAL COMMISSIONING
3 HOUR TEST
SIGNED DATE
MONTH TEST
FIRST YEAR SECOND YEAR THIRD YEAR FOURTH YEAR FIFTH YEAR
SIGNED DATE SIGNED DATE SIGNED DATE SIGNED DATE SIGNED DATE
1 FUNCTIONAL
2 FUNCTIONAL
3 FUNCTIONAL
4 FUNCTIONAL
5 FUNCTIONAL
6 FUNCTIONAL
7 FUNCTIONAL
8 FUNCTIONAL
9 FUNCTIONAL
10 FUNCTIONAL
11 FUNCTIONAL
12 3 HOUR
Installed by: Installation date:
Contact number:
ML Accessories Limited
LU5 4LT
www.mlaccessories.co.uk DCOCT18_V1
ACCESSORIES LTD ACCESSORIES LTD
ACCESSORIES LTD
ACCESSORIES LTD