Knightsbridge LWALL1A Instruction Manual

INSTALLATION & MAINTENANCE MANUAL
LWALL1A / LWALL2A / LWALL3A

These instructions should be read carefully and retained after installation by the
end user for future reference and maintenance.
These instructions should be used to aid installation of the following products:
LWALL1A / LWALL2A / LWALL3A
GENERAL INSTRUCTIONS
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring
Regulations (BS7671) and current Building Regulations. If in any doubt, consult a
qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed
the rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress Protection) rating of this luminaire when deciding the location
for installation
• This product is Class I and must be earthed
• This product series is IP65 rated

INSTALLATION
Note - If this luminaire is being used in conjunction with an external PIR or sensor, please
confirm with the manufacturer of the sensors that they are compatible with LED luminaires
• Provide power to the required point of installation (refer to BS7671 for correct cabling
methods). Suitable IP rated junction boxes should be used where required
• Round cable should be used for the mains supply. The use of flat cable will cause water
ingress to the fitting
• Remove the baseplate from the luminaire by loosening the screws on the side
• Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring
not to infringe with any gas/water pipes or electrical cables
• Feed the mains cable through the
rubber grommet to retain IP rating,
and secure the baseplate to the
surface. Rubber washers or sealant
should be applied around the
screw heads to prevent water
ingress (see Fig. 1)
Fig. 1
N
L
1
2
3
4
5678

• Connect the luminaire to the mains supply ensuring the correct polarity is observed: Live
(brown), Earth (green/yellow), Neutral (blue) (see Fig. 2)
• Refit the luminaire to the baseplate and tighten
• Switch on and check for correct operation
Fig. 2
•Connect the luminaire to the mains supply ensuring the correct polarity is observed: Live (brown),
Earth (green/yellow), Neutral (blue) (see Fig. 2)
Fig. 2
•Refit the luminaire to the baseplate and tighten
•Switch on and check for correct operation
WARNING
This luminaire must be disconnected from the circuit if subjected to any high voltage or insulation resistance
testing. Irreparable damage will occur if this instruction is not followed.
GENERAL
The LED lamps fitted in this product are non-replaceable. The product should be recycled in the correct manner
when it reaches the end of its life. Check local authorities for where facilities exist.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not
use aggressive cleaning products or solvents which may damage the product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is not suitable for installation in or near a coastal or marine environment.
This product is non-dimmable.
WARRANTY
This product has a warranty of 2 years from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period it should be returned to the place of
purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
AVAUG20_V1

WARNING
WARRANTY
GENERAL
This product must be disconnected from the circuit if subjected to any high voltage or
insulation resistance testing. Irreparable damage will occur if this instruction is not followed.
This product is not suitable for installation in or near a coastal or marine environment.
This product has a warranty of 2 years from date of purchase. Failure to install this product
in accordance with the current edition of the IEE Wiring Regulations (BS7671), improper
use, or removal of the batch code will invalidate the warranty. If this product should fail
within its warranty period, it should be returned to the place of purchase for a free of
charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML
Accessories reserve the right to alter product specification without prior notice.
The light source of this luminaire is not replaceable; when the light source reaches its end of
life the whole luminaire should be replaced.
Clean the external surfaces with a damp cloth using a mild solution of detergent and warm
water only, do not use aggressive cleaning products or solvents which may damage the
product.
Do not use any source of high-pressure washers to maintain or clean this luminaire.
This product is non-dimmable.
This product should be recycled in the correct manner when it reaches the end of its life.
Check local authorities for where facilities exist.

AVOCT21_V2
-25
~35 °C
TA
02
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS