Kohler ACCLIV 33088T-4-CP User manual

INSTALLATION INSTRUCTIONS
安装说明书
Shower Column - Hose Connection
**订购时请说明颜色编号
**Color code must be specified when ordering
SERVICE PARTS
零 件 图
1461297-T2-A 1
1461297-T2-A 4
BEFORE YOU BEGIN
安装之前
33096T-4 双花洒淋浴柱 - 软管连接
33088T-4 三出水淋浴柱 - 软管连接
33096T-4 双花洒淋浴柱 - 软管连接
33088T-4 三出水淋浴柱 - 软管连接
Shower Column - Hose Connection
安装尺寸 ROUGH-IN DIMENSIONS
33096T-4 33088T-4
79680
1226888**
Ø110
G1/2˝
239
248
1414921**
833438
3008523
1414936**
1420675
1292053
33088T-4:
1414937**
33088T-4:
1285497**
33088T-4:
3015846
1125667**
1316402**
1277170**
1277169**
1218659
864985
871363
33096T-4:870721
33096T-4:864922**
G1/2˝ G1/2˝
75
83
786
781~981
1077~1277
装修好的地面
Finished Floor
Ø254
400
870992
1436004**
870921
870992
1121285
1196609**
832751
1196622**
1196621**
1196610
1196621**
1456331**
832751
832751
832751
1081338
1196610
1061576
1061576
870921
1046290
1433501**
G1/2˝
G1/2˝
500
1500
G1/2˝
G1/2˝
1030624
77420
1154793**
1248781**
CP:1443647**
AF/BN:1455615**
CP:1443626**
AF/BN:1455616**
CP:1456330**
AF/BN:1456492**
珂灵
ACCLIV
珂灵
ACCLIV
150±15
59~64 91
Ø66
G1/2˝
G1/2˝
97
10º
150±15 Ø66
G1/2˝
65~70 105
G1/2˝
114
推荐高度
Recommended Height
1200~1300
All information is based on the latest product information
available at the time of publication. Kohler Co. reserves the
right to make changes in product characteristics, packaging,
or availability at any time without notice.
Please leave these instructions for the consumer.
They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage. Replace as
necessary. Shut off the water supplies to the fitting.
3. Observe local plumbing codes.
4. The minimum inlet water pressure for diverter is
0.05MPa(0.5bar).
5. Recommended minimum working pressures is
0.1MPa(1bar).
6. The highest working pressure for handshower &
showerhead is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar),
a pressure reducer is needed. The highest water and
environment temperature is 60°C. Please keep handshower,
showerhead and shower arm away from heater, or it may
become damaged and cause injury to the user.
所有的资料是按最新出版的产品资料编写而成。科勒公
司保留任何时候不经通知即可改变产品特性、包装或产
品可供类型的权利。
说明书包括重要的安装、保养及清洁方面的内容，请把
这些资料交给用户阅读。
注意事项：
1.彻底冲洗供水管，以清除管路中杂质。
2.检查供水管路有无损坏。如需要进行替换。切断供水
管路。
3.遵守当地管路安装条例。
4.切换器正常工作的最小压力为：0.05MPa(0.5bar)。
5.推荐最小工作压力：0.1MPa(1bar)。
6.花洒最高工作压力：0.5MPa(5bar)。水压超过
0.5MPa(5bar)须安装减压阀。花洒最高工作温度及环境
温度：60°C。请特别注意花洒同花洒连接的臂管须远
离浴霸，否则可能损坏花洒及其密封件，甚至对使用者
造成伤害。

安装步骤 INSTALLATION
1461297-T2-A 3
1461297-T2-A 2
How to Install the Faucet
To perform installation, installer must provide
G1/2″ female supply fittings(1), spaced 150mm
apart and horizontal. The supply fittings should
be vertical and not beyond the finished wall. Hot
supply pipe must be located on the left.
Flush the water supply pipes thoroughly to
remove debris. Install the two offset connectors
(2) into the hot and cold supply pipes. Use
appropriate thread sealants or thread tape on
pipe threads.
Adjust the center-to-center distance between the
connectors to 150mm horizontally. They should
extend 27~32mm beyond the finished wall.
Thread the escutcheons(3) onto the connectors
until they are against the wall.
Put the washers(4) into the nuts(5). Thread and
tighten the nuts to the connectors. NOTE: When
tighten the nuts, use strap wrench or soft cloth
between product and regular wrench to protect
the finish.
如何安装水龙头
为安装顺利，G1/2″内螺纹管道配件(1)应
已装好，预留150mm的间距，保持水平。
管道配件要垂直并且不能突出装修好的墙
面。热供水管装在左边。
彻底冲洗供水管以清除管路中的杂质。在
两个接头(2)涂上螺纹密封胶或缠绕足以密
封的密封胶带，旋入冷热水管中。
调节两个接头使其中心距离为150mm，并
保持同一水平线，凸出墙面27~32mm。
把装饰罩(3)旋在接头上使其紧贴墙面。
把垫片(4)放入水龙头螺母(5)内，把螺母
旋到接头上并拧紧。注意：在锁紧螺母时
须用带状扳手或用软布垫在普通扳手和螺
母之间，以保护镀层表面。
150mm
27~32mm
Cold
Hot
热
冷
2
1
3
4
5
How to Install the Shower Column
Select a location in vertical wall to install shower
column according to rough-in dimensions. Drill
the lower hole according to anchors’(6) diameter
and lower base(8-1) position in the finished wall
(NOTE: The arrow in the base is upward). Press
anchors into the hole, secure the base by the
screw(7).
Rehearse the slide bar kit(9) installation for the
upper base(8-2) mounting location determination.
Slide the tube joint(10) onto the slide bar kit, and
connect them to the base(NOTE: The arrow in
the base is up). Install the screws(12) into the
tube joint with the hex wrench(11), and tighten
them.
Place the slide bar and the body against the
finished wall. Connect the lower base and the
slide bar kit. Position and tighten them with a hex
wrench. Mark the hole of upper base(8-2) with a
pencil. Uninstall the slide bar kit and upper base.
NOTE: Don’t lose the screws.
Drill holes on the mark. Press the anchors into
the holes. Secure the upper base by the screws.
Install the diverter kit(13) to the slide bar kit.
Tighten the screws(15) with a hex wrench.
Reinstall the slide bar kit with escutcheons(14) to
the bases. Tighten the screws with a hex wrench.
Screw the escutcheons to the bases until against
the finished wall. Adjust the bracket(16) to the
right position.
Install the tube kit(17) into the slide bar kit.
Install the nut(18) onto the tube kit with soft cloth
between internal hole of the nut and the tube kit.
Then screw the nut onto the slide bar kit with
strap wrench or soft cloth between the nut and
regular wrench.
如何安装淋浴杆
根据安装尺寸在垂直面的墙壁选一合适的
位置来安装淋浴杆。根据胀塞(6)的直径和
下底座(8-1)的安装位置在垂直墙壁上钻孔
(注意：底座上的箭头朝上)。将胀塞塞入
孔中，用螺钉(7)固定下底座。
试装滑杆组件(9)，以确定上底座(8-2)的安
装位置。将连接管(10)套在滑杆组件接头
上，并与底座连接(注意：底座上的箭头
朝上)。将螺钉(12)装入连接管，并用六角
扳手(11)锁紧。
将滑杆紧贴墙壁放置。连接下底座与滑杆
组件，并用螺钉固定。调整好滑杆及各组
件朝向，用铅笔标记上底座(8-2)孔位。拆
下滑杆组件和上底座。注意：切勿弄丢螺
钉。
根据胀塞直径在标记处钻孔。将胀塞塞入
孔中，用螺钉固定上底座。将切换器(13)
装到滑杆组件上，用六角扳手锁紧螺钉
(15)。将滑杆组件连同装饰罩(14)装在底
座上，用六角扳手锁紧螺钉。将装饰罩旋
紧到底座上直至接触墙面。调整托架(16)
到合适位置。
将弯管组件(17)装入滑杆组件。用软布垫
在螺母(18)的里孔和弯管组件之间，将螺
母套入弯管组件。然后用带状扳手或用软
布垫在普通扳手和螺母之间，将螺母旋紧
到滑杆组件上。
6
712
8-2
6
7
12
8-1
15
13
14
14
17
18
16
10
11
9
使用说明 OPERATION INSTRUCTIONS
Lift the handle gently. Turn clockwise for hot water,
turn counter-clockwise for cold water. Press the
button of the diverter to switch to the showerhead
or handshower mode.
For 33088T, water flows out from spout when
faucet diverter is in the normal position; Lift the
diverter gently, turn it clockwise, the showerhead
or handshower works. Shut off the faucet, turn the
diverter counter-clockwise until it stops.
The products can automatically discharging the
residual water in the column. It will automatically
discharge the residual water after each bathing.
Turn the handle(31) behind the column to turn on
or turn off this function (as figure shown).
清洗说明 CLEANING INSTRUCTIONS
适用于所有加工处理过的表面：以中性肥皂水清洗镀层
表面，再以干净软布彻底擦干整个表面，许多清洁剂比
如氨水、去污粉及洁厕灵等，会对电镀表面造成伤害，
切忌使用。
有磨损性的清洁用具或清洁剂也不可使用于科勒牌的水
龙头及其配件上。
All Finishes: Clean the finish with mild soap and warm water.
Wipe entire surface completely dry with clean soft cloth.
Many cleaners may contain chemicals, such as ammonia,
chlorine, toilet cleaner etc. which could adversely affect the
finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets
and fittings.
如何安装手持花洒和软管
打开供水源及龙头，提起切换器(27)以
冲掉杂质。
将垫片(19)分别放到500mm软管(20)的
两端。用软管(20)连接出水口(21)及切换
器接头(22)。
根据需要将限流器(26)塞入手持花洒(23)
进水口。将滤网垫片(19)放到1500mm软
管(25)的两端，用软管(25)连接接头(24)
与手持花洒。
How to Install the Handshower and
Hose
Lift the handle and diverter(27), run hot and cold
water for one minute to remove any debris.
Put two washers(19) in each end of the 500mm
length hose(20). Connect the outlet(21) and
connector(22) with the hose(20).
Put the regulator(26) into the handshower(23) if
needed. Put two washers(19) into each end of the
1500mm length hose(25). Connect the connector
(24) and handshower with the hose(25).
安装结果检查
INSTALLATION CHECKOUT
Ensure all connections are tight. Ensure the handle
is in the off position. Turn on the main water supply,
and check for leaks. Repair as needed.
Only for 33088T, remove the aerator(32) with coin.
Turn on the faucet. Run hot and cold water for
about one minute to remove any debris. Check for
leaks. Remove any debris from the aerator. Shut
off the faucet. Reinstall the aerator.
检查并确保所有衔接螺母都已拧紧。确
保把手在关闭位置。打开主供水源，检
查是否有漏水。如有漏水，修理之。
对于33088T，用硬币拆下起泡器(32)。
打开水龙头冷热水让水流出约一分钟以
清除杂质，检查渗漏。冲洗起泡器，关
闭水龙头，重新装回起泡器。
32
如何安装头顶花洒
装头顶花洒(28)之前 ，按压切换器(13)按
钮
打开水源冲掉管路中的杂质。
根据需要将限流器(29)塞入头顶花洒进
水口。
将垫片(30)放入花洒内，连接弯
管组件及
头顶花洒， 并用带状扳手锁紧
花洒。
How to Install the Showerhead
Press the diverter (13) button, run hot and cold
water for one minute to remove any debris before
the showerhead(28) is installed.
Put the regulator(29) into the showerhead if
needed. Put the washer(30) into the showerhead.
Connect the showerhead to the tube kit, and
tighten the showerhead with strap wrench.
30
29
28
22
27
25
23
24
20
19
21
26
31
ON
OFF
将把手轻轻提起，顺时针转为热水，逆
时针转为冷水。淋浴柱切换器上的按钮
可以切换到头顶花洒或手持花洒出水。
对于33088T，龙头切换器处于正常位置
时出水口出水；将切换器轻轻提起，顺
时针旋转切换器，头顶花洒或手持花洒
出水。关闭龙头，逆时针旋转切换器到
停止位置。
本产品具有自动排出淋浴柱内残留水的
功能，每次使用完头顶花洒后自动排出
残留水，转动淋浴柱切换器后方把手
(31) 可开启或关闭此功能(如图所示)。