Kohler FLEXISPACE 2.0 K-23790T User manual

-1-
1044886-T01-A
FLEXISPACE 2.0 2.0
INSTALLATION INSTRUCTIONS
SIDE CABINET
K-23790T/K-23791T/K-23792T
BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
·
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
Ensure all electric work has completed before furniture
installation.
Make sure the finished wall is straight and plumb, and the
floor is flat and perendicular to the finished wall.
Remove any moldings that may inhibit the vanity from
being flush against the finished wall.
It is recommended that the door(s) and shelf be removed
from the cabinet before beginning the cabinet installation.
Doing so will ease the installation process. Refer to the
sections contained in this guide for proper removal.
It is mainly made up of high quality E1 grade wood-based
panel of high quality, non-copper laminated glass mirror
and environmental friendly LED light. Its harmful gas
emission is less than 1.5mg/l.
Before installation carefully inspect the new fixture for any
signs of damage.
·This product complies with GB 24977-2010.
·
·
·
·
·
·
·
·
E1
LED
1.5mg/l
·GB 24977-2010
ORDERING INFORMATION
This installation covers the following products in the
FLEXISPACE 2.0 Side Cabinet range:
FLEXISPACE 2.0 Open Side Cabinet................K-23790T
FLEXISPACE 2.0 Close Side Cabinet ...............K-23791T
FLEXISPACE 2.0 Full-Length Mirror..................K-23792T
2.0
2.0 ............................................K-23790T
2.0 ............................................K-23791T
2.0 ....................................................K-23792T
SAFETY WARNINGS
Kohler products are precision-engineered and should give
continued superior and safe performance, provided:
1. They are installed, commissioned, operated and
maintained in accordance with the recommendations given
in this Manual.
2. Periodic attention is given, as necessary, to maintain the
product in good functional order. Recommended
guidelines are given in the section.
Carefully inspect the new fixture for any signs of damage.
When installing Kohler Products, manufacturers guidelines for
power tool safety should be followed.
MAINTENANCE
1.
2.
CHANGSHU KOHLER LTD., SOUTHEAST ECONOMIC DEVELOPMENT ZONE,
CHANGSHU, JIANGSU PROVINCE, CHINA POST CODE 215500
215500
©
©
Copyright Kohler China Investment Co., Ltd. 2020
2020
1419266-T01-A

-2-
TOOLS AND MATERIALS
·
·
·
·
·
·
·
Pencil
Measuring Tape
Level
Safety Glasses
Drill
Screwdrivers
8mm Drill Bit
·
·
·
·
·
·
·8mm
ROUGHING-IN
UNIT : mm
Reference Value
Kohler reserves the right to change marked dimensions without prior notice.
125
145
145
280
280
280
800
800
1600
K-23790T
FLEXISPACE 2.0 Open Side Cabinet
2.0
K-23791T
FLEXISPACE 2.0 Close Side Cabinet
2.0
K-23792T
Full-Length Mirror
FLEXISPACE 2.0
2.0
Fig.1
1
1419266-T01-A

-3-
INSTALLATION
WARNING:
CAUTION!
Note:
Risk of property damage. The side cabinet is
heavy. Obtain sufficient help to lift or move it. It is suggested
to remove the door panel before hanging the side cabinet
(Please place the door carefully). If not, please make sure to
press the door panel firmly when lifting it. Otherwise, the door
panel may open by itself, which may affect installation or
cause damage.
1. Decide on the location of the side cabinet.
2. Mark the positions of the wall hanging anchors on the wall
according to the dimensions given.
Make sure that you avoid hidden cables and
pipes when you drill holes in the wall. For hollow wall, please
choose specialized expanding dowels and screws. The
expanding dowels and screws supplied are for solid wall only.
Side cabinet and full-length mirror are for combination
installation. The open side cabinet can be hung vertically or
horizontally, as shown.
A. Install The Side Cabinet
(
)
1.
2. 2
3
A.
Fig.2
2
Fig.3
3
Cabinet Wall
Bolt Holes
Cabinet Wall
Bolt Holes
Cabinet Outline Cabinet
Outline
98.5
98.5
20 20
603
800
140 140
280
Bracket
35
1565
1600
280
Suggested Dimension
1100~1200
Suggested
Dimension
300~400
Vertically
Horizontally Combination
Installation
1419266-T01-A

3. Using a suitable drill, drill the holes for the wall hanging
brackets.
4. Insert the plugs into the wall.
5. Apply a washer to the screw before tightening it.
6. Use a spirit level to ensure the cabinet is level. Make sure
the side cabinet has been fixed firmly on the wall.
3. 4
4.
5.
6.
-4-
Fig.4
4
Cabinet
Back
8
B.
1. 2
B. Installation The Full-length Mirror
1. Mark the position of hanged bracket according to
dimensions as illustrated, and loosen the suspension hook
of full-length mirror cabinet.
Avoid the cables and pipes inner set when
drilling in the wall.
Different types of bolts are required for different
decoration boards. Please apply suitable bolts and plugs.
Caution!
Note:
2.
3.
2. Drill holes for fixing the bracket. Using a level, ensure that
the hanged bracket is level.
3. Use suitable plugs and bolts, and fix the hanged bracket on
the wall.
1419266-T01-A

4. 5
4. Hang the cabinet on the wall, and position
the suspension on the hanged bracket. See Fig.5.
full-length mirror
Fig.5
5
Fig.6
6
Cabinet
Back
-5-
5. Set the cabinet onto the wall bracket. Be
sure the cabinet adjusted level and the back board of
cabinet appressed to the wall by adjusting the screws of
wall clips.
6. Mark the wall through one hole at the corresponding
positions as illustrated in Fig 5.
7. Dismount the cabinet and put aside. Drill
holes at the marked position.
8. Insert the plugs into the wall.
See Fig.5.
Avoid the cables and pipes inner set when
drilling in the wall.
Different types of bolts are required for different
decoration boards. Please apply suitable bolts and plugs.
Caution!
Note:
full-length mirror
full-length mirror
5.
5
6. 5
8.
7.
9. Set the full-length mirror cabinet onto the brackets, adjust
the screw of the suspension patch with cross screwdriver
to make the cabinets level and at the same height. Upper
screws are for forward and backward adjustment and lower
screws are for upward and downward adjustment. Cover
the hole with the hole cap.
9.
1419266-T01-A

-6-
Fig.7
7
Fig.9
9
Fig.8
8
10.
7
11.
10. Apply a washer to the screw before tightening it. Make
sure the washbasin cabinet has been fixed firmly on the
wall.
11. Fix the screws of the handle with screwdriver or pistol drill.
See Fig.7.
D.
9
D. Door Adjustments
Refer to the illustration and note the screwdriver location for
the desired adjustment.
C. 8C. Adjust position of the adjustable shelf ad shown.
Bracket
Clip
Horizontal
Depth Vertical
E.
1.
2.
3.
E. Removal
1. Apply a small amount of leverage to the door with one
hand to keep the door in the full open position.
2. Press the clip to release the hinge from its bracket.
3. Move the door forward to slide the hinges off the brackets.
12345
1419266-T01-A

-7-
F.
1.
2.
3.
4. 10
F. Door Reinstallation
NOTE: To ease installation, get assistance supporting the
door.
1. Align the hinge hooks with the slot of the top bracket.
2. Slide the hinge onto the top bracket.
3. Clip the hinge onto the bracket to secure.
4. Repeat for the lower hinge.
Fig.10
10
Slot
Hook
Bracket
USER MAINTENANCEUSER MAINTENANCE
1.
2.
3.
4.
5. PU .
6. .
7.
8.
Cleaning
Caution! Risk of product damage.
1.
2.
3.
4.
5. The cabinet door and interior are constructed of mirror and
aluminum. Use only a damp cloth to clean. Spray the cloth,
not the mirror when cleaning. Mirrors are damaged by the
use of ammonia or vinegar based cleaners. Rubbing
alcohol can be used for stubborn stains.
6. Use no abrasive cleansers on any part of the cabinet.
7. The white frame should be cleaned with a damp cloth only.
8. If any fixtures caused by abnormal reasons, Kohler China
can supply paid replacement for service parts caused by
abnormal reasons as shown in the service parts page in
the limited duration of warranty.
Many cleansers contain abrasive and chemical substance
which is not suitable for cleaning stainless steel, enamel,
plating or plastic products. You may use mild cleansers or
soaps to clean the surfaces. Wipe any splashes of cleaner
solutions from the surface with clean soft cloth.
Maintain ventilation in the bathroom, and separate the dry
area from the damp one if conditions permit. Try to open
the door and windows of the bathroom and maintain good
ventilation.
Kohler bathroom cabinet are dealt with strict procedures
for damp-proof, whose good damp-proof function ensures
good performance even in bathroom of huge humidity. Yet
do not splash and pour water directly on the bathroom
cabinet. Make sure that the bathroom is not over damp
and wipe any splashes from surfaces immediately.
Maintenance of door board: Clean and wipe door board
regularly, and wipe the condensation vapor with dry and
soft cloth.
1419266-T01-A