Kohler NEW IPSWICH K-13987T-A User manual

-1-
215500
, 2012
Copyright Kohler China Ltd., 2012
NEW
INSTALLATION INSTRUCTIONS
WASHBASIN CABINETS
K-13987T-A/K-13989T-A
IPSWICH
BEFORE YOU BEGINBEFORE YOU BEGIN
·
·
·
·
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information-
Turn off the water supply.
The pluming installation must comply with Water Supply
Regulations/Bye-laws, Building Regulations or any
particular regulations and practices, specified by the local
water company or water undertakers. The installation
should be carried out by a plumber.
Before installation carefully inspect the new fixture for any
signs of damage.
please leave instructions for the
consumer.
IPSWICH bathroom cabinet adopts E1 grade wood-based
panel of high quality, and with further processing, its
harmful emissions will be less than 1.5mg/L.
·
·
·
·
·
·
·
-
E1
1.5mg/L
ORDERING INFORMATION
This installation covers the following products in the NEW
IPSWICH range:
NEW IPSWICH 900mm
Washbasin Cabinet ..................................K-13987T-A
NEW IPSWICH 1200mm
Washbasin Cabinet ..................................K-13989T-A
900mm
.......................................................K-13987T-A
1200mm
.......................................................K-13989T-A
SAFETY: WARNINGS
Kohler products are precision-engineered and should give
continued superior and safe performance, provided:
1. They are installed, commissioned, operated and
maintained in accordance with the recommendations given
in this Manual.
2. Periodic attention is given, as necessary, to maintain the
product in good functional order. Recommended
guidelines are given in the section.
Carefully inspect the new fixture for any signs of damage.
When installing Kohler Products, manufacturers guidelines for
power tool safety should be followed.
MAINTENANCE
1.
2.
1199569-T01-A

-2-
ROUGHING-IN
UNIT : mm
K-13987T-A
900mm Washbasin Cabinet
900mm
K-13989T-A
1200mm Washbasin Cabinet
1200mm
INSTALLATION
A. Install Washbasin Cabinet
Install the services.
Hot (H) and Cold (C) inlets must be connected to the correct
inlet pipes.
Install the drain in accordance with the manufacturer's
instructions.
We suggest using P-trap drain. Connect P-trap pipe with
washbasin drain.
Make sure a watertight seal exisits on all
washbasin drain connections.
Provide access to the plumbing
connections for future plumbing maintenance.
The hot and cold water supplies must be installed
with isolating valves.
CAUTION !
CAUTION !
NOTE
A.
(H) (C)
P
Fig.2
2
Reference Value
900
580
820
1200
580
820
Kohler reserves the right to change marked dimensions without prior notice.
Fig.1
1
1199569-T01-A

-3-
Fig.3
3
1. 4 3
1. Screw out four adjustable feet (see Fig.3). Place the
cabinet at a desired position in the bathroom, and then
adjust the four adjustable feet to put the cabinet in place.
2. Mark the wall through two holes at the corresponding
positions. As Fig 4.
2. 4
8
Fig.4
4
3. Dismount the washbasin cabinet and put aside. Drill holes
at the marked position.
4. Insert the plugs into the wall.
5. Apply a washer to the screw before tighten it. Make sure
the washbasin cabinet has been fixed firmly on the wall.
6. Assemble the handles as illustrated in Fig 5.
CAUTION!
NOTE:
Avoid the cables and pipes inner set when
drilling in the wall.
Different types of bolts are required for different
decoration boards. Please apply suitable bolts and
Plugs.
3.
4.
5. 8
6. 5
Go up
Go down
1199569-T01-A

B
1. ,
2.
3.
4.
B. Finish Installation
1. Install the faucet and lavatory in accordance with the
manufacturer s instructions.
2. Connect the hot and cold water supplies.
3. Attach the waste, and tighten securely.
4. Turn on the hot and cold water valves and check the
supply connections for any leaks.
a. (P )
/
a. Inwall drainage (P-Trap)
Please install the drain assembly and faucet as shown.
Please set the water supply and drainage position
according to the suppliers instructions. You can adjust the
height of shelf to fit the drain assembly.
Door
Faucet
Supply Lines
Shut-off Valve
Drain Assembly
Back Board
6
Fig.6
Fig.5
5
1199569-T01-A

b. S
b. Floor drainage (S-Trap)
Please install the drain assembly and faucet as shown.
Please set the water supply and drainage position
according to the suppliers instructions. You can adjust the
height of shelf to fit the drain assembly.
-5-
NOTE For installation of 1200mm cabinet, please first
remove the drawers and reinstall them onto rails after
fixing the drainage (see Fig.8).
Faucet
Supply Lines
Door
Shut-off Valve
Back Board
Ripple Pipe
Outlet
7
Fig.7
1200mm
8
Fig.8
8
Rail
Step 1
1
Step1
1
Step2
2
Step2
2
Step 1
1
5.
6. , 9
7.
5. Run water into the washbasin or vanity top, and check the
drain connections for any leaks.
6. Adjust all hinges of door in three-way as illustrated in Fig 9,
and make sure that the door is level and neat. Clearance
between doors is even, and that between doors and
cabinet is tight.
7. Place the hinge cover and plastic cover.
1199569-T01-A