Kohler MAXISPACE K-96103 User manual

-1-
BEFORE YOU BEGINBEFORE YOU BEGIN
INSTALLATION INSTRUCTIONS
CABINET
K-96103T/K-96104T
MAXISPACE
·
·
·
·
·
·
·
·
Please read these instructions carefully to familiarize
yourself with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information in these instructions is based upon the
latest product information available at the time of
publication. Kohler China. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning, and
warranty information-
Turn off the water supply.
The pluming installation must comply with Water Supply
Regulations/Bye-laws, Building Regulations or any
particular regulations and practices, specified by the local
water company or water undertakers. The installation
should be carried out by a plumber.
Before installation carefully inspect the new fixture for any
signs of damage.
This product complies with GB 24977-2010.
please leave instructions for the
consumer.
MaxiSpace cabinet adopts E1 grade wood-based panel of
high quality, and with further processing, its harmful
emissions will be less than 1.5mg/L.
·
·
·
·
·
·
·
·
-
E1
1.5mg/L
GB 24977-2010
ORDERING INFORMATION
This installation covers the following products in the
MaxiSpace range:
MaxiSpace Cabinet 600mm ...............................K-96103T
MaxiSpace Cabinet 900mm ...............................K-96104T
600mm.............................................K-96103T
900mm.............................................K-96104T
SAFETY WARNINGS
Kohler products are precision-engineered and should give
continued superior and safe performance, provided:
1. They are installed, commissioned, operated and
maintained in accordance with the recommendations given
in this Manual.
2. Periodic attention is given, as necessary, to maintain the
product in good functional order. Recommended
guidelines are given in the section.
Carefully inspect the new fixture for any signs of damage.
When installing Kohler Products, manufacturers guidelines for
power tool safety should be followed.
MAINTENANCE
1.
2.
CHANGSHU KOHLER LTD., SOUTHEAST ECONOMIC DEVELOPMENT ZONE,
CHANGSHU, JIANGSU PROVINCE, CHINA POST CODE 215500
215500
©
©
Copyright Kohler China Investment Co., Ltd. 2016
2016
1260681-T01-C

Fig.2
2
ROUGHING-IN
INSTALLATION
-2-
UNIT : mm
K-96103T
600mmMaxiSpace Cabinet
600mm
K-96104T
900mmMaxiSpace Cabinet
900mm
A. Install Washbasin Cabinet
Install the services.
Hot (H) and Cold (C) inlets must be connected to the correct
inlet pipes.
Install the drain in accordance with the manufacturer's
instructions.
We suggest using P-trap drain. Connect P-trap pipe with
washbasin drain.
Make sure a watertight seal exisits on all
washbasin drain connections.
Provide access to the plumbing connections
for future plumbing maintenance.
The hot and cold water supplies must be installed with
isolating valves.
Caution!
Caution!
A.
(H) (C)
P
Fig.1
1
UNIT : mm
Kohler reserves the right to change marked dimensions without prior notice.
Reference
445 445
663
663
590
890
+2
-2
+2
-2
1260681-T01-C

-3-
Fig.3
3
UNIT : mm
1.
1. Mark the position of hanged bracket and wall bolt
according to dimensions as illustrated, and loosen the
suspension hook of washbasin cabinet.
Avoid the cables and pipes inner set when
drilling in the wall.
Different types of bolts are required for different
decoration boards. Please apply suitable bolts and plugs.
Caution!
Note:
2.
3.
65-75mm
2. Drill holes for fixing the bracket and bolt. Using a level to
ensure that the hanged bracket is level.
3. Use suitable plugs and bolts, and fix the bracket and bolt
on the wall. Fix the bolts supplied with the vanity on the
wall. Each bolt shall be 65-75mm out of the wall.
4.
4. Apply silicone sealant onto the contact surface of the
cabinet and vanity. Wait for the sealant to cure.(Install
adjustable feet first if needed.)
Fig.4
4
Apply Silicone Sealant
Apply Silicone Sealant
Apply Silicone Sealant Apply Silicone Sealant
Center Center
Vanity Wall Bolt Holes Vanity Wall Bolt Holes
Cabinet Wall Bolt Holes
Cabinet Wall Bolt Holes
Cabinet Outline Cabinet Outline
Wall Bracket Wall Bracket
590
22
180
220 220
650
650
27 27
593
593
120
120
684
684
833
833
890
292.5292.5
370
370
1260681-T01-C

-4-
5.
6.
a.
b. 2
5. Fix faucet and drain according to their installation
instructions.
6. Fix onto wall.
a. Lift the cabinet and vanity by two people. Align the vanity
hanging hole with the bolts on the wall. Make the bolts
through the vanity hanging hole.
b. Hang the two back wall clips onto the pre-fixed bracket on
the wall.
Fig.5
5
Vanity Wall Bolt Holes
Wall Bracket
First
Second
c.
d.
c. Adjust the cabinet and vanity level. Put the cabinet against
the wall by adjusting the screws of wall clips.
d. Fix the cabinet and vanity again with the bolts according to
pre-drilled cabinet fixing holes on the wall.
MAX1
24
3
1
8
Fig.6
6
Fig.7
7
1260681-T01-C

7. Connect water pipe and drain by professionals to ensure
there is no leakage.
Note: Different types of bolts are required for different
decoration boards. Please apply suitable bolts and plugs.
7.
e.
e. Open the cabinet door and the drawer. Fix the bolt
according the vanity installation instructions. Before that ,
please apply silicone sealant onto the contact surface of
the vanity and the wall.
Washer Nut
Offset Nut
Fig.8
8
Fig.9
9
a. (P )
/U
Connect Drainage
a. Inwall drainage (P-Trap)
Please install the drain assembly and faucet as shown.
Please set the water supply and drainage position
according to the suppliers instructions. You can put the
pipe into the U Notch.
Faucet
Supply Lines
Shut-off Valve
Drain Assembly
-5-
1260681-T01-C

Fig.11
11
-6-
8.
a.
b.
8. Ajust the cabinet.
a. Place the hinge cover and plastic cover(in the hardware
pack).
b. Adjust the hinge of door in 3 direction to make sure the
door level.
b. S
U
b. Floor drainage (S-Trap)
Please install the drain assembly and faucet as shown.
Please set the water supply and drainage position
according to the suppliers instructions. You can put the
pipe into the U Notch.
Faucet
Supply Lines
Shut-off Valve
Drain Assembly
Ripple Pipe
Outlet
Fig.10
10
1260681-T01-C

-7-
1.
2.
3.
4.
5.
6.
7.
USER MAINTENANCEUSER MAINTENANCE
Warning! Risk of product damage.
1.
2.
3.
4.
5.
6. Please do not sit, lean or step on the basin cabinet.
7. If any fixtures caused by abnormal reasons, Kohler China
can supply paid replacement for service parts caused by
abnormal reasons as shown in the Service Parts Page in
the limited duration of warranty.
Many cleansers contain abrasive and chemical substance
which is not suitable for cleaning stainless steel, enamel,
plating or plastic products. You may use mild cleansers or
soaps to clean the surfaces. Wipe any splashes of cleaner
solutions from the surface with clean soft cloth.
Maintain ventilation in the bathroom, and separate the dry
area from the damp one if conditions permit. Try to open
the door and windows of the bathroom and maintain good
ventilation.
Kohler bathroom cabinet are dealt with strict procedures
for damp-proof, whose good damp-proof function ensures
good performance even in bathroom of huge humidity. Yet
do not splash and pour water directly on the bathroom
cabinet. Make sure that the bathroom is not over damp
and wipe any splashes from surfaces immediately.
Maintenance of door board: Clean and wipe door board
regularly, and wipe the condensation vapor with dry and
soft cloth.
Ensure that electrical connections for appliances such as
head lamp is insulated wipe mirror surface with chamois
regularly to guarantee the persistent excellent performance.
1260681-T01-C