Kohler SIMPLICE 596T-4E User manual

1434194-AN2-A 1
1434194-AN2-A 4
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTE:
1. Flush the water supply pipes thoroughly to remove debris.
2. An inline water filter must be used with this product.
3. For new installations, install the faucet to sink before installing.
4. The highest working pressure for sprayhead is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure reducer is
needed. The highest water and environment temperature is 60ºC. Please keep sprayhead from heater, or it may
become damaged and cause injury to the user.
5. All installations should comply with the relevant requirements of AS/NZS 3500 and AS/NZS 6400.
596T-4E Pull-down Kitchen Faucet596T-4E Pull-down Kitchen Faucet
ROUGH-IN DIMENSIONS
INSTALLATION INSTRUCTIONS
SIMPLICESIMPLICE
SERVICE PARTS
Ø34~Ø41
Ø51
64 Max.
81 234
745
141
229682
406
14º
G1/2˝
**Color code must be specified when ordering.
1374687
1046153
1296289
1218824**
1447895
1307337
1288332
1446854
1267359
58946
1128531
1106466
1086396
1384194
1297533
1303572
1384195
1232505
1319955
1288038
1288208**
1243689**
1228706
56823

CARE AND MAINTENANCE
OPERATION INSTRUCTION
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
INSTALLATION
1434194-AN2-A 3
1434194-AN2-A 2
How to Install the Faucet
Slide the escutcheon(1) over the hoses and
shank(2) until it contacts the faucet(3) bottom.
From upside of the sink, insert the faucet assembly
into the mounting hole until the escutcheon bottom is
against the deck. Ensure the handle is on the right.
Partially thread two screws(4) into the threaded
ring(5). From underside of the sink, place the
washer(6) and threaded ring with two screws over
the shank(2). Position the faucet so that the spray
hose(7) is on the left, the spray hose and two supply
hoses(8) are symmetrical. Thread the threaded ring
onto the shank until the washer contacts the
underside of the sink. Tighten two screws(4) to
secure the faucet to sink.
Attach the hoses(8) to water supplies. The hose with
blue dot should be connected to cold water. The
hose with red dot should be connected to hot water.
Slide the weight(9) over the spray hose(7).
Tighten the connector(10) onto the spray hose,
and then install it to the outlet hose(11). Adjust the
weight to the appropriate position, check for smooth
operation, and secure it with a loose cable tie(12).
Turn on the faucet, rub the sprayhead nozzles to
dislodge debris.
To improve water flow, trun off the faucet. Discon-
nect the sprayhead. Remove and clean the
screen(14) inside the sprayhead.
Reinsert the screen and reconnect the sprayhead.
INSTALLATION CHECKOUT
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off position.
Turn on the main water supply and drain, and check
for leaks. Repair as needed.
Remove the sprayhead(13). Run hot and cold water
about one minute to remove any debris. Shut off the
faucet. Reinstall the sprayhead.
13
1
4
7
9
12
12
9
8
3
5
2
6
11
10
7
14
Turn on the handle gently. Turn clockwise for cold
water, counter-clockwise for hot water.
If you want to use the sprayhead by hand, take the
sprayhead and pull out the hose.
Press different position A or B of the button(15),
you will get different water flow as shown. Press
and hold the button(16), it will stop water flow.
NOTE: Please pull it gently and do not draw out the
spray hose too long, or you may damage the hose
and connector.
A
B
16
15