Konica Minolta Color Care IQ-501 User manual

IQ-501 Quick Guide
KONICA MINOLTA

2/27/2020 5:45 PM／D11
1
Table of contents
Want to Do/Step Execution
Timing Procedure Page
1a. Dairy Care/Preparation Initial only
(one time)
- Basic settings (step 1-35)
- Setting Summary
p.2
p.12
1b. Dairy Care/Execution Everyday - Auto Run (step 1-6)
p.13
Once a day - Manual Execution (step 7-12) p.15
2. Adjust registration for
new paper/Execution
When Combination
of Paper and tray
is changed
- Loading paper to
/Main Body (step 1-9)
/PF-602m(normal) (step 10-19)
/PF-602m(small) (step 20-25)
/PF-707m(normal) (step 26-34)
/PF-707m(small) (step 35-40)
/LU-202m/202XL/XLm (step 41-49)
p.17
-Auto Measure (step 50-62) p.34
3a. Keep registration and
constant color reproduction
during long printing for the
job with Trim Margin
/Preparation
When paper is
changed
- Confirm paper size (Step 1)
- Conformation of Auto Image Adj.
Settings (Step 2-11)
- Package color auto adj. incl
Color Density Control (Step 12-17)
- Both side adjustment (Step 18-30)
- Setting Summary
p.38
p.46
3b.Keep registration and
constant color reproduction
during long printing for the
job with Trim Margin
/Execution
When you start
printing long job
actually
- Print the job by
/Konica Minolta controller (A)
/EFIcontroller (B)
/CREO controller (C) p.47
4a.Keep registration and
constant color reproduction
during long printing for the
job without Trim Margin
/Preparation
When paper is
changed
- Color Density Control setting
(Step 1-7)
- Periodical Both Side Adjustment
setting (Step 8-9)
- Setting Summary
p.49
p.51
4b.Keep registration and
constant color reproduction
during long printing for the
job with Trim Margin
/Execution
When you start
printing long job
actually
- Print the job by
/Konica Minolta controller (A)
/EFIcontroller (B)
/CREO controller (C)
p.52
NOTICE This manual describes the procedures for C3080 as an example.

2/27/2020 5:45 PM／D11
2
1
Load “Max density adjustment” paper
into the tray 1.
(Tray # is an example in this manual)
✔ As for selecting adjustment paper, please consult
with service representative.
In general, coated paper is recommended since
color and density reproduction are stable.
Load “the paper actually used for the job”
into the tray 2.
(Tray # is an example in this manual)
✔ An paper should be
lengthwise (X): 420.0 mm to 487.7 mm,
widthwise (Y): 279.4 mm or more).
1a. Daily Care /Preparation (=Basic settings)

2/27/2020 5:45 PM／D11
3
2
Press the “Utility/Counter” key.
3
Press [Administrator Setting].
4
If the [Administrator Password] screen
is displayed, enter the administrator
password using 8 to 64 one-byte
characters, then press [OK].
✔ The administrator password must be specified using
8 to 64 one-byte
characters.
5
The [Administrator Setting Menu] screen
is displayed.
Press [System Setting].
6
Press [Expert Adjustment].

2/27/2020 5:45 PM／D11
4
7
Press [Quality Adjustment].
8
Press [Custom Screen].
9
Select [Dot190] for [Screen1]
Press [OK].
10
Press [Exit].

2/27/2020 5:45 PM／D11
5
11
Press [Adjustment] on the [MACHINE]
screen.
12
Press [Quality Adjustment].
13
Press [Color Density Control].
14
Press [Basic Setting].

2/27/2020 5:45 PM／D11
6
15
Select each item as follows
- [Use Color Density Control] > [ON]
- [Periodical Adj. Execution] > [ON]
- [Adjustment Execution timing]
> [During Job Runs]
- [Chart Tray Setting] > [OFF]
Press [Next].
16
Select each item as follows
- [Adjustment Interval] > [ON]
Press [Change] and set [1000 pages].
- [Concurrent Execution of BothSidesAdj.]
> [ON]
Press [OK].
17
Press [Close].

2/27/2020 5:45 PM／D11
7
18
Press [Image Diagnosis]
NOTICE
If [Image Diagnosis] is not displayed even
IQ-501 is equipped, please contact your service
representative.
19
Press [Basic Setting].
20
Select each item as follows
[DetailedDiagnosis/Sync.SimpleDiagnosis]
> [ON]
[Detailed Diagnosis Result Auto Reset]
> [ON]
[Output Stored Job after Diagnosis]
> [OFF]
Press [OK].
21
Press [Close].

2/27/2020 5:45 PM／D11
8
22
Press [Package Color Auto Adj.].
23
Press [Initial Set.].
<KM controller>
<EFI/CREO controller>
24
Select each item as follows
For KM controller
- [Screen of Adjustment Target] > [Screen1]
- [Auto Selection] > [OFF]
- [Gamma Auto. Adj.] > [ON]
- [Dens. BalanceAdj.] > [ON]
- [Max Density Adj.] > [ON]
- [Color Density] > [ON]
- [Exact Color] or [G7 Calibration] > [ON]
- [Exact Color : Number of Output Job] > [1] or
- [G7 Calibration : Number of Output Job] > [1]
For EFI/CREO controller
- [Screen of Adjustment Target] > [Screen1]
- [Auto Selection] > [OFF]
- [Gamma Auto. Adj.] > [ON]
- [Dens. BalanceAdj.] > [ON]
- [Max Density Adj.] > [ON]
- [Color Density] > [ON]
- [ControllerCalib.] > [ON]
Press [Next].

2/27/2020 5:45 PM／D11
9
25
[Maximum Density
Adjustment Tray] > [Tray1]
Press [Next].
(“Max density adjustment paper is loaded
into the tray 1 as an example.)
26
Select each item as follows
- [Adjustment Tray] > [Tray2]
- [Auto Run] > [OFF]
- [Overwrite Tray Set. of Max.DensityAdj.]
> [ON]
Press [OK].
(“The paper actually used for the job is
loaded into the tray 1 as an example.)
27
Press [Start].