Konica Minolta TWIN Driver User manual

User’s Guide

TWAIN Driver x-1
Introduction
Thank you for purchasing this machine.
This manual provides the information required to use this machine for scan-
ning.
Be sure to read this manual before performing any operations.
For precautions concerning the use and safety of the machine, refer to the
User’s Guide provided with the machine.
Store the CD-ROM and User’s Guides provided with the machine in a safe
place.
Trademarks and copyright
-KONICA MINOLTA, the KONICA MINOLTA logo, and The essentials of
imaging are registered trademarks of KONICA MINOLTA HOLDINGS,
INC.
-PageScope and bizhub are registered trademarks or trademarks of
KONICA MINOLTA BUSINESS TECHNOLOGIES INC.
-Netscape is a registered trademark of Netscape Communications Corpo-
ration in the United States and other countries.
-Novell and Novell NetWare are registered trademarks of Novell, Inc. in the
United States and other countries.
-Microsoft, Windows, and Windows NT are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other
countries.
-Adobe, the Adobe logo, Acrobat and PostScript are either registered
trademarks or trademarks of Adobe Systems Incorporated in the United
States and/or other countries.
-Ethernet is a registered trademark of Xerox Corporation.
-PCL is a registered trademark of Hewlett-Packard Company Limited.
-All other product and brand names are trademarks or registered trade-
marks of their respective companies or organizations.

TWAIN Driver x-2
Copyright
© 2007 Konica Minolta Business Technologies, Inc. All Rights Reserved.
Note
-This User’s Guide may not be reproduced in part or in full without permis-
sion.
-Konica Minolta Business Technologies, Inc. will not be held liable for any
incidents caused by using this User’s Guide.
-Information included in this User’s Guide is subject to change without no-
tice.
-Views of the actual equipment may be slightly different from the illustra-
tions used in this User’s Guide.

TWAIN Driver x-3
Software End User License Agreement
PLEASE READ CAREFULLY THE LICENSE AGREEMENT BELOW BEFORE
OPENING THE PACKAGE OF THIS SOFTWARE (“SOFTWARE”), DOWN-
LOADING, INSTALLING OR USING THE SOFTWARE. OPENING THE PACK-
AGE, OR DOWNLOADING, INSTALLING OR USING THE SOFTWARE
SHALL BE DEEMED YOUR LAWFUL ACCEPTANCE OF THE TERMS AND
CONDITIONS BELOW. IF YOU DO NOT AGREE TO THEM, DO NOT DOWN-
LOAD, INSTALL, USE THE SOFTWARE, NOR OPEN THE PACKAGE.
1. COPYRIGHT AND INTELLECTUAL PROPERTY RIGHTS
This is a license agreement and not an agreement for sale. Konica Minolta
Business Technologies, Inc. (“Konica Minolta”) owns, or has been licensed
from other owners (“Konica Minolta Licensor”), copyrights and other intellec-
tual property rights of the Software, and any and all rights and title to the
Software and any copy made from it are retained by Konica Minolta or Koni-
ca Minolta Licensor. In no event, this Agreement shall be deemed to assign
any copyright and/or any intellectual property rights of the Software from
Konica Minolta or Konica Minolta Licensor to you. The Software is protected
by copyright laws and international treaty provisions.
2. LICENSE
Konica Minolta hereby grant to you a non-exclusive and limited license, and
you may:
(i) install and use the Software only on your computer(s) connected with
Konica Minolta product for which this Software is designed;
(ii) allow users of the computers described above to use the Software, pro-
vided that you assure that all such users comply with the terms of this Agree-
ment;
(iii) use the Software only for your own customary business or personal pur-
pose;
(iv) make one copy of the Software only for backup purpose in the support
of the normal and intended use of the Software.
(v) transfer the Software to other party by transferring a copy of this Agree-
ment and all documentation along with the Software, provided that (a) you
must, at the same time, either transfer to such other party or destroy all your
other copies of the Software, (b) such transfer of possession terminates your
license from Konica Minolta, and (c) you must assure that such other party
has agreed to accept the terms and conditions of this Agreement. If such
other party does not accept such terms and conditions then you shall not
transfer any copy of the Software.
3. RESTRICTIONS
(1) You shall not without the written consent of Konica Minolta:

TWAIN Driver x-4
(i) use, copy, modify, merge or transfer copies of the Software except as pro-
vided herein;
(ii) reverse engineer, reverse assemble, reverse compile or any other way an-
alyze the Software; or
(iii) sublicense, rent, lease or distribute the Software or any copy thereof.
(iv) remove, use, or alter any trademark, logo, copyright or other proprietary
notices, legends, symbols or labels in the Software.
(2) You agree that you will not export the Software in any form in violation of
any applicable laws and regulations regarding export control of any country.
4. DISCLAIMER OF WARRANTIES
(1) If the Software is furnished on CD-ROM(s) or other tangible object that is
used for storage of digital data (hereinafter collectively “Storage Medium”),
Konica Minolta warrants the Storage Medium to be free from the defects in
material and workmanship under normal use, for a period of ninety (90) days
from the date of delivery to you. WITH THE EXCEPTION OF THE FOREGO-
ING EXPRESS WARRANTIES APPLICABLE TO STORAGE MEDIUM ONLY,
THE SOFTWARE IS PROVIDED TO YOU “AS IS” WITHOUT ANY WARRAN-
TIES WHATSOEVER. KONICA MINOLTA, ITS AFFILIATE COMPANIES AND
KONICA MINOLTA LICENSOR DISCLAIM ALL WARRANTIES WITH RE-
GARD TO THE SOFTWARE, EXPRESS OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD
PARTY RIGHTS.
(2) IN NO EVENT WILL KONICA MINOLTA, ITS AFFILIATE COMPANIES NOR
KONICA MINOLTA LICENSOR BE LIABLE FOR ANY LOST PROFITS, LOST
DATA, OR ANY OTHER INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR
CONSEQUENTIAL DAMAGES THAT RESULT FROM USE OR INABILITY TO
USE THE SOFTWARE INCLUDING WITHOUT LIMITATION, DAMAGES FOR
LOSS OF GOODWILL, COMPUTER FAILURE OR MALFUNCTION OR ANY
AND ALL OTHER COMMERCIAL OR OTHER DAMAGES OR LOSSES, EVEN
IF KONICA MINOLTA, ITS AFFILIATE COMPANIES OR KONICA MINOLTA
LICENSOR HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAG-
ES OR FOR ANY CLAIM BY YOU BASED ON A THIRD PARTY CLAIM.
(3) The disclaimer of warranty hereunder does not affect your statutory rights.
In case of the disclaimer is not allowed by applicable law, the disclaimer shall
only apply to you to the maximum extent permitted by the law.
5. TERMINATION
You may terminate this license at any time by destroying the Software and
all your copies of it. This Agreement shall also terminate if you fail to comply
with any terms hereof. Upon such termination, you must immediately destroy
all copies of the Software in your possession.

TWAIN Driver x-5
6. GOVERNING LAW
This Agreement shall be governed by the laws of Japan.
7. SEVERABILITY
In the event that any part or parts of this agreement shall be held illegal or
null and void by any court or administrative body of competent jurisdiction,
such determination shall not effect the remaining parts of this agreement and
they shall remain in full force and effect as if such part or parts determined
illegal or void had not been included.
8. NOTICE TO US GOVERNMENT END USERS
The Software is a “commercial item,” as that term is defined at 48 C.F.R.
2.101 (October 1995), consisting of “commercial computer software” and
“commercial computer software documentation,” as such terms are used in
48 C.F.R. 12.212 (September 1995). Consistent with 48 C.F.R. 12.212 and
48 C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all U.S. Government
End Users shall acquire the Software with only those rights set forth herein.
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UN-
DERSTAND IT, AND AGREE TO BE BOUND BY ITS TERMS AND CONDI-
TIONS. NEITHER PARTY SHALL BE BOUND BY ANY OTHER STATEMENTS
OR REPRESENTATIONS THAT ARE INCONSISTENT WITH THE TERMS
AND CONDITIONS OF THIS AGREEMENT. NO AMENDMENT TO THIS
AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED BY PROPER-
LY AUTHORIZED REPRESENTATIVES OF EACH PARTY. BY OPENING THE
PACKAGE, DOWNLOADING, INSTALLING OR USING THE SOFTWARE
YOU AGREE TO ACCEPT THE TERMS OF THIS AGREEMENT.

TWAIN Driver x-6
Contents
Introduction
Copyright ........................................................................................ x-2
Software End User License Agreement ..........................................x-3
Contents ............................................................................................. x-6
Explanation of manual conventions ................................................ x-8
1 Setting up for scanning
2 Installing the TWAIN driver
2.1 Making connections and installing the driver ................................2-1
Connecting to a computer ..............................................................2-1
Procedures for making connections and installing the driver ........ 2-2
2.2 General operation for driver installation .........................................2-4
Installation using Plug and Play ...................................................... 2-4
Installation using the TWAIN Driver Installer .................................. 2-4
2.3 Installing the TWAIN driver by using Plug and Play .......................2-5
Connecting to the computer’s USB port ........................................ 2-5
Installing using Plug and Play on Windows XP/Server 2003 .......... 2-6
Installing using Plug and Play on Windows Vista ........................... 2-7
Installing using Plug and Play on Windows 2000 ........................... 2-9
Installing using Plug and Play on Windows Me ............................ 2-10
2.4 Installing the TWAIN driver by using the installer ........................2-12
Connecting to a computer through a network ............................. 2-12
2.5 Reinstalling the TWAIN driver by using the installer ....................2-15
2.6 Uninstalling the TWAIN driver ........................................................2-17
Deleting the TWAIN driver by using Control Panel .......................2-17
Deleting the TWAIN driver by using the installer .......................... 2-18
3 Scanning a document
3.1 Using the automatic document feeder ...........................................3-1
3.2 Using the original glass ....................................................................3-3

TWAIN Driver x-7
4 Driver settings
4.1 TWAIN scanner driver .......................................................................4-1
Document Size ............................................................................... 4-2
Scan Mode ..................................................................................... 4-3
Resolution ....................................................................................... 4-3
Scan Type ....................................................................................... 4-4
Duplex Scanning ............................................................................ 4-4
Brightness ....................................................................................... 4-5
I/O Type .......................................................................................... 4-5
Help ................................................................................................ 4-6
About .............................................................................................. 4-6
Scan ................................................................................................ 4-6
Cancel ............................................................................................. 4-6
5 Error messages
5.1 Paper misfeeds ..................................................................................5-1
Clearing a misfeed in the automatic document feeder .................. 5-2
Transmission error .......................................................................... 5-5
Scanning ......................................................................................... 5-5
Scanning error ................................................................................ 5-6
Automatic document feed no paper ...............................................5-6
Other machine errors ...................................................................... 5-7

TWAIN Driver x-8
Explanation of manual conventions

Setting up for scanning 1
TWAIN Driver 1-1
1 Setting up for scanning
If the enclosed TWAIN driver is installed on the computer, this machine can
be used to scan a document and send it to the computer.
For scanning, an environment that includes the following software and hard-
ware is required.
2
Reminder
The TWAIN driver is not compatible with Windows 95/98/ NT 4.0.
Item
Compatible operating
systems
Windows Vista/Windows XP/Windows Server 2003/Windows
2000/Windows Me/Windows 98 SE
Windows Vista x64 Edition/Windows Server 2003 x64 Edition/
Windows XP Professional x64 Edition
Computer applications TWAIN-compatible image-processing software (such as, Ado-
be Photoshop or Acrobat Professional)
Connection port Compliant with USB V. 2.0 (Windows 98 SE is not supported.)
10Base-T/100Base-TX (when the optional network interface
card NC-503 or image controller IC-206 is installed)

Setting up for scanning 1
TWAIN Driver 1-2

Installing the TWAIN driver 2
TWAIN Driver 2-1
2 Installing the TWAIN driver
This chapter provides descriptions on connecting the machine to a computer
and installing the TWAIN driver.
2.1 Making connections and installing the driver
Connecting to a computer
This machine can be connected to a computer using any of the following
connection methods.
Connecting to a USB port
In the following procedure, the machine is connected directly to the compu-
ter by using a USB cable.
When the machine is connected to the USB port, installation of the TWAIN
driver begins. For the procedure on connecting this machine with USB, refer
to “Installing the TWAIN driver by using Plug and Play” on page 2-5.
2
Reminder
This machine cannot be connected to a computer running Windows 98
SE using a USB interface.

Installing the TWAIN driver 2
TWAIN Driver 2-2
Connecting to the network
In order to perform TWAIN scanning on a network, the optional network in-
terface card NC-503 or image controller IC-206 must be installed. For details
on connecting this machine to the network, refer to “Installing the TWAIN
driver by using the installer” on page 2-12. For details on the network inter-
face card NC-503 and image controller IC-206, refer to the corresponding
User’s Guide.
Procedures for making connections and installing the driver
The TWAIN driver can be installed by using Plug and Play or by using the in-
staller.
The installation procedure differs depending on the method used to make
the connection. Use the installation method that corresponds with the con-
nection method.
2
Reminder
If the machine is to be connected to a USB port, install the driver by using
Plug and Play. If the machine is to be connected to a network, install the
driver by using the installer.
Connection
method
Supported operating sys-
tems
TWAIN driver installation method
USB port con-
nection
Windows XP, Windows
Server 2003, Windows Vista,
Windows 2000 and Win-
dows Me
Install using Plug and Play.
For details, refer to “Installing the TWAIN
driver by using Plug and Play” on
page 2-5.

Installing the TWAIN driver 2
TWAIN Driver 2-3
2
Note
When installing using Plug and Play, the printer driver is also installed af-
ter the TWAIN driver. For details on the printer driver, refer to the User’s
Guide for the GDI printer driver or the image controller IC-206.
This machine cannot be connected to a computer running Windows 98
SE using a USB interface.
Network connec-
tion
Windows XP, Windows
Server 2003, Windows Vista,
Windows 2000, Windows
Me and Windows 98 SE
Install using the installer.
For details, refer to “Installing the TWAIN
driver by using the installer” on
page 2-12.
Connection
method
Supported operating sys-
tems
TWAIN driver installation method

Installing the TWAIN driver 2
TWAIN Driver 2-4
2.2 General operation for driver installation
The driver is installed according to the following general operation.
Installation using Plug and Play
When installing the driver by using Plug and Play, the installation procedure
differs depending on the operating system.
Installation using the TWAIN Driver Installer
When installing the driver by using the TWAIN Driver Installer, the installation
procedure is the same for all operating systems.
With Windows Me
With Windows XP,
Windows Server 2003,
Windows Vista,
and Windows 2000
Install the TWAIN driver.
Install the USB printing support driver.
Install the printer driver.
With Windows 98 SE With Windows Me
With Windows XP,
Windows Server 2003,
Windows Vista,
and Windows 2000
Install the TWAIN driver.

Installing the TWAIN driver 2
TWAIN Driver 2-5
2.3 Installing the TWAIN driver by using Plug and Play
Connecting to the computer’s USB port
When this machine is connected to a computer with a USB cable, Plug and
Play detects the device, and then installation of the necessary drivers begins.
1Start Windows, and then insert the CD-ROM into the computer’s CD-
ROM/DVD drive.
2Turn on this machine.
3After this machine starts up and is ready for copying, connect it to the
computer with the USB cable.
This machine is detected, and the Found New Hardware Wizard (Add New
Hardware Wizard on Windows Me) appears.
The remainder of the procedure differs depending on the operating system.
Follow the instructions in the dialog boxes that appear for the operating sys-
tem being used.
-For Windows XP and Windows Server 2003: “Installing using Plug and
Play on Windows XP/Server 2003” on page 2-6
-For Windows Vista: “Installing using Plug and Play on Windows Vista” on
page 2-7
-For Windows 2000: “Installing using Plug and Play on Windows 2000” on
page 2-9
-For Windows Me: “Installing using Plug and Play on Windows Me” on
page 2-10

Installing the TWAIN driver 2
TWAIN Driver 2-6
2
Note
With Windows XP, Server 2003, Vista and 2000, log on as a user with Ad-
ministrator privileges to install the driver.
Installing using Plug and Play on Windows XP/Server 2003
2
Note
If the driver is installed using Plug and Play, first the TWAIN driver is in-
stalled, and then installation of the printer driver begins. The procedure
described in this manual is for the installation of the TWAIN driver, then
the printer driver. For details on the printer driver, refer to the User’s
Guide for the GDI printer driver or the image controller IC-206.
2
Note
When using Windows XP (Service Pack 2), the following dialog box may
appear, requesting confirmation to connect to Windows Update. At this
time, select “No, not this time”, and then click the [Next] button.
Follow the instructions that appear in the Found New Hardware Wizard to
complete the installation.
1Select “Install from a list or specific location (Advanced)”, and then
click the [Next] button.
2Select “Include this location in the search” as the location to be
searched for the driver, and then specify the following folder on the CD-
ROM as the location where the driver is saved.
– Folder to be specified:
\Driver\WIN2K_XP\English
– With 64-bit operating systems, select “\Driver\WinVista64\English”.
– The folder can be selected after clicking the [Browse] button.
3Click the [Next] button.
– When the Windows logo testing warning message appears, click
the [Continue Anyway] button.

Installing the TWAIN driver 2
TWAIN Driver 2-7
4When the Completed Found New Hardware Wizard dialog box ap-
pears, click the [Finish] button.
This completes the installation of the TWAIN driver.
The Found New Hardware Wizard appears again, and the installation
of the printer driver begins.
5Repeat steps 1 through 4 to install the printer driver.
Installing using Plug and Play on Windows Vista
2
Note
If the driver is installed using Plug and Play, first the TWAIN driver is in-
stalled, and then installation of the printer driver begins. The procedure
described in this manual is for the installation of the TWAIN driver, then
the printer driver. For details on the printer driver, refer to the User’s
Guide for the GDI printer driver or for image controller IC-206.
Follow the instructions of the Found New Hardware wizard, and then click
complete the installation.
1In the Found New Hardware wizard, select “Locate and install driver
software (recommended)”.
– If the User Account Control dialog box appears, click the [Continue]
button.
– If a message appears, requesting confirmation to search online,
click the [Don’t search online] button.

Installing the TWAIN driver 2
TWAIN Driver 2-8
2In the dialog box for checking the disk, click the [I don’t have the disk.
Show me other options.] button.
3Insert the printer driver CD into the CD-ROM/DVD drive of the compu-
ter.
4Click the [Browse my computer for driver software (advanced)] button.
5Select “Include subfolders”, and then specify the following folder on
the CD-ROM as the location where the driver is saved.
– Folder to be specified: \Driver\WinVista\English
– With 64-bit operating systems, select “\Driver\WinVista64\English”.
– The folder can be selected after clicking the [Browse] button.
6Click the [Next] button.
– In the Windows Security dialog box, select “Install this driver soft-
ware anyway”.
7After the installation is finished, click the [Close] button.
This completes the installation of the TWAIN driver.
The Found New Hardware wizard appears again, and the installation of
the printer driver begins.
8Repeat steps 2 through 7 to install the printer driver.

Installing the TWAIN driver 2
TWAIN Driver 2-9
Installing using Plug and Play on Windows 2000
2
Note
If the driver is installed using Plug and Play, first the TWAIN driver is in-
stalled, and then installation of the printer driver begins. The procedure
described in this manual is for the installation of the TWAIN driver, then
the printer driver. For details on the printer driver, refer to the User’s
Guide for the GDI printer driver or the image controller IC-206.
Follow the instructions that appear in the Found New Hardware Wizard to
complete the installation.
1Check the contents of the Found New Hardware Wizard, and then click
the [Next] button.
2Select “Search for a suitable driver for my device [recommended]”, and
then click the [Next] button.
3Select “Specify a location”, and then click the [Next] button.
4Specify the following folder on the CD-ROM as the location where the
driver is saved.
– Folder to be specified:
\Driver\WIN2K_XP\English
– The folder can be selected after clicking the [Browse] button.
5Click the [Next] button.
– When the Microsoft digital signature warning message appears,
click the [Continue Anyway] button.
6When the Completed Found New Hardware Wizard dialog box ap-
pears, click the [Finish] button.
This completes the installation of the TWAIN driver.
The Found New Hardware Wizard dialog box appears again, and the
installation of the printer driver begins.
7Repeat steps 1 through 6 to install the printer driver.