Kramer PT-2C User manual

P/N: 2900-300494 Rev 3 www.kramerAV.com
USER MANUAL
MODEL:
PT‑2C
Extended EDID Processor

Kramer Electronics Ltd.
PT‑2C –Contents
i
Contents
Introduction 1
Getting Started 1
Overview 2
Overview 3
Defining the PT‑2C Extended EDID Processor 4
Connecting the PT‑2C 5
Configuring the PT‑2C 6
EDID loading/storing 7
Default EDID 8
Technical Specifications 11
Supported Resolutions 12

Kramer Electronics Ltd.
PT‑2C –Introduction
1
Introduction
Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been providing a world
of unique, creative, and affordable solutions to the vast range of problems that confront the
video, audio, presentation, and broadcasting professional on a daily basis. In recent years, we
have redesigned and upgraded most of our line, making the best even better!
Getting Started
We recommend that you:
•Unpack the equipment carefully and save the original box and packaging materials for
possible future shipment.
•Review the contents of this user manual.
Go to www.kramerav.com/downloads/VP-734 to check for up-to-date user manuals,
application programs, and to check if firmware upgrades are available (where appropriate).
Achieving the Best Performance
•Use only good quality connection cables (we recommend Kramer high-performance,
high-resolution cables) to avoid interference, deterioration in signal quality due to poor
matching, and elevated noise levels (often associated with low quality cables).
•Do not secure the cables in tight bundles or roll the slack into tight coils.
•Avoid interference from neighboring electrical appliances that may adversely influence
signal quality.
•Position your Kramer PT‑2C away from moisture, excessive sunlight and dust.
This equipment is to be used only inside a building. It may only be connected to other
equipment that is installed inside a building.
Safety Instructions
Caution: There are no operator serviceable parts inside the unit
Warning: Use only the Kramer Electronics power supply that is provided with the unit
Warning: Disconnect the power and unplug the unit from the wall before installing
Recycling Kramer Products
The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC aims to reduce
the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected
and recycled. To comply with the WEEE Directive, Kramer Electronics has made
arrangements with the European Advanced Recycling Network (EARN) and will cover any
costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on

Kramer Electronics Ltd.
PT‑2C –Introduction
2
arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular
country go to our recycling pages at www.kramerav.com/support/recycling.
Overview
Congratulations on purchasing your Kramer PT‑2C Extended EDID Processor. This
product, which incorporates HDMI™ technology, is ideal for:
•Legacy infrastructures that require advanced feature support
•Troubleshooting aid for installers on legacy infrastructures
•Education, entertainment corporate and government

Kramer Electronics Ltd.
PT‑2C –Overview
3
Overview
The PT‑2C is an EDID processor for HDMI signals. It allows you to pass or block HDCP,
deep audio or deep color signals that may or may not be compatible with the display.
The PT‑2C features:
•A maximum data rate of 10.2Gbps (3.4Gbps per data channel)
•4K resolution support
•Compliance with HDMI and HDCP standards
•CEC and ARC support
•HDMI input and output connectors
•Signal reclocking
•Active video signal source detection
•LED indication for input, output and power as well as successful EDID capture
•Configurable timeout for when the input signal is lost
•Restore DDC clock rate on display side
•Program DIP-switches that control the desired functions
•Mini USB for EDID Designer and FW update support
•+5V DC Power supply
•The ultra-compact PicoTools case that allows four units to be mounted side-by-side in a
1U rack space with the optional RK-4PT 19” rack adapter

Kramer Electronics Ltd.
PT‑2C –Defining the PT‑2C Extended EDID Processor
4
Defining the PT‑2C Extended
EDID Processor
Figure 1 defines the front and rear panels of the PT‑2C.
Figure 1: PT‑2C Front and Rear Panels
#
Feature
Function
1
EDID DESIGNER/F/W UPDATE
Mini USB Connector
Connect to a PC/laptop running EDID Designer to modify the
EDID, or to update the firmware of the
PT‑2C
2
IN LED
Lights green when an HDMI active signal source is connected
to the input
3
OUT LED
Lights green when an HDMI acceptor is connected to the
output
Blinks three times upon successful load of the designed EDID
and then resumes to normal operation.
4
ON LED
Lights green when power is connected
5
HDMI IN Connector
Connect to an HDMI source, (for example, a PC)
6
HDMI OUT Connector
Connect to an HDMI acceptor, (for example, a UHD smart TV)
7
PROGRAM DIP-Switches
Set the device behavior, (see Configuring the on page 6)
8
5V DC Power Connector
Connect to the supplied power adapter

Kramer Electronics Ltd.
PT‑2C –Connecting the PT‑2C
5
Connecting the PT‑2C
Always switch off the power to each device before connecting it to your PT‑2C. After
connecting your PT‑2C, connect its power and then switch on the power to each device.
Figure 2: Connecting the PT‑2C Extended EDID Processor
To connect the PT‑2C, as illustrated in the example in Figure 2:
1. Connect the HDMI source (for example, a PC) to the HDMI IN connector.
2. Connect the HDMI OUT connector to an HDMI acceptor (for example, a display).
3. Connect the USB port to a laptop running EDID Designer to modify the EDID, or to a PC
to upgrade the firmware of the PT‑2C.

Kramer Electronics Ltd.
PT‑2C –Connecting the PT‑2C
6
Configuring the PT‑2C
1. The 8-way Program DIP-switch on the rear panel is used to configure the PT‑2C according
to the following table.
Note that all the DIP-switches are set to off (up) by default.
DIP
Feature
Function
1
Lock the EDID
On (down) —EDID pass-through mode
Off (up) —EDID Locked
When EDID is locked, the audio parameters are set as defined by DIP-switch
3. In pass-through mode, the DIP-switch 3 setup is ignored
The Audio DIP-switch (3) setup is implemented only upon setting DIP-
switch 1 to off (up), locking the EDID
2
Deep color
On—Passes the deep color parameters (down)
Off—Limits deep color to 8 bits per color (up)
3
Audio setup
On—Passes the audio parameters (down)
Off—Limits the audio to 2-channel LPCM (up)
This setup is enabled only after DIP-switch 1 is set to Off (EDID locked).
4
HDCP operation
On—Passes HDCP (down)
Off—HDCP off (up)
When On, if the sink supports HDCP, the input declares HDCP support. It will
then handle HDCP on the output and input actively. If the sink does not support
HDCP then the input will not support HDCP.
When Off, the device does not support HDCP on its input, even if HDCP is
detected on the output.
5
Color space
On—Passes color space (down)
Off—Forces RGB color space (up)
6/7
Set output 5V
shutdown
6
Off
On
Off
On
7
Off
Off
On
On
Delay before 5V
output
cut-off
Always on
5s
1m
15m
The PT‑2C can power off the HDMI 5V output to let the connected device enter the sleep mode if
there is no source connected. The power off delay time is controlled by DIP-switches 6 and 7 (0 =
up/Off; 1 = down/On)
8
Reserved (always set to off)

Kramer Electronics Ltd.
PT‑2C –Connecting the PT‑2C
7
EDID loading/storing
The EDID DIP-switch 1 determines the behavior of EDID on the device.
The Pass-through Mode
In the pass-through mode (DIP-switch 1 set to on), the EDID of the connected output (a
display in the following examples) is automatically loaded to the PT‑2C.
If the display is replaced, the PT‑2C captures the new EDID from the new display. Any
change in the output automatically changes the EDID that is stored in the
PT‑2C.
When disconnecting the output, the last EDID remains stored in the PT‑2C.
The EDID Lock Mode
When in the Lock mode (DIP-switch 1 set to off), the current EDID is locked and remains
unchanged even if the display is replaced on the output.
When in the lock mode the audio setup is determined by the DIP-switch 3 Audio setup.
You can connect a PC to the EDID DESIGNER/F/W UPDATE Mini USB port to modify the
EDID via the Kramer EDID designer software.
Note that when using EDID designer to modify the EDID (in the Lock mode), the DIP-switch
3 status is ignored.
Setting the default EDID
You can set the PT‑2C to its EDID default value.
To set the default EDID:
1. Make sure the PT‑2C is set to the Pass-through mode
2. Disconnect the output.
3. Set DIP-switch 1 to the Lock mode (off).
The default EDID is loaded

Kramer Electronics Ltd.
PT‑2C –Default EDID
8
Default EDID
Monitor
Model name............... PT-2C
Manufacturer............. KMR
Plug and Play ID......... KMR1200
Serial number............ n/a
Manufacture date......... 2015, ISO week 255
Filter driver............ None
-------------------------
EDID revision............ 1.3
Input signal type........ Digital
Color bit depth.......... Undefined
Display type............. RGB color
Screen size.............. 520 x 320 mm (24.0 in)
Power management......... Standby, Suspend, Active off/sleep
Extension blocs.......... 1 (CEA-EXT)
-------------------------
DDC/CI................... Supported
MCCS revision............. 2.1
Display technology....... TFT
Controller............... STMicro 0x9301
Firmware revision........ 2.1
Firmware flags........... 0x006645CC
Active power on time..... Not supported
Power consumption........ Not supported
Current frequency........ 74.20kHz, 60.20Hz
Color characteristics
Default color space...... Non-sRGB
Display gamma............ 2.20
Red chromaticity......... Rx 0.674 - Ry 0.319
Green chromaticity....... Gx 0.188 - Gy 0.706
Blue chromaticity........ Bx 0.148 - By 0.064
White point (default).... Wx 0.313 - Wy 0.329
Additional descriptors... None
Timing characteristics
Horizontal scan range.... 30-83kHz
Vertical scan range...... 56-76Hz
Video bandwidth.......... 170MHz
CVT standard............. Not supported
GTF standard............. Not supported
Additional descriptors... None
Preferred timing......... Yes
Native/preferred timing.. 1280x720p at 60Hz (16:10)
Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
Standard timings supported
720 x 400p at 70Hz - IBM VGA
720 x 400p at 88Hz - IBM XGA2
640 x 480p at 60Hz - IBM VGA
640 x 480p at 67Hz - Apple Mac II
640 x 480p at 72Hz - VESA
640 x 480p at 75Hz - VESA
800 x 600p at 56Hz - VESA
800 x 600p at 60Hz - VESA
800 x 600p at 72Hz - VESA
800 x 600p at 75Hz - VESA

Kramer Electronics Ltd.
PT‑2C –Default EDID
9
832 x 624p at 75Hz - Apple Mac II
1024 x 768i at 87Hz - IBM
1024 x 768p at 60Hz - VESA
1024 x 768p at 70Hz - VESA
1024 x 768p at 75Hz - VESA
1280 x 1024p at 75Hz - VESA
1152 x 870p at 75Hz - Apple Mac II
1280 x 1024p at 75Hz - VESA STD
1280 x 1024p at 85Hz - VESA STD
1600 x 1200p at 60Hz - VESA STD
1024 x 768p at 85Hz - VESA STD
800 x 600p at 85Hz - VESA STD
640 x 480p at 85Hz - VESA STD
1152 x 864p at 70Hz - VESA STD
1280 x 960p at 60Hz - VESA STD
EIA/CEA-861 Information
Revision number.......... 3
IT underscan............. Supported
Basic audio.............. Supported
YCbCr 4:4:4.............. Supported
YCbCr 4:2:2.............. Supported
Native formats........... 1
Detailed timing #1....... 1920x1080p at 60Hz (16:10)
Modeline............... "1920x1080" 148.500 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync
Detailed timing #2....... 1920x1080i at 60Hz (16:10)
Modeline............... "1920x1080" 74.250 1920 2008 2052 2200 1080 1084 1094 1124 interlace +hsync
+vsync
Detailed timing #3....... 1280x720p at 60Hz (16:10)
Modeline............... "1280x720" 74.250 1280 1390 1430 1650 720 725 730 750 +hsync +vsync
Detailed timing #4....... 720x480p at 60Hz (16:10)
Modeline............... "720x480" 27.000 720 736 798 858 480 489 495 525 -hsync -vsync
CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz
CE video identifiers (VICs) - timing/formats supported
1920 x 1080p at 60Hz - HDTV (16:9, 1:1)
1920 x 1080i at 60Hz - HDTV (16:9, 1:1)
1280 x 720p at 60Hz - HDTV (16:9, 1:1) [Native]
720 x 480p at 60Hz - EDTV (16:9, 32:27)
720 x 480p at 60Hz - EDTV (4:3, 8:9)
720 x 480i at 60Hz - Doublescan (16:9, 32:27)
720 x 576i at 50Hz - Doublescan (16:9, 64:45)
640 x 480p at 60Hz - Default (4:3, 1:1)
NB: NTSC refresh rate = (Hz*1000)/1001
CE vendor specific data (VSDB)
IEEE registration number. 0x000C03
CEC physical address..... 1.0.0.0
Maximum TMDS clock....... 165MHz
CE speaker allocation data
Channel configuration.... 2.0
Front left/right......... Yes
Front LFE................ No
Front center............. No
Rear left/right.......... No
Rear center.............. No
Front left/right center.. No
Rear left/right center... No
Rear LFE................. No
Report information

Kramer Electronics Ltd.
PT‑2C –Default EDID
10
Date generated........... 2/16/2016
Software revision........ 2.60.0.972
Data source.............. Real-time 0x0041
Operating system......... 6.1.7601.2.Service Pack 1
Raw data
00,FF,FF,FF,FF,FF,FF,00,2D,B2,00,12,00,00,00,00,FF,19,01,03,80,34,20,78,EA,B3,25,AC,51,30,B4,26,
10,50,54,FF,FF,80,81,8F,81,99,A9,40,61,59,45,59,31,59,71,4A,81,40,01,1D,00,72,51,D0,1E,20,6E,28,
55,00,07,44,21,00,00,1E,00,00,00,FD,00,38,4C,1E,53,11,00,0A,20,20,20,20,20,20,00,00,00,FC,00,50,
54,2D,32,43,20,20,20,20,20,20,20,20,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,01,CD,
02,03,1B,F1,23,09,07,07,48,10,05,84,03,02,07,16,01,65,03,0C,00,10,00,83,01,00,00,02,3A,80,18,71,
38,2D,40,58,2C,45,00,07,44,21,00,00,1E,01,1D,80,18,71,1C,16,20,58,2C,25,00,07,44,21,00,00,9E,01,
1D,00,72,51,D0,1E,20,6E,28,55,00,07,44,21,00,00,1E,8C,0A,D0,8A,20,E0,2D,10,10,3E,96,00,07,44,21,
00,00,18,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,00,47

Kramer Electronics Ltd.
PT‑2C –Technical Specifications
11
Technical Specifications
INPUT:
1 HDMI connector
OUTPUT:
1 HDMI connector
PORTS:
1 Mini USB
MAX DATA RATE:
10.2Gbps (3.4Gbps per data channel)
STANDARDS SUPPORTED:
Supports HDMI and HDCP
CONTROLS:
8 DIP-switches
STANDARDS:
HDMI with Deep Color, x.v.Color™ and 3D
HDCP—works with sources that support HDCP repeater mode
INDICATOR LEDS:
HDMI In, HDMI Out, Power
POWER CONSUMPTION:
5V DC 315mA
OPERATING TEMPERATURE:
0° to +40°C (32° to 104°F)
STORAGE TEMPERATURE:
–40° to +70°C (–40° to 158°F)
HUMIDITY:
10% to 90%, RHL non-condensing
COOLING:
Convection
ENCLOSURE TYPE:
Aluminum
RACK MOUNT:
With optional adapter (RK−4PT)
FURNITURE MOUNT:
With included rubber feet
DIMENSIONS:
6.22cm x 5.18cm x 2.44cm (2.45" x 2.04" x 0.96") W, D, H.
PRODUCT WEIGHT:
0.1kg (0.22lbs) approx.
SHIPPING WEIGHT:
0.4kg (0.88lbs) approx.
INCLUDED ACCESORRIES:
Power supply (5V DC)
OPTIONS:
RK−4PT 19" rack adapter
Specifications are subject to change without notice at www.kramerav.com

Kramer Electronics Ltd.
PT‑2C –Technical Specifications
12
Supported Resolutions
Resolution
Refresh Rate
Comments
640x480p
85Hz; 75Hz; 72Hz; 60Hz; 59.95Hz
59.95Hz is available on quantum 780B
720x480p
60Hz
720x576p
50Hz
800x600p
85Hz; 75Hz; 72Hz; 60Hz
848x480p
60Hz
“CVT(R)0860H” on quantum
852x480p
60Hz
available on quantum 780B
1024x768p
85Hz; 75Hz; 70Hz; 60Hz
1280x960
60Hz
1280x1024p
75Hz; 60Hz
1280x768p
60Hz
available on quantum 780B
1280x800p
60Hz
“DMR(T)1260D” on quantum
1920x1080p
50Hz; 60Hz; 30Hz; 24Hz;
“1080p30” on quantum
1920x1080p
60Hz;
Deep color
1920x1080i
50Hz; 60Hz;
1600x1200p
60Hz
1600x900p
60Hz
“DMR1660H” on quantum
1152x864p
75Hz
1440x900p
60Hz
1680x1050p
60Hz
1360x768p
60Hz
1366x768
60Hz; 50Hz
1400x1050p
60Hz
720x480i
30Hz
available on quantum 780B
3840x2160
30Hz
4096x2160
30Hz

The warranty obligations of Kramer Electronics Inc. (“Kramer Electronics”) for this product are limited to the terms set forth below:
What is Covered
This limited warranty covers defects in materials and workmanship in this product.
What is Not Covered
This limited warranty does not cover any damage, deterioration or malfunction resulting from any alteration, modification, improper or unreasonable use
or maintenance, misuse, abuse, accident, neglect, exposure to excess moisture, fire, improper packing and shipping (such claims must be presented to
the carrier), lightning, power surges, or other acts of nature. This limited warranty does not cover any damage, deterioration or malfunction resulting
from the installation or removal of this product from any installation, any unauthorized tampering with this product, any repairs attempted by anyone
unauthorized by Kramer Electronics to make such repairs, or any other cause which does not relate directly to a defect in materials and/or workmanship
of this product. This limited warranty does not cover cartons, equipment enclosures, cables or accessories used in conjunction with this product.
Without limiting any other exclusion herein, Kramer Electronics does not warrant that the product covered hereby, including, without limitation, the
technology and/or integrated circuit(s) included in the product, will not become obsolete or that such items are or will remain compatible with any other
product or technology with which the product may be used.
How Long this Coverage Lasts
The standard limited warranty for Kramer products is seven (7) years from the date of original purchase, with the following exceptions:
1. All Kramer VIA hardware products are covered by a standard three (3) year warranty for the VIA hardware and a standard three (3) year
warranty for firmware and software updates.
2. All Kramer fiber optic cables, adapter-size fiber optic extenders, active cables, cable retractors, all Kramer speakers and Kramer touch panels
are covered by a standard one (1) year warranty.
3. All Kramer Cobra products, all Kramer Calibre products, all Kramer Minicom digital signage products, all HighSecLabs products, all
streaming, and all wireless products are covered by a standard three (3) year warranty.
4. All Sierra Video MultiViewers are covered by a standard five (5) year warranty.
5. Sierra switchers & control panels are covered by a standard seven (7) year warranty (excluding power supplies and fans that are covered for
three (3) years).
6. K-Touch software is covered by a standard one (1) year warranty for software updates.
7. All Kramer passive cables are covered by a ten (10) year warranty.
Who is Covered
Only the original purchaser of this product is covered under this limited warranty. This limited warranty is not transferable to subsequent purchasers or
owners of this product.
What Kramer Electronics Will Do
Kramer Electronics will, at its sole option, provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper
claim under this limited warranty:
1. Elect to repair or facilitate the repair of any defective parts within a reasonable period of time, free of any charge for the necessary parts and
labor to complete the repair and restore this product to its proper operating condition. Kramer Electronics will also pay the shipping costs
necessary to return this product once the repair is complete.
2. Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same
function as the original product.
3. Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought
under this limited warranty.
What Kramer Electronics Will Not Do Under This Limited Warranty
If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer
Electronics products, this product must be insured during shipment, with the insurance and shipping charges prepaid by you. If this product is returned
uninsured, you assume all risks of loss or damage during shipment. Kramer Electronics will not be responsible for any costs related to the removal or re-
installation of this product from or into any installation. Kramer Electronics will not be responsible for any costs related to any setting up this product, any
adjustment of user controls or any programming required for a specific installation of this product.
How to Obtain a Remedy Under This Limited Warranty
To obtain a remedy under this limited warranty, you must contact either the authorized Kramer Electronics reseller from whom you purchased this
product or the Kramer Electronics office nearest you. For a list of authorized Kramer Electronics resellers and/or Kramer Electronics authorized service
providers, visit our web site at www.kramerav.com or contact the Kramer Electronics office nearest you.
In order to pursue any remedy under this limited warranty, you must possess an original, dated receipt as proof of purchase from an authorized Kramer
Electronics reseller. If this product is returned under this limited warranty, a return authorization number, obtained from Kramer Electronics, will be
required (RMA number). You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product.
If it is decided that this product should be returned directly to Kramer Electronics, this product should be properly packed, preferably in the original
carton, for shipping. Cartons not bearing a return authorization number will be refused.
Limitation of Liability
THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID
FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY LAW, KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL
THEORY. Some countries, districts or states do not allow the exclusion or limitation of relief, special, incidental, consequential or indirect damages, or
the limitation of liability to specified amounts, so the above limitations or exclusions may not apply to you.
Exclusive Remedy
TO THE MAXIMUM EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. TO THE MAXIMUM EXTENT
PERMITTED BY LAW, KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION,
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR
EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW, THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT, INCLUDING WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPLICABLE LAW.
IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A “CONSUMER PRODUCT” UNDER THE MAGNUSON-MOSS WARRANTY ACT (15
U.S.C.A. §2301, ET SEQ.) OR OTHER APPLICABLE LAW, THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU, AND
ALL IMPLIED WARRANTIES ON THIS PRODUCT, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE,
SHALL APPLY AS PROVIDED UNDER APPLICABLE LAW.
Other Conditions
This limited warranty gives you specific legal rights, and you may have other rights which vary from country to country or state to state.
This limited warranty is void if (i) the label bearing the serial number of this product has been removed or defaced, (ii) the product is not distributed by
Kramer Electronics or (iii) this product is not purchased from an authorized Kramer Electronics reseller. If you are unsure whether a reseller is an
authorized Kramer Electronics reseller, visit our web site at www.kramerav.com or contact a Kramer Electronics office from the list at the end of this
document.
Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the
online product registration form. Kramer Electronics thanks you for purchasing a Kramer Electronics product. We hope it will give you years of
satisfaction.

www.KramerAV.com
[e-mail]
P/N:
2900-300494
Rev:
3
SAFETY WARNING
Disconnect the unit from the power supply before opening andservicing
For the latest information on our products and a list of Kramer distributors, visit our Web site where
updates to this user manual may be found.
We welcome your questions, comments, and feedback.