Kramer VP-427H2 User manual

VP
-427H2 Quick Start (P/N: 2900-300831QS REV 4)
P/N:
2900- 300831QS
Rev:
4
Scan for full manual
VP-427H2 Quick Start Guide
This guide helps you install and use your VP-427H2 for the first time.
Go to www.kramerav.com/downloads/VP-427H2 to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
VP-427H2 4K HDBT to HDMI Receiver/Scaler
1 Bracket set
1 Quick start guide
1 Power adapter and cord
4 Rubber feet
Step 2: Get to know your VP-427H2
#
Feature
Function
1
PROG USB Connector
Connects to a USB memory stick for programming upgrade
2
ON LED
Lights green when the unit is powered on
3 MENU Button Press to enter/exit the on-screen display (OSD) menu. Press together with the –
button to reset to 1080p
4 ENTER Button In OSD, press to choose the highlighted menu item. Press together with the
+/FREEZE button to reset to XGA
5
–
In OSD, press to move back through the list or to decrement the parameter value
6 +/FREEZE Button In OSD, press to move forward through the list or to increment the parameter value.
When not in OSD, press to freeze the display
7 HDBT IN RJ-45 Connector Connects to an HDBaseT transmitter
8 IR IN 3.5mm Mini Jack Connects to an IR sensor
9
IR OUT 3.5mm Mini Jack
Connects to an IR emitter
10 RS-232 9-pin D-sub Connector Connects to an acceptor to embed/de-
embed control commands in the HDBaseT data
stream
11 HDMI OUT Connector Connects to an HDMI acceptor
12 AUDIO OUT 3.5mm Mini Jack Connects to an unbalanced stereo audio acceptor
13
ETHERNET RJ-45 Connector
Connect to a PC via a LAN
14
5V DC
+5V DC connector for powering the unit
All manuals and user guides at all-guides.com
all-guides.com

Step 3: Install the VP-427H2
Install VP-427H2 using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to www.kramerav.com/downloads/VP-427H2.
•Mount the unit in a rack using an optional RK-T2B rack adapter.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VP-427H2. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the VP-427H2.
Step 5: Connect the power
Connect the 5V DC power adapter to the VP-427H2 and plug the adapter into the mains.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the Kramer Electronics power supply that is provided with the unit.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.
Technical Specifications
Inputs: 1 HDBaseT twisted pair on an RJ-45 connector, 1 IR on a 3.5mm mini jack
Outputs: 1 HDMI connector, 1 IR on a 3.5mm mini jack, 1 unbalanced stereo audio (1.2Vrms nominal, 100Ω)
on a 3.5mm mini jack
Ports: 1 bidirectional RS-232 port on a 9-pin D-sub connector, 1 Ethernet on an RJ-45 connector,
1 USB (A) for upgrading
Compliance with HDMI
Standard:
Supports up to HDMI 2.0, and HDCP 2.2
Output Resolutions: 640x480@60Hz, 800x600@60Hz 1024x768@60Hz, 1280x768@60Hz, 1360x768@60Hz,
1280x800@60Hz, 1280x1024@60Hz, 1440x900@60Hz, 1400x1050@60Hz, 1680x1050@60Hz,
1600x1200@60Hz, 1920x1200@60Hz 480P@60Hz, 576P@50Hz, 720P@50/60Hz,
1080P@24/25/30Hz, 4k2k@24/25/30Hz, 4k2k (4:2:0)@50/60Hz, 4k2k (4:4:4)@50/60Hz, Native
Output Refresh Rate: 60Hz for computer graphics resolutions, 50/60Hz for HDTV resolutions
Audio Sampling Rate:
48kHz for analog audio output
Video Latency:
Progressive input: 30ms (approx.); interlaced input: 50ms (approx.)
Embedded Audio: HDMI and HDBT support multi-channel audio
RS-232 Baud Rate: 115200bps max.
Controls:
Front panel buttons, OSD menu
Indicators:
ON LED (green)
Power Consumption: 5V DC, 2.5A Power Source: 5.2V/4A
Operating Temperature: 0° to +40°C (32° to 104°F) Storage Temperature: -40° to +70°C (-40° to 158°F)
Humidity:
10% to 90%, RHL non-condensing
Dimensions:
18.8cm x 11.4cm x 2.5cm (7.4” x 4.5” x 1.0”) W, D, H
Shipping Dimensions: 35.1cm x 21.2cm x 7.2cm (13.8” x 8.35” x 2.8”) W, D, H
Weight: 0.56kg (1.2lb) Shipping Weight: 1.1kg (2.42lb)
Included Accessories:
Power supply
Options:
RK-T2B 19” rack adapter
Specifications are subject to change without notice at www.kramerav.com
All manuals and user guides at all-guides.com