Kramer VS-21DTP User manual

VS-21DTP Quick Start (P/N: 2900-300924QS REV 1)
P/N:
2900- 300924QS
Rev:
1
Scan for full manual
VS-21DTP Quick Start Guide
This guide helps you install and use your VS-21DTP for the first time.
Go to www.kramerav.com/downloads/VS-21DTP to download the latest user manual and check if
firmware upgrades are available.
Step 1: Check what’s in the box
VS-21DTP 2xHDMI to HDBT Standby Switcher/POE
4 Rubber feet
1 Bracket set
1 Power adapter and cord
1 Quick start guide
Step 2: Get to know your VS-21DTP
#
Feature
Function
1
ACTIVE INPUT LEDs (1 to 2)
Lights green when the input is active. Both LEDs flash when no input is active.
2
PRIORITY LED
Lights green when DIP-switch 1 is set to PRIORITY (down).
3
LAST CONNECTED LED
Lights green when DIP-switch 1 is set to LAST CONNECTED (up).
4
POE STATUS LED
Lights green when the unit provides PoE.
5
ON LED
Lights green when the unit is powered on via power adapter or PoE.
6
INPUT HDMI Connectors (1 to 2)
Connect to an HDMI source.
7
HDBT OUT RJ-45 Connector
Connect to an HDBaseT receiver (for example, TP-580R) and provide or
accept power (bidirectional PoE).
8
LAST CONN/PRIORITY DIP-switch 1
Set DIP-switch 1 up (off) to select the Last Connected input.
Set DIP-switch 1 down (on) to select the Priority input determined by
DIP-switch 2.
9
DEF 1/DEF 2 DIP-switch 2
Set DIP-switch 2 up (off) to define INPUT 1 as the default (priority) input.
Set DIP-switch 2 down (on) to define INPUT 2 as the default (priority) input.
10
REMOTE 3-pin Terminal Block Connector
Connects to optional contact closure switches 1 or 2 for manual switching (by
momentary contact between the desired pin and the G pin).
11
48V DC Power Terminal Block Connector
Connect to the Kramer power adapter.

Step 3: Install VS-21DTP
Install VS-21DTP using one of the following methods:
Attach the rubber feet and place the unit on a flat surface.
Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to www.kramerav.com/downloads/VS-21DTP.
Mount the unit in a rack using an optional RK-3T rack adapter.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your VS-21DTP. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to VS-21DTP.
DIP-switches Setup:
A switch that is down is on; a switch that is up is off. By default, both switches are up (off).
Video Switching Selection:
DIP-switch 1
DIP-switch 2
Video Input Selection
PRIORITY (down)
DEF 1 (up)
INPUT 1 is the default priority setup and is automatically switched to the
output.
DEF 2 (down)
INPUT 2 is the default priority setup and is automatically switched to the
output.
LAST CONNECTED (up)
N/A
The last connected source is switched to the output (a reactivated or
reconnected source becomes the new “Last Connected” source).
Contact Closure Switches (Manual Override):
Controlling via the remote contact closure pushbuttons overrides all DIP-switch settings and automatic switching until the manually
selected source disconnects, becomes inactive or the VS-21DTP is powered off.
Select INPUT 1
Momentarily connect REMOTE IN 1 to PIN G (ground).
Select INPUT 2
Momentarily connect REMOTE IN 2 to PIN G (ground).
Step 5: Connect the power
Connect the 48V DC power supply to VS-21DTP and plug it into the mains electricity or accept power over Ethernet (PoE) from an
HDBaseT receiver via PoE.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the power cord that is supplied with the unit.
Warning:
Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information.