Kraus Esta KVF-1210-2PK User manual

Esta™ Single Handle Lavatory Faucet
KVF-1210
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV. JUN 06, 2019

Congratulations on the purchase of your new
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [e-mail]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
1

Prior to Installation:
•Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-775-
0703 for a replacement
•
•Pre-drilled countertop hole size requirement: 1-3/8”(min)
•Max countertop thickness: 2 7/8”
Tools you will need:
13
Wrench Phillips Screwdriver Safety Goggles
Silicone Sealant
(optional)
Pipe Tape
2
Turn off the hot and cold water lines at the angle stops and turn on the old faucet
to release any built-up pressure

3
A. Faucet Body
C. Aerator Key
D. Plastic Washer
F. Mounting Nut
I
A
Diagram and Parts List
D
E
F
G. Screws
H
H. Hex Wrench
B
B. Aerator
G
I. Drain
C
E. Metal Washer

4
Faucet Dimension
Installer Tip:
9/16-24UNEF-2B
M18.5X1.0-6g
12"
[305.0mm]
2 1/2"
[62.7mm]
2 7/8"
[73.0mm]
5 1/8"
[130.1mm]
6 7/8"
[173.2mm]
8 7/8"
[226.8mm]
2 1/8"
[54.8mm]

5
Drain Dimension
Installer Tip:
G1 1/4-11
Ø1 1/4"
[31.7mm]
5/8"~2 3/8"
[15.8mm~61.6mm]
2 3/4"
[69.0mm]
Ø2 3/8"
[61.1mm]
6 3/4"
[172.5mm]

Step 1: Remove washers and mounting nut
Shut off the water supply. Remove the
old faucet. Clean the mounting surface.
Remove the mounting nut & screws (F&G),
metal washer (E) and plastic washer (D)
from the faucet (A).
Step 2: Installing the faucet
Place faucet (A) through the hole in countertop.
Secure the faucet (A) to the countertop using
the plastic washer (D), metal washer (E) and
mounting nut (F) provided. Tighten screws (G).
E
6
F&G
A
D
E
G
D
A
F
G

7
Step 3: Connect waterlines to main valve
Attach waterlines to angle stops
and tighten until snug. Turn on angles
stops and check for leaks (DO NOT TURN
FAUCET ON)
Step 4: Install Press pop-up assembly
2
3
6
7
4
5
1
Unscrew the nut (6) from the pop-up
body (2), move over the tail pipe (7)
and washer (5), then unscrew the
coupling nut (4) and remove the
washer (3).

Step 5: Flush faucet
8
Step 4: Install Press pop-up assembly
2
3
4
1
6
7
5
Place the washer (1) underneath the
flange of the pop-up body (2). Slide
the pop-up body (2) down through
the drain hole on the vessel or basin.
From underside, slide the washer (3)
against the bottom of the vessel or
basin, thread on the coupling nut (4)
and tighten. Do not overtighten.
Slide the nut (6) over the tail pipe (7).
Place the washer (5) into the nut and
tighten. Do not overtighten.
After installing faucet, remove aerator (B)
with included aerator key (C). Turn water
on for 30 seconds to remove any debris.
Reassemble aerator (B).
B
C

9
Replacement Parts
1. Cover Button
Replacement Parts List Part #
2. Set Screw
3. Handle
5. Bonnet Nut
6. Screw
7. Cartridge
8. Aerator
10. Plastic Washer
11. Metal Washer
12. Mounting Nut & Screw
Finish / Color
SFS, MB,
GM, BG*
KP27152
KP27153
KP27069
KP27051
KP27052
KP27146
KP27147
KP27002
KP27001
KP27150
3
1
11
12
13
9. Aerator Key
4. Cap SFS, MB,
GM, BG* KP27151
13. Hex Wrench
KP27148
1
2
3
4
5
6
7
13
8
10
11
12
14 SFS, MB,
GM, BG*
KP27020
GR, BL*
9
14. Drain KP27059
*Denotes faucet component color options:
SFS - Spot Free Stainless Steel
MB - Matte Black
GM - Gunmetal
BG - Brushed Gold
GR - Grey
BL - Black