Kraus KE1US32 User manual

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2020 Kraus USA Inc. I REV. January 18, 2021
KEU12 / KEU14/ KE1US21 / KE1US32
Porcelain Enameled Steel
Undermount Kitchen Sinks
R
INSTALLATION MANUAL

Congratulations on the purchase of your new
Kraus plumbing fixture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:
2
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

Prior to Installation:
·Make sure that you have all necessary parts by checking the parts list.
If any part is missing or damaged, please contact Kraus Customer
Service at 800-775-0703 for a replacement.
·Inspect the sink prior to installation to make sure that it has not been
damaged during shipping.
·Use the cut-out template provided by Kraus.
·Observe all plumbing and building codes according to your state
requirements.
·Not recommended to be installed with laminate countertop.
3
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for installing a
Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to
install all Kraus products by hiring a licensed professional.

4
Parts List
·Cut-out Template
·Mounting Hardware
Tools you will need:
4
NOTE: Specialized tools may be necessary to install Kraus Porcelain Enameled
Steel Undermount sinks with countertop materials other than wood, marble or
granite.
Safety Goggles Silicone Adhesive Jig Saw
Phillips Screwdriver Tape Measure Pencil
Drill Scissors
Screwdriver Putty Knife

55
Dimensions
19 3/4" (500mm)
21 1/4" (540mm)
15 3/4" (400mm)
17 3/8" (440mm)
7 3/4"
(195mm)
KE1US21
21 1/4” x 17 3/8” x 7 3/4”
Min Cabinet Size: 24”
R3/4"
(20mm)
R1 5/8"
(40mm)
7 1/2"
(190mm)
R3/4"
(20mm)
KEU12
23" x 17 1/2" x 9"
Min Cabinet Size: 27"
KEU14
31 1/2" x 18 3/8" x 10"
Min Cabinet Size: 36"
17 1/2"
(445mm)
15 7/8"
(403mm)
21" (534mm)
23" (584mm)
9"
(230mm)
10"
(255mm)
18 3/8"
(467mm)
16 1/4"
(413mm)
29 1/2" (750mm)
31 1/2" (800mm)
R3 1/2"
(90mm) R3 1/2"
(90mm)
KE1US32
30 1/2” x 19” x 7 7/8”
Min Cabinet Size: 36”
R3/4"
(20mm)
R1 5/8"
(40mm)
R3/4"
(20mm)
30" (766mm)
31 1/2" (800mm)
17 3/4" (451mm)
19" (485mm)
8 1/8"
(206mm)
7 3/4"
(195.5mm)
7 7/8"
(199mm)

6
1. Determine Reveal Type
Use scissors to cut along the line of the paper template for your desired
reveal type (Negative, Positive or Flushed Reveal).
6
3/8“ Positive Reveal
Flushed/Zero Reveal
1/8“ Negative Reveal
KRAUS Recommended Installation Type
3/8”POSITIVE
1/8”NEGATIVE
FLUSHED/ZERO
Centerline

7
2. Position Template
·Check the cut-out template against the actual sink to ensure a proper
sized cut-out.
·Place the cut-out template in the desired location on the countertop.
NOTE: Make sure clearance is suitable for backsplash, faucet and plumbing for the sink.
3. Trace Template
·Trace template on countertop with a pencil.

8
4. Cut Countertop
·Cut the opening in the countertop by carefully following the traced line.
NOTE: Please use the appropriate saw that best fits your countertop material.

9
5. Set up Mounting Brackets
·Turn countertop over and align sink with countertop. Decide location for
mounting brackets.
·Mounting holes should be 1/2" from edge of sink.
6. Drill Hole in Countertop
·Drill 3/8" diameter x 1/2" deep hole in countertop.
1/2"
(13mm)
3/8 1/2

10
7. Install Anchors
·Insert anchors into drilled holes and lightly tap with a hammer until flush.
8. Secure Sink to Countertop
·Use a bead of silicone (or preferred adhesive) around the rim of the sink.
Check the alignment of the sink to the cutout in the countertop. Place sink
over cutout hole and press firmly.