Kraus KPF-1630 User manual

INSTALLATION MANUAL
www.kraususa.com I toll free: 1.800.775.0703 I © 2013-2014 Kraus USA Inc.
Single Lever Pull-Down
Kitchen Faucet
KPF-1630

Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satised with your purchase, and enjoy it for years
to come. If you have any questions, or require technical assistance, please contact
us at 800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service

Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts
list. If any part is missing or damaged, please contact Kraus Customer
Service at 800-775-0703 for a replacement
• Turn o the cold and hot water at the angle stops and turn on the old
faucet to release any built up pressure
• Flush angle stops to release any debris prior to installation
• Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
• Max countertop thickness: 1-3/8
• 1, 2, or 3 hole installation
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [e-mail]

Diagram and Parts List
1
9
11
10
4A
3A
7
8A
2
5
6
12
8B
3B
4B
4C

Diagram and Parts List Tools you will need
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8
Adjustable Wrench
Phillips Screwdriver
Safety Goggles
Silicone Sealant
(optional)
1. Spray Head
2. Faucet Body
3. Deck Plate Assembly
A. Deck Plate
B. Base Plate
4. Mounting Hardware
A. Rubber & Metal Washer
B. Mounting Nut
C. Mounting Screws
5. Spray Hose
6. Weight
7. Check Valve
8. Hot and Cold Copper Lines
A. Cold
B. Hot
9. Aerator Key
10. Hex Wrench
11. Faucet Extender
12. Washer

Faucet Installation Procedure
Installer Tip:
Shut o main water supply before installing new faucet
9-1/4”
(233.8mm)
6-3/4”
(170.5mm) 2-7/8”
(73mm)
9-1/4”
(236mm)
5-3/8”
(136mm)
18-5/8”
(472.3mm)
4-7/8”
(125mm)
5º
8-3/8”
(211.4mm)
4”
(100.5mm)
MAX 2"
(113mm)
(4-1/2")
MAX51
mm
9-1/4”
(233.8mm)
6-3/4”
(170.5mm) 2-7/8”
(73mm)
9-1/4”
(236mm)
5-3/8”
(136mm)
18-5/8”
(472.3mm)
4-7/8”
(125mm)
5º
8-3/8”
(211.4mm)
4”
(100.5mm)
MAX 2"
(113mm)
(4-1/2")
MAX51mm

Step 1: Remove mounting hardware
Remove the mounting
screws (4C), mounting nut
(4B), and rubber & metal
washer (4A) from the
mounting pipe
Step 2A: Faucet installation - with deck plate
For three-hole installation:
Deck plate (3A), base plate
(3B), and silicone sealant
(optional) are required
STEP1 STEP 2A STEP 2B STEP 3
STEP 4 STEP 5
STEP 6 STEP 7
STEP 8
4A
3A
3B
4B
4C
4B
4C
7
5
6
8
5
1
4A
4B
4C
STEP1 STEP 2A STEP 2B STEP 3
STEP 4 STEP 5
STEP 6 STEP 7
STEP 8
4A
3A
3B
4B
4C
4B
4C
7
5
6
8
5
1
4A
4B
4C

For single-hole installation:
Deck plate (3A), base plate
(3B), and silicone sealant
are NOT required
Step 3: Install faucet and mounting hardware
Insert faucet body (2) into
hole in countertop or deck
plate assembly (3). Install
mounting hardware (4A, B
&C) from underneath the
countertop
Step 2B: Faucet installation - without deck plate
STEP1 STEP 2A STEP 2B STEP 3
STEP 4 STEP 5
STEP 6 STEP 7
STEP 8
4A
3A
3B
4B
4C
4B
4C
7
5
6
8
5
1
4A
4B
4C
STEP1 STEP 2A STEP 2B STEP 3
STEP 4 STEP 5
STEP 6 STEP 7
STEP 8
4A
3A
3B
4B
4C
4B
4C
7
5
6
8
5
1
4A
4B
4C

Step 4: Secure mounting hardware
Adjust direction of faucet
body (2) so that handle is on
right side of faucet. Tighten
mounting nut (4B) until snug.
Tighten mounting screws
(4C) to nut with a Phillips
screwdriver until snug
Step 5: Attach spray hose and counterweight
Connect spray hose (5) to
check valve (7) attached to
supply line. Install weight
(6) on lowest vertical point
on spray hose (5)
STEP1 STEP 2A STEP 2B STEP 3
STEP 4 STEP 5
STEP 6 STEP 7
STEP 8
4A
3A
3B
4B
4C
4B
4C
7
5
6
8
5
1
4A
4B
4C
STEP1 STEP 2A STEP 2B STEP 3
STEP 4 STEP 5
STEP 6 STEP 7
STEP 8
4A
3A
3B
4B
4C
4B
4C
7
5
6
8
5
1
4A
4B
4C

Connect waterlines (not
included) to hot and cold
copper lines (8). Connect
waterlines (not included) to
angle stops. Tighten both
ends of waterlines with a
wrench until snug. Turn on
hot and cold angle stops
and check for leaks
Step 7: Flush spray hose
Step 8 Check for leaks
Remove spray head (1) from
spray hose (5). Hold tip of
spray hose (5). Turn faucet on
and let the water run for 60
seconds to ush any debris
Check for leaks at the
connections. Retighten if
necessary
Step 6: Connect waterlines
STEP1 STEP 2A STEP 2B STEP 3
STEP 4 STEP 5
STEP 6 STEP 7
STEP 8
4A
3A
3B
4B
4C
4B
4C
7
5
6
8
5
1
4A
4B
4C
STEP1 STEP 2A STEP 2B STEP 3
STEP 4 STEP 5
STEP 6 STEP 7
STEP 8
4A
3A
3B
4B
4C
4B
4C
7
5
6
8
5
1
4A
4B
4C
STEP1 STEP 2A STEP 2B STEP 3
STEP 4 STEP 5
STEP 6 STEP 7
STEP 8
4A
3A
3B
4B
4C
4B
4C
7
5
6
8
5
1
4A
4B
4C
NOTE: Please make sure
washer (12) is installed
attaching spray head to hose