Kraus KHF200-33 User manual

KHF200-30, KHF200-33, KHF200-36
KHF203-33, KHF203-36, KHF204-33
Stainless Steel Farmhouse
Kitchen Sinks
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV. October 26, 2020
R
INSTALLATION MANUAL

Congratulations on the purchase of your new Kraus plumbing fixture!
Please keep the box and packaging materials until your product is completely installed. If you have
any questions, require technical assistance or have any problems with your product:
2
Please contact our Customer Service Team
1-800-775-0703 / [email protected]
Have the model number available and retain a copy of your receipt with purchase date for
reference.
If for any reason this product does not meet your expectations, please be sure to repack this
product in the original box and packaging material to avoid damage during transit.
DO NOT RETURN TO STORE
STOP

3
Tools you will need:
NOTE: Specialized tools may be necessary to install Kraus Stainless Steel Kitchen sinks with
countertop materials other than wood, marble or granite.
Prior to Installation:
·Inspect the sink prior to installation to make sure the sink has not been damaged during
shipping
·Use the cut-out template provided by Kraus
·Observe all plumbing and building codes according to your state requirement
·Additional floor and wall preparation may be required to avoid damaging the product
·Make sure to purchase the correct cabinet for your farmhouse sink.
·Not recommended to be installed with laminate countertop
For technical assistance or replacement parts, please contact Kraus Customer Service
and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]
The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus sink. Should
there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a
licensed professional.
Safety Goggles Silicone Adhesive Jig Saw
Phillips Screwdriver Tape Measure Pencil
Drill Acetone
Screwdriver Level
Acetone

44
Parts List
KHF200-30
·Cut-Out Template
·Bottom Grid KBG-200-30
·Basket Strainer BST-1
KHF200-33
·Cut-Out Template
·Bottom Grid KBG-200-33
·Basket Strainer BST-1
KHF200-36
·Cut-Out Template
·Bottom Grid KBG-200-36
·Basket Strainer BST-1
KHF203-33
·Cut-Out Template
·Bottom Grids KBG-203-33-1 & KBG-203-33-2
·Strainer ST-1
·Basket Strainer BST-1
KHF203-36
·Cut-Out Template
·Bottom Grids KBG-203-36-1 & KBG-203-36-2
·Strainer ST-1
·Basket Strainer BST-1
KHF204-33
·Cut-Out Template
·Bottom Grids KBG-204-33-1 & KBG-204-33-2
·Strainer ST-1
·Basket Strainer BST-1

55
Dimensions:
Model #: KHF200-30
Sink Dimensions: 29 3/4” x 20 3/4” x 10”
Min Cabinet Size: 30”
Model #: KHF200-33
Sink Dimensions: 32 7/8” x 20 3/4” x 10”
Min Cabinet Size: 33”
Model #: KHF200-36
Sink Dimensions: 35 7/8” x 20 3/4” x 10”
Min Cabinet Size: 36”
29 3/4" (756mm)
20 3/4"
(527mm)
16"
(406mm)
3 1/2"
(90mm)
10"
(254mm)
9"
(229mm)
27" (686mm)
32 7/8" (835mm)
20 3/4"
(527mm)
16"
(406mm)
3 1/2"
(90mm)
10"
(254mm)
9"
(229mm)
30" (762mm)
35 7/8" (911mm)
20 3/4"
(527mm)
16"
(406mm)
3 1/2"
(90mm)
10"
(254mm)
9"
(229mm)
33" (838mm)

66
Dimensions:
Model #: KHF203-33
Sink Dimensions: 32 7/8” x 20 3/4” x 10”
Min Cabinet Size: 33”
Model #: KHF203-36
Sink Dimensions: 35 7/8” x 20 3/4” x 10”
Min Cabinet Size: 36”
Model #: KHF204-33
Sink Dimensions: 32 7/8” x 20 3/4” x 10”
Min Cabinet Size: 33”
32 7/8" (835mm)
17 3/8" (442mm)
20 3/4"
(527mm)
16"
(406mm)
3 1/2"
(90mm)
11 5/8"
(295mm)
10"
(254mm)
9"
(229mm)
32 7/8" (855mm)
11 5/8"
(295mm)
20 3/4"
(527mm)
16"
(406mm)
17 3/8" (442mm)
10"
(254mm)
9"
(229mm)
35 7/8" (911mm)
19" (483mm)
20 3/4"
(527mm)
16"
(406mm)
3 1/2"
(90mm)
13"
(330mm)
10"
(254mm)
9"
(229mm)

7
Step 1. Measure & Build Supports
·Measure the actual height of apron.
·Build supports on inside of cabinet based on sink measurements.
SUPPORTS
Installer Tip: Support Options
·1 1/4" Angle Irons
·(2) 2" x 4'
·3/4" Plywood

8
Step 2. Cut Cabinet Front
·Measure height of apron front. Add 1/16" to the dimension when you mark base cabinet front
cutout. Use jigsaw to cut.
Step 3. Install Sink
·Place sink in opening. The weight of sink should be sustained by the built supports.
·Make sure sink is leveled from front to back and side to side.
·Uses silicone to fill in gaps where necessary.

9
Step 4. Determine Reveal Type
·Use scissors to cut along the line of the paper template for your desired reveal type
(Negative, Positive, or Flushed Reveal)
KRAUS Recommended Installation Type
3/8” Positive Reveal
3/8” Positive
Flushed/Zero Reveal
Flushed/Zero
Centerline
1/8“ Negative Reveal
1/8” Negative

10
Step 5. Cut Countertop
·Use a bead of silicone (or preferred adhesive) around the rim of the Check the alignment of the
sink to the cutout in the countertop. Place countertop cutout hole over sink and press firmly.
Silicone Adhesive
Installer Tip: Use acetone or denatured alcohol to remove any excess sealant.