Kraus Cirrus FUS-13101 User manual

INSTALLATION MANUAL
Cirrus Single Lever Basin Faucet
FUS-13101
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 16, 2016

1
Thank you for your purchase
We would like to take this opportunity to thank you for choosing Kraus.
We hope that you are completely satised with your purchase, and enjoy it for years
to come. If you have any questions, or require technical assistance, please contact
us at 800.775.0703 and one of our representatives will be happy to help.
For more information about Kraus products, please visit:
www.kraususa.com
In order to activate your warranty and get faster access to customer support, please
register your new Kraus product at:
www.kraususa.com/registration
Sincerely,
Kraus USA Customer Service

2
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to ush any debris prior to installing new
plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
• Max countertop thickness: 1-3/8”
Tools you will need:
Adjustable Wrench Phillips Screwdriver Safety Goggles Bucket
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(
∅ 45mm)
∅ 1 15/16”
(
∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(
∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]

3
FUS-13101 Diagram and Parts List
H1
A
B
C
D
G
E
F
H2
H3
A. Faucet Body
B. Base O-Ring
C. Rubber O-Washer
D. Metal U-Washer
E. Mounting Screws
F. Mounting Nuts
G. Hot & Cold Waterlines
H. Aerator Assembly
H1.Aerator Washer
H2.Aerator
H3.Aerator Cover

4
Faucet Dimensions
mm
mm
mm

5
Lift Rod Drain Dimensions
Lift Rod Drain Diagram and Parts List
a
b
c
d
e
f
g
ijkl m
n
o
p
h
a
b
c
d
e
f
g
ijkl m
n
o
p
h
a. Waste Stopper
b. Drain
c. Rubber Washer
d. Concave Washer
e. Plastic Washer
f. Mounting Nut
g. Tailpipe Washer
h. Tailpipe
i. Top Hat Washer
j. Drain Off Pole
k. Washer
l. Retaining Nut
m. Extender Rod
n. Clip
o. Thumb Screw
p. Lift Pole

6
Step 1: Install mounting hardware and waterlines
Remove faucet, mounting
hardware, and waterlines from the
box. Remove mounting nuts (F)
from mounting screws (E). Place
faucet body (A) on a soft cloth,
spout facing up. Secure hot & cold
waterlines (G) at the base of the
faucet (HAND-TIGHTEN ONLY)
A. Hot Side: Left
B. Cold Side: Right
Thread mounting screws (E)
into faucet base, at head up,
and tighten with a Phillips head
screwdriver until snug. Place base
O-ring (B) in groove at base of
faucet
Step 2: Install faucet
Install faucet body (A) through
1-3/8” hole in countertop or
sink, with hot & cold waterlines
(G) and mounting screws (E)
attached
G
GE
A
A
C
B
G
E
E
D
F
F
GE
A
G
GE
A
A
C
B
G
E
E
D
F
F
GE
A

7
Step 3: Secure faucet
Install rubber O-washer (C)
and metal U-washer (D), over
waterlines (G) and mounting
screws (F), from underneath
the countertop or sink. Attach
mounting nuts (F) to mounting
screws (E) and tighten with
adjustable wrench or 10mm
wrench until snug
Step 4: Connect waterlines to main valve
Thread hot & cold waterlines (G)
onto angle stops and tighten with
adjustable wrench until snug. Turn
on angle stops and check for leaks
(DO NOT TURN ON FAUCET)
G
GE
A
A
C
B
G
E
E
D
F
F
GE
A
G
GE
A
A
C
B
G
E
E
D
F
F
GE
A

8
Step 5: Install Drain
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
• Remove waste stopper (a) from
drain (b). Remove tail pipe (h),
mounting nut (f), plastic washer
(e), and concave washer (d) from
drain (b). Remove retaining nut (l)
and washer (k) from tailpipe (h)
• Install drain (b), with rubber
washer (c) attached, into the drain
hole. Attach concave washer (d)
with narrow end up, plastic washer
(e), and mounting nut (f) to drain
(b) from underneath countertop or
sink. Secure tightly to sink with an
adjustable wrench
• Thread tailpipe (h) onto drain (b)
and hand-tighten. Adjust tailpipe
(h) so drain o pole opening is to
the rear of the sink
Installer tip: Leave top hat
washer (g) in tailpipe (h)
Installer Tip: Make sure
tailpipe washer (g) is installed
in tailpipe (h)

9
Step 5: Install Drain
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
a
b
c
d
e
f
g
po
o
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
a
b
c
d
e
f
g
po
o
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jkl
j
• Insert waste stopper (a) into
drain (b). Make sure slot at end
of waste stopper (a) is facing the
rear of the sink
• Insert lift pole rod (p) through the
hole in the back of the faucet body.
Loosen thumb screw (o) and attach
extender rod (m) to lift pole rod (p).
Tighten thumb screw (o)
• Insert shortest end of drain o
pole (j) into drain o pole opening
of tailpipe (h). Make sure drain o
pole (j) and slot on waste stopper
(a) engage. Attach washer (k) and
retaining nut (l) through drain o
pole (j). Secure retaining nut (l) to
drain o pole opening of tailpipe (h)