Kraus Seda FUS1821CH User manual

Seda™ Single Lever Basin Faucet
FUS-1821
INSTALLATION GUIDE
www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV. October 25, 2017

2
Congratulations on the purchase of your new
Kraus plumbing xture!
Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance, or have any problems with your product:
Please contact our Customer Service Team
1-800-775-0703 / [e-mail]
Have the model number available, and retain a copy of your receipt
with purchase date for reference.
If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.
DO NOT RETURN TO STORE

3
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
• Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on angle stops to ush any debris prior to
installing new plumbing. Shut o angle stops
• Pre-drilled hole size requirement: 1 3/8” (min)
• Max countertop thickness: 1 3/8”
Tools you will need:
Adjustable Wrench Phillips Screwdriver Safety Goggles Bucket
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(
∅ 45mm)
∅ 1 15/16”
(
∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(
∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
For technical assistance or replacement parts, please contact Kraus
Customer Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or Customerser[email protected]

4
D
G
B
C1
C2
C3
C4
E
F
A
A. Faucet Body
B. Base O-Ring (factory-installed)
C. Mounting Hardware:
C1. Rubber U-Washer
C2. Metal U-Washer
C3. Mounting Screw
C4. Mounting Nut
D. Hot & Cold Waterlines
E. Adjustable Aerator
F. Aerator Key
G. Hex Wrench
Diagram and Parts List

5
7.2”
183mm
5”
127mm
2.4”
61mm
5.03”
128mm
6.8”
173mm
6”
152mm
1.37”
35 mm
1.37”
35 mm
1.37” MAX
35 mm
Faucet Dimensions

6
a
b
c
d
e
f
g
ijkl m
n
o
p
h
a. Waste Stopper
b. Drain
c. Rubber Washer
d. Concave Washer
e. Plastic Washer
f. Mounting Nut
g. Tailpipe Washer
h. Tailpipe
i. Top Hat Washer
j. Drain Off Pole
k. Washer
l. Retaining Nut
m. Extender Rod
n. Clip
o. Thumb Screw
p. Lift Pole
Lift Rod Drain Diagram and Parts List and Dimensions

7
Step 1: Remove mounting hardware and install waterlines
Remove faucet, mounting
hardware, and waterlines from
the box. Remove mounting nut
(C4) from mounting screw (C3).
Place faucet body (A) on a soft
cloth, spout facing up. Secure
hot & cold waterlines (D) at the
base of the faucet (hand-tighten,
then secure with ¼ turn of
adjustable wrench)
A. Hot Side: Left
B. Cold Side: Right
Thread mounting screw (C3)
into faucet base, at head up,
and tighten with a Phillips head
screwdriver until snug
Step 2: Install faucet
Install faucet body (A) through 1
3/8” hole in countertop or sink,
with base O-ring (B), hot & cold
waterlines (D), and mounting
screw (C3) attached
1 1/4-18UNF-2A
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
C4
C1
C2
C4
C4
A
C3
D
C3
C3
A
C3
DD
E
F
1 1/4-18UNF-2A
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
C4
C1
C2
C4
C4
A
C3
D
C3
C3
A
C3
D
D
E
F

8
Step 3: Secure faucet
Install rubber U-washer (C1)
and metal U-washer (C2) from
underneath the countertop or
sink. Attach mounting nut (C4) to
mounting screw (C3) and tighten
with adjustable wrench or 10mm
wrench until snug
Step 4: Connect waterlines to main valve
Thread hot & cold waterlines (D)
onto angle stops and tighten with
adjustable wrench until snug. Turn
on angle stops and check for leaks
(DO NOT TURN FAUCET ON)
1 1/4-18UNF-2A
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
C4
C1
C2
C4
C4
A
C3
D
C3
C3
A
C3
DD
E
F
1 1/4-18UNF-2A
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
C4
C1
C2
C4
C4
A
C3
D
C3
C3
A
C3
D
D
E
F
Step 5: Install Drain
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
• Remove waste stopper (a) from
drain (b). Remove tail pipe (h),
mounting nut (f), plastic washer
(e), and concave washer (d) from
drain (b). Remove retaining nut (l)
and washer (k) from tailpipe (h)
Installer tip: Leave top hat
washer (g) in tailpipe (h)

9
Step 5: Install Drain
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
• Install drain (b), with rubber
washer (c) attached, into the drain
hole. Attach concave washer (d)
with narrow end up, plastic washer
(e), and mounting nut (f) to drain
(b) from underneath countertop or
sink. Secure tightly to sink with an
adjustable wrench
• Thread tailpipe (h) onto drain (b)
and hand-tighten. Adjust tailpipe
(h) so drain o pole opening is to
the rear of the sink
Installer Tip: Make sure
tailpipe washer (g) is installed
in tailpipe (h)
a
b
c
d
e
f
g
poo
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
• Insert waste stopper (a) into
drain (b). Make sure slot at end
of waste stopper (a) is facing the
rear of the sink

10
Step 5: Install Drain
a
b
c
d
e
f
g
po
o
nn
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jklj
a
b
c
d
e
f
g
po
o
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jkl
j
• Insert lift pole rod (p) through the
hole in the back of the faucet body.
Loosen thumb screw (o) and attach
extender rod (m) to lift pole rod (p).
Tighten thumb screw (o)
• Insert shortest end of drain o
pole (j) into drain o pole opening
of tailpipe (h). Make sure drain o
pole (j) and slot on waste stopper
(a) engage. Attach washer (k) and
retaining nut (l) through drain o
pole (j). Secure retaining nut (l) to
drain o pole opening of tailpipe (h)
• Place one end of clip (n) on drain
o pole (j). Insert drain o pole (j)
through desired hole of extender
rod (m). Place other end of clip (n)
on drain o pole (j)
Installer Tip: You may adjust the
extender rod (m) to a desired
height
a
b
c
d
e
f
g
poo
n
n
m
l
p
m
d
g
b
h
a
b
b
c
e
f
h
ikl
o
p
H1
H2
H3
jkl
j