KTI Networks KC-10FM/T User manual

Specifications
Standard
IEEE 802.3 10BASE-T, 10BASE-FL
10BASE-TRJ-45Connector
One RJ-45 switch is provided for selecting the type of RJ-
45 connector as follows:
RJ-45 Switch RJ-45 Type
X position MDI-X
II position MDI
RJ-45 Pin MDI-X type MDI type
1 Rx+ Tx+
2 RX- Tx-
3 Tx+ Rx+
6 Tx- Rx-
It allows you to make all UTP connections using common
straight-through UTP.
10BASE-TUTPCable
Cable type: Category 3, 4 or 5
Maximum cable distance: 100 meters (328 feet)
FiberOptic Connectors
Two connectors are provided for fiber optic cable connec-
tion. One is labeled "Tx" for transmitting operation. The
other is labeled "Rx" for receiving operation.
Model KC-10FM/T KC-10FM/C KC-10FM/S
Wavelength 850nm 850nm 1300nm
Fiber mode Multimode Multimode Single mode
Connector ST type SC type ST type
Fiber cable*162.5/125 62.5/125 8/125
Cable length 2000 meters 2000 meters 14K meters
Fiber cable*1: Recommended fiber cable
LEDs
Unit LED Power
Port LEDs UTP Link, UTP Rx, Fiber Link, Fiber Rx
(Rx: receiving status)
Environment
Temperature 0o- 40oC
Humidity 10-90% non condensing
Dimension
74mmx51mmx 20mm
Power
+12V / 500mA minimum
DC plug type:
Installation
1. Install the media converter with the DC power adapter
provided. ( +12VDC, 500mA)
2. Connect the power adapter cable to the media con-
verter before connecting the adapter to the AC outlet.
3. Do not connect more than two media converters in
series.
GeneralDescription
The KC-10FM Ethernet media converter is designed to be
a connection interface between a 10BASE-T Ethernet UTP
cable and 10BASE-FL fiber cable with no increasing on the
hop count in the network. Each features a RJ-45 connector
and a pair of fiber optic connectors.
KC-10FM/T UTP to multimode fiber with ST connectors
KC-10FM/C UTP to multimode fiber with SC connectors
KC-10FM/S UTP to single mode fiber with ST connectors
InstallationGuide
Ethernet Media Converters
KC-10FM/T
KC-10FM/C
KC-10FM/S
DOC. 980825-KC10FM-K Rev.2
P/N: 750-0111-001

MakingNetworkConnections
The following example illustrates a connection from a
10BASE-T port of one hub to a 10BASE-FL port of another
hub through a media converter.
The following example illustrates a connection from a
10BASE-T port of one hub to a 10BASE-T NIC on a
computer through a media converter.
InterpretingLEDIndicators
LED Status State Interpretation
Power Power status On Converter is on.
Off Converter is off.
Link Fiber link On The fiber link is ok.
Off No link or the link is faulty.
Rx Receiving status Blink Receiving is in operation.
Off No fiber receiving.
Link UTP link On The UTP link is ok.
Off No link or the link is faulty.
Rx Receiving status Blink Receiving is in operation.
Off No fiber receiving.
The information contained in this document is subject to change
without prior notice.
Copyright Ó KTI. All Rights Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
WARNING:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
tion against harmful interference when the equipment is
operated in a commercial environment. This equipment gener-
ates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instruction manual
may cause harmful interference in which case the user will be
required to correct the interference at his own expense.
NOTICE:
(1) The changes or modifications not expressively approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
(2) Shielded interface cables and AC power cord, if any, must
be used in order to comply with the emission limits.
CISPR A COMPLIANCE:
This device complies with EMC directive of the European
Community and meets or exceeds the following technical
standard.
EN 55022 - Limits and Methods of Measurement of Radio
Interference Characteristics of Information Technology Equip-
ment. This device complies with CISPR Class A.
WARNING: This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
CE NOTICE
Marking by the symbol CE indicates compliance of this equipment
to the EMC directive of the European Community. Such marking is
indicative that this equipment meets or exceeds the following
technical standards:
EN 55022: Limits and Methods of Measurement of Radio
Interference characteristics of Information Technology Equip-
ment.
EN 50082/1:Generic Immunity Standard -Part 1: Domestic
Commercial and Light Industry.
EN 60555-2: Disturbances in supply systems caused by
household appliances and similar electrical equipment - Part 2:
Harmonics.