KTI Networks KGC-300 Series User manual

General
The 1000BASE-T to 1000BASE-SX/LX media converter se-
ries provides 1000Mbps Gigabit Ethernet copper-to-fiber me-
dia conversion, allowing for 1000Base-T-1000Base-X over
multimode or optional single-mode fiber optical media.
Features
• Gigabit copper to fiber conversion: 1000Base-T-to-
1000Base-SX/LX over multimode or single-mode fiber
• SFP design : For flexibility, an SFP (Mini-GBIC) connector
is provided for the fiber port to accommodate any type of
SFP fiber transceiver when needed.
• Support full wire speed copper to fiber conversion
• Auto MDI/MDI-X detection function on the copper port
• Auto-negotiation support
• Plug and play : no configuration settings is required
• Link Fault Pass Through : this function allows link fault
status passes through between copper link and fiber link
transparently.
• Far End Fault function on fiber port
• Transparent conversion to any type of packet frame
• No packet length limitation
• Diversified mounting support : desktop mounting, wall
mounting, optional Din-Rail support
• Center chassis installation : support installation in an cen-
ter chassis rack with benefits of central software manage-
ment and redundant power backup.
• Supportwiderange of fiberoptions:multimode fiber, single
mode fiber (short reach up to long reach), Bi-directional
single fiber, and CWDM optical
• Low power consumption
Specifications
Twisted-Pair Interface (Copper Port)
Connector Shielded RJ-45
Signal Compliance IEEE 802.3ab 1000BASE-T std.
Pin Assignments Auto MDI/MDI-X detection
Data Speed 1000Mbps
Configuration Auto-negotiation support
Cable Types Category 5 or higher UTP
Link Distance Up to 100 meters
Fiber Optic Interface (Fiber Port)
Signal Compliance IEEE 802.3z 1000BASE-SX/LX std.
Connector SFP for pluggable fiber transceiver
Data Speed 1000Mbps, full duplex
Cable Types MMF - 50/125, 62.5/125 µm
SMF - 9/125 µm
Link Distance MMF up to 500m
SMF -model dependent
Eye Safety compliance IEC825 Class 1
Center Interface
Interface For center chassis mounting
Connector FutureBus
DC Power Input
Interface DC Jack (-D6.3mm/+D2.0mm)
Operating Voltages DC input +4.75V ~ +12.6V
Power consumption max 2W @+7.5VDC input
Mechanical
Dimension (base) W 108mm x D 72.5mm x H 23mm
Housing Enclosed metal with no fan
Weight 205g
LED Indicators
PWR ON Power on
OFF Power off
SFP ON SFP transceiver is installed.
OFF No SFP transceiver is installed.
LINK ON Copper-fiber link up
OFF Copper-fiber link down
BLINK Copper-fiber link with data traffic
OL ON Fiber port optical signal detected
OFF Fiber port no optical signal
Environmental
Operating Temperature -5~ 55oC
Storage Temperature -40~ 85oC
Relative Humidity 5% ~ 90%
Approval
FCC Part 15 Class B
CE / CISPR 22 Class B
IEC60950 Safety
Refer to Model Optical Specification sheet for model de-
tails. The documentation describes the detailed fiber configu-
ration, rated operating temperature, and optical specification
of each model.
12
43
Gigabit Ethernet Media Converters
1000BASE-T TO 1000BASE-SX/LX
KGC-300 Series
Installation Guide
DOC.060227-KGC300

Desktop Mounting
The device can be mounted on a desktop or shelf. Make sure
that there is proper heat dissipation from and adequate venti-
lation around the device. Do not place heavy objects on the
device.
Wall Mounting
The device provides a mounting hole on the bottom case as
shown in the figure. Use the hole for a wall mounting.
Applying Power
Beforeyoubegin the installation, check the AC voltage ofyour
area. The AC power adapter which is used to supply the DC
power for the device should have the AC voltage matching
the commercial power voltage in your area. Use one of the
following rated AC-DC power adapters for your installation.
AC120V/60Hz DC7.5V/1A AC230V/50Hz DC7.5V/1A
AC100V/50-60Hz DC7.5V/1A AC100V/50-60Hz DC5V/1A
AC240V/50Hz DC7.5V/1A
Typical Application
Use two media converters connected with an appropriate fi-
ber cable to extend the connection distance between two Gi-
gabit copper devices as shown below:
Connecting to a Fiber Gigabit Ethernet Port
The converter can also connect to a remote fiber Gigabit Eth-
ernet port over a fiber cable. It extends the connection dis-
tance between a copper port and a fiber port as shown below:
56
8
7
DIN-Rail Mounting
ForaDin-Railchassis, the media convertercansupportmount-
ing on a Din-Rail. An optional Din-Rail bracket, KC-3DR can
be purchased separately. Consult your dealer for details. The
following figures show an example after bracket installation:
Center Chassis Installation
The media converter can also be installed in KC-1300 center
chassis. The center chassis provides the power supply to the
converter also with optional power redundancy. Up to 16 units
canbeinstalledinonechassis.Unscrew and remove the cover
of the center connector before inserting the converter into the
chassis. Refer to the operation manual of center chassis KC-
1300 for more information.
FCC NOTICE
This device complies with Part 15 Class B the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This de-
vice must accept any interference received, including the in-
terference that may cause undesired operation.
CE NOTICE
Markingbythesymbol indicatescomplianceofthisequip-
ment to the EMC directive of the European Community. Such
marking is indicative that this equipment meets or exceeds
the following technical standards:
EMC Class B
EN61000-6-3 IEC61000-6-1
EN55022 CISPR22
EN61000-3-2 IEC61000-3-2
EN61000-3-3 IEC61000-3-3
EN61000-6-1 IEC61000-6-1
EN55024 CISPR24
EN61000-4-2 IEC 61000-4-2
EN61000-4-3 IEC 61000-4-3
EN61000-4-4 IEC 61000-4-4
EN61000-4-5 IEC 61000-4-5
EN61000-4-6 IEC 61000-4-6
EN61000-4-8 IEC 61000-4-8
EN61000-4-11 IEC 61000-4-11
The information contained in this document is subject to
changewithoutpriornotice.Copyright(C)AllRights Reserved.
Trademarks
Ethernet is a registered trademark of Xerox Corp.

Model Definition
Model FiberCon. Fiber Distance (Typ.)
300 Free SFP no SFP transceiver
300-SX LC Duplex MMF 500m
300-ESX LC Duplex MMF 500m
300-LX LC Duplex MMF 550m, SMF 10km
300-ELX LC Duplex MMF 550m, SMF 10km
300-LX20 LC Duplex SMF 20km
300-LX30 LC Duplex SMF 30km
300-LX50 LC Duplex SMF 50km
300-LX70 LC Duplex SMF 70km
Bi-directional WDM over single SMF
300-W3510 LC Simplex SMF 10km
300-W5310 LC Simplex SMF 10km
300-W3520 LC Simplex SMF 20km
300-W5320 LC Simplex SMF 20km
300-W3410 LC Simplex SMF 10km
300-W4310 LC Simplex SMF 10km
300-W3410S SC Simplex SMF 10km
300-W4310S SC Simplex SMF 10km
All models listed below except Model 300 are shipped
with a pre-installed SFP fiber transceiver.
Gigabit Ethernet
1000BASE-T TO 1000BASE-SX/LX
MEDIA CONVERTERS
KGC-300 Series
Model Optical Specifications
DOC.060227-KGC300
Rated Operating Temperature
Model Operating Temperature
300-SX -5 ~ +55oC
300-LX -5 ~ +55oC
300-LX20 -5 ~ +55oC
300-LX30 -5 ~ +55oC
300-LX50 -5 ~ +55oC
300-LX70 -5 ~ +55oC
300-W3510 -5 ~ +55oC
300-W5310 -5 ~ +55oC
300-W3520 -5 ~ +55oC
300-W5320 -5 ~ +55oC
300-W3410 -5 ~ +55oC
300-W4310 -5 ~ +55oC
300-W3410S -5 ~ +55oC
300-W4310S -5 ~ +55oC
Extended operating temperature range
300-ESX -10 ~ +70oC
300-ELX -10 ~ +70oC
Optical Specifications
Model Wavelength Tx Power*1Rx Sen.*2Max.Rx*3
300-SX 850nm -9.5~ -4 -18 -1
300-ESX 850nm -9.5~ -4 -18 -1
300-LX 1310nm -9.5~ -3 -20 -3
300-ELX 1310nm -9.5~ -3 -20 -3
300-LX20 1310nm -7~ 0 -24 -3
300-LX30 1310nm -4~ +3 -23 -3
300-LX50 1550nm -4~ +1 -23 -3
300-LX70 1550nm 0~ +5 -23 -3
Bi-Direction WDM over single SMF
300-W3510 T1310/R1550 -9~ -3 -21 -3
300-W5310 T1550/R1310 -9~ -3 -21 -3
300-W3520 T1310/R1550 -8~ -3 -23 -3
300-W5320 T1550/R1310 -8~ -3 -23 -3
300-W3410 T1310/R1550 -9~ -3 -20 -3
300-W4310 T1550/R1310 -9~ -3 -20 -3
300-W3410S T1310/R1550 -9~ -3 -20 -3
300-W4310S T1550/R1310 -9~ -3 -20 -3
*1Tx Power : Transmitter power (min. ~ max., unit: dBm)
*2Rx Sen. : Receiver sensitivity (unit :dBm)
*3Max.Rx. : Maximal Received power (unit : dBm)