KTI Networks KC-220FF-TSA User manual

Specifications
 Complies with IEEE 802.3u 100BASE -FX std.
 Oper tes with connected devices running on full duplex
or h lf duplex mode
 Environment: Temper ture 0 - 40oC
Humidity 10-90% non condensing
 Dimensions: 101mm x 96mm x 25mm
 Power: +12V / 800mA minimum
 DC plug type:
Connectors & Cables
The converter provides one multimode (MM) fiber port
nd one single mode (SM) fiber port s shown below:
The multimode fiber port is used for duplex multimode
fiber c ble connection nd single mode fiber port is used
for duplex single mode fiber c ble connection.
Both ports re compli nt to IEEE 802.3u 100BASE-FX
st nd rd nd c n convert multimode optic sign l to single
mode optic sign l up to b ndwidth 200Mbps tr nsp r-
ently with minim l del y time.
The w velength used is 1300nm for both ports. The
recommended MM (Multimode fiber) c ble is 62.5/125mm
nd SM (Single Mode fiber) c ble is 9/125mm.
General Description
The KC-220FF F st Ethernet medi converter series re de-
signed to convert 100BASE-FX multimode fiber sign l to
single mode fiber sign l. It is used to extend the connection
dist nce between two F st Ethernet fiber optic devices vi
single mode fiber c ble tr nsp rently with no perform nce
degr d tion. The converter series provide different types of
fiber connectors such s ST, SC, nd MT-RJ for MM (multi-
mode) or SM (single mode) fiber c bles.
The outline of the converter is:
Installation Guide
100BASE-FX Multimode-Single mode
Media Converter
KC-220FFSERIES
DOC. 010430-KC220FF-K Rev.1.0
P/N: 750-0155-001
The series provides different types of fiber connectors for
different pplic tions. The connectors include ST, SC, nd
MT-RJ. The following figure illustr tes the v il ble
combin tions:
The following t ble lists the fiber connectors, fiber c bles
nd the m ximum length supported by e ch converter
model:
Model MM Port* SM Port SM Cable Length*
KC-220FF-TSA ST SC 15Km
KC-220FF-TS3 ST SC 30Km
KC-220FF-TS5 ST SC 50Km
KC-220FF-CSA SC SC 15Km
KC-220FF-CS3 SC SC 30Km
KC-220FF-CS5 SC SC 50Km
KC-220FF-CJ SC MT-RJ 15Km
KC-220FF-JJ MT-RJ MT-RJ 15Km
KC-220FF-JSA MT-RJ SC 15Km
* MM Port : the maximum MM cable length is 2K meters.
* SM Cable length : the maximum length in point-to-point full
duplex operation

The information contained in this document is subject to change
without prior notice.
Copyright+ KTI. All Rights Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
WARNING:
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protec-
tion against harmful interference when the equipment is
operated in a commercial environment. This equipment gener-
ates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instruction manual
may cause harmful interference in which case the user will be
required to correct the interference at his own expense.
NOTICE:
(1) The changes or modifications not expressively approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
(2) Shielded interface cables and AC power cord, if any, must
be used in order to comply with the emission limits.
CISPR A COMPLIANCE:
This device complies with EMC directive of the European
Community and meets or exceeds the following technical
standard.
EN 55022 - Limits and Methods of Measurement of Radio
Interference Characteristics of Information Technology Equip-
ment. This device complies with CISPR Class A.
WARNING: This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
CE NOTICE
Marking by the symbol indicates compliance of this
equipment to the EMC directive of the European Community. Such
marking is indicative that this equipment meets or exceeds the
following technical standards:
EN 55022: Limits and Methods of Measurement of Radio
Interference characteristics of Information Technology Equip-
ment.
EN 50082/1:Generic Immunity Standard -Part 1: Domestic
Commercial and Light Industry.
EN 60555-2: Disturbances in supply systems caused by
household appliances and similar electrical equipment - Part 2:
Harmonics.
Installation
1. Inst ll the medi converter with the DC power d pter
provided. ( +12VDC, 800mA)
2. Connect the power d pter c ble to the medi con-
verter before connecting the d pter to the AC outlet.
Making Network Connections
The converters serve s conversion p th between two
F st Ethernet Multimode fiber devices. To both devices,
the conversion is tr nsp rent.
Important rule: When connection is est blished, m ke
sure the devices loc ted t both ends of the p th re
configured nd oper ted using the s me duplex mode nd
the m ximum dist nce must comply with IEEE 802.3u
specific tions.
Interpreting LED Indicators
LED Status State Interpretation
POWER Power status On Converter is on.
Off Converter is off.
MM MM portlink On The MM fiber link is ok.
Off No link or the link is faulty.
SM SM portlink On The SM fiber link is ok.
Off No link or the link is faulty.