KVH Industries TracVision R5SL User manual

TracVision Serial Number
Congratulations! You have purchased the most reliable
satellite TV antenna system available today. Refer to
this guide for basic operation and troubleshooting
information. For installation information, refer to the
Installation Guide.
Welcome!
R5SL, In-motion
R4SL, Stationary (use only when parked)
TracVision Antenna
Switchplate
Data/Power
RF1
RF2
(Optional)
TV 1
TV 2
Receiver 2 Receiver 1
MAINTENANCE
15 VDC
Power
Supply
Vehicle
AC Power
Grounding
Block Vehicle
AC Ground
©2008, KVH Industries, Inc. KVH and TracVision are registered trademarks of KVH Industries, Inc.
The unique light-colored dome with dark contrasting base is a registered trademark of KVH Industries, Inc.
DIRECTV is a registered trademark of DIRECTV, Inc.
DISH Network is an official trademark of Echostar Communications Corporation.
ExpressVu is a property of Bell ExpressVu, a wholly owned subsidiary of Bell Satellite Services.
All other trademarks are property of their respective companies.
Basic Operation Switching Satellites
HD
DIRECTV
DIRECTV
ON
POWERTVINPUT
FORMAT PWR
GUIDE
EXIT
LIST
ACTIVE
BACK
MENU
INFO
OFF
&TV
RC32
AV1AV2 TV
CHAN
PAGE
VOL
PREV
ENTER
123
456
789
0
abc def
ghi jkl mno
pqrs tuv wxyz
SELECT
R
Your TracVision system automatically switches
satellites as you change channels using your
receiver’s remote control.
Note: Receivers might take up to 30 seconds to
display video when changing channels, switching
satellites, or switching between HD and non-HD
channels.
Troubleshooting
If you are experiencing
any operational problems,
call or visit your local
authorized TracVision
dealer or distributor. You
can find an authorized
technician near you by visiting our website at
www.kvh.com/wheretogetservice.
If you need help finding an authorized technician,
please contact KVH Technical Support:
E-mail: [email protected]
Phone: [phone]
The antenna requires an unobstructed view of
the southern sky to receive satellite TV signals.
Common causes of blockage include trees,
buildings, bridges, and mountains.
Dirt buildup or moisture on the dome can reduce
satellite reception. Clean the exterior of the dome
periodically.
Heavy rain or snow can weaken satellite TV signals.
Reception should improve once the inclement
weather subsides.
Make sure your TV and receiver are both turned on
and set up for the satellite input. Finally, check any
connecting cables to ensure none have come loose.
Receivers can sometimes lock up, preventing the
programming from being displayed on the TV. Turn
off and unplug your receiver. Wait 1 minute, then
plug it back in and turn it on.
The TracVision system tracks one satellite at a time.
Therefore, switching satellites with the primary
receiver might cause televisions connected to other
receivers to display different programming, no
programming, or an error message. Simply select a
channel carried by the new satellite, or switch back
to the original satellite.
DIRECTV
The TracVision system switches
satellites automatically as you
change channels using the
primary receiver’s remote control (the receiver
connected to RF1).
If your TracVision system is equipped with the KVH
Tri-Sat AutoSwitch Kit, any receiver equipped with a
Tri-Sat AutoSwitch can control satellite selection.
DISH Network and ExpressVu
The TracVision system switches
satellites automatically as
you change channels using
the primary receiver’s remote
control (the receiver connected
to RF1).
Note: The receiver might
briefly display an error message while the antenna
changes satellites.
NETWORK
TracVision System Diagram
Product Serial Number
Set the switchplate’s Power switch to the OFF (o)
position.
Periodically wash the exterior of the dome with•
fresh water and mild detergent. Avoid harsh
cleansers or volatile solvents (e.g., acetone).
Do not spray the dome with high-pressure•
water.
If you wish to paint the dome, use only•
non-metallic automotive paint without a primer
coat. Metallic paint will impair reception of
satellite signals.
Park your vehicle in an area with a clear view1.
of the southern sky, away from any trees or tall
buildings.
Turn on your receiver and TV.2.
Set the switchplate’s Power switch to the ON3.
(l) position.
Wait 1 minute for system startup.4.
MAINTENANCE
ON
OFF
Turning On the System
Turning Off the System
Product Care
Single-Receiver Setup
Multiple-Receiver Setup
Can the antenna see the satellite?
Excessive dirt or moisture on dome?
Is it raining heavily?
Is everything turned on & connected?
Have you reset the receiver?
Technical Support
54-0560A
The following receivers have been certified by KVH
for use with your TracVision system.
Service HD Non-HD
DIRECTV* H21-200, H20-600 D12, D11, D10
DISH Network 211, 211k 311
ExpressVu 6100 3100
*Tri-Sat AutoSwitch required for KU-band HDTV.
KA-band HDTV is not currently supported.
Certified Receivers

DIRECTV
Your TracVision system is configured for DIRECTV
service by default. No action is required to receive
DIRECTV service.
DISH 1000
Your TracVision system should have been
configured for DISH 1000 during installation. If you
add a new receiver or install a receiver configured
for home use, proceed to Step 1 below to set up
that receiver for mobile use.
Since DISH 1000 coverage varies by region, you
can enjoy your DISH 1000 subscription nationwide
by adjusting the setup for either the 129 or 61
satellite - whichever best suits your location.
Proceed to Step 1 to adjust your setup.
For detailed satellite coverage information, contact
DISH Network at 1-800-333-DISH.
DISH 500 and ExpressVu
Your TracVision system should have been set up for
your selected satellite service during installation.
However, if you add a new receiver or install a
receiver configured for home use, proceed to
Step 1 below to set up that receiver for mobile use.
Service Setup Service Setup
KVH TracVision R5SL/R4SL
User’s Guide
= DISH 61
Satellite
Recommended
Service Key “A”
When required, this key connects to the DB9
connector located on the front of the switchplate.
Service Key “B”
When required, this key connects to the RJ22
connector located on the rear of the switchplate.
Service Key Usage for DISH Network/ExpressVu
Satellite Service Key A Key B
DISH 1000/129 - -
DISH 1000/61 Connect -
DISH 500 Connect Connect
ExpressVu - Connect
Note: DIRECTV service does not require any service
keys or Check Switch tests.
Verify that the values displayed on your TV1.
match those shown for your selected service
in the following tables. If your values do not
match, repeat Step 2.
DISH 1000/129 Results
Port 1 2 3
Satellite 119 110 129
Trans OK OK OK
Status Reception Verified
Switch SW64
DISH 1000/61 Results
Port 1 2 3
Satellite 119 110 61
Trans OK OK OK
Status Reception Verified
Switch SW64
DISH 500 Results
Input 1 1 2 2
Satellite 119 119 110 110
Polarity Odd Even Odd Even
Status Reception Verified
Switch SW42
ExpressVu Results
Input 1 1 2 2
Satellite 82 82 91 91
Polarity Odd Even Odd Even
Status Reception Verified
Switch SW21
Exit the menu and allow the receiver to2.
download the program guide. Once the guide
has loaded, you can start enjoying satellite TV.
Service Setup
Park your vehicle in a blockage-free area.1.
Ensure the receiver you need to configure is2.
connected to RF1. Then turn on the TV and the
receiver.
Turn on the TracVision system. Wait 1 minute3.
for system startup.
Using the receiver remote, go to the “Point4.
Dish/Signal Strength” screen (press MENU
6,1,1 on most models).
Choose5. Check Switch, then press SELECT.
Choose6. Test, then press SELECT. Wait at least
15 minutes for the procedure to complete.
Repeat Steps 4-6 above to run a second test.7.
All ExpressVu and some DISH Network setups
require connecting one or more of the service keys
supplied with your system. This section (continued
on the next page) explains which keys, if any, your
setup requires.
Note: If your setup requires connecting a Service
Key(s), be sure to connect it before proceeding to
Step 2.
KVH Industries, Inc.
50 Enterprise Center
Middletown, RI 02842-5279
Phone: [phone]
E-mail: [email protected]
Tech Support E-mail: [email protected]
MAINTENANCE
A
A
MAINTENANCE
A
When Setup is Required
Step 1 - Connect the Service Key(s)
Step 2 - Run Two Check Switch Tests
Step 3 - Verify Results
B
B