laguna WBSCH User manual

SCHOOL WORKBENCH
WBSCH MANUAL
LAGUNA TOOLS
2072 Alton Parkway
Irvine, California 92606
Ph: 800.234.1976
www.lagunatools.com © 2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the registered trademarks of Laguna Tools, Inc. All rights reserved.

OPERATION MAUNAL
48” x 48” OAK WORKBENCH (WBSCH)
FEATURES
Solid 1.5” thick table top with 2.5” thick skirt
for extra support, total edge thickness is 4”.
Includes both front and end vises with a
double row of bench dog holes in the table for
each vise.
Large storage ball bearing slides drawer.
Includes ten bench dogs and four wooden
stopper bar.
All wooden components are lacquer painted.
SPECIFICATIONS
TABLE DIMENSIONS: 48” x 48”
VISE DIMENSIONS: 13” x 2” x 3.5”
MAX. VISE TRAVEL: 4”
WEIGHT: 98 KGS

ASSEMBLY INSTRUCTIONS:
(FIG. 1)
Please insert the cap screw (No. A) with washer (No.
B) into the right stand (No. 3). Insert the wood pin at
the center hole.
See (FIG. 1)
(FIG. 2)
Repeat the same steps on the other side of the left
stand.
See (FIG. 2)
(FIG. 3)
Attach the side support (No. 4) to the right stand as
shown and secure with a moon nut (No. E) and hex
nut (No. D). Tighten with the supplied 5mm Allen
Wrench (No. C) and a 14mm wrench as shown.
See (FIG. 3)
(FIG. 4)
Repeat Step 3 with the other side support.

(FIG. 5)
Repeat step 1 with the left stand then attach the left
stand to the front and side support as shown and
secure with a moon nut (No. E) and hex nut (No. D).
Tighten with the supplied 5mm Allen Wrench (No. C)
and a 14mm wrench as shown.
See (FIG. 5)
(FIG. 6)
Disassemble the vise support bracket with a 12
mm wrench.
See (FIG. 6)
(FIG. 7)
From the underside of the table, align the holes on
the vise support bracket (No. M) with the holes on
the side edge of the table (No. 1) and secure using 6
wood screws (No. N) (supplied).
See (FIG. 7)
(FIG. 8)
Repeat the step 6 and step 7 to assembly the other
3 vise support brackets to the table top.
See (FIG. 8)

(FIG. 9)
Insert the nut (No. H) into the table edge.
See (FIG. 9)
(FIG. 10)
Turn the stand assembly up side down and
carefully lower it into the underside of the table as
shown.
See (FIG. 10)
(FIG. 11)
Line up the pre-drilled holes in each end of the stand
with the holes in the mounting blocks secured under
the table. Secure the stand to the table at both ends
with cap screws (No. F) and washer (No. G). Tighten
with the supplier 4mmAllen Wrench.
(FIG. 12)
Insert the screw assembly (No. L) through the
middle hole of a vise black (No. 5) then thread the
screw in the middle hole of the vise support
bracket, on the right side of the workbench.

(FIG. 13)
From under the table, re-install the flat washers and
bolts previously removed as step 6, and tighten with
a 12mm wrench.
(FIG. 14)
Place a straightedge on the table and vise face.
Manually adjust the vise face, so it is leveled with
the table top then firmly tighten the screw (No. L) to
secure the vise face in position. With the vise face
leveled with the table top, secure the screw
assembly to the vise face with 4 wood screws (No.
N).
(FIG. 15)
Remove the end cap of handle (No. Q) from both
ends of one vise handle (No. Q) then insert the
handle through handle holder as shown and glue
the caps back on the handle using the supplied
glue tube.
Repeat steps 12 to step 15 with the second screw
assembly on the front edge of the workbench.

EXPLODED DIAGRAM:

PART LIST:
NO. DESCRIPTION SPECIFICATION Q’TY
A Cap Screw M8 x 120mm 8
B Washer Ø8-Ø19mm 8
C Allen Wrench 5mm 1
D Hex Nut M8 x 14 x 6mm 8
E Moon Nut 30 x 15 x 8mm 8
F Cap Screw M6 x 70mm 4
G Washer Ø6-Ø19mm 4
H Nut Ø9 x 13mm 4
I Allen Wrench 4mm 1
J Wood Pin Ø10 x 40mm 4
K Glue 1
L Vise 4
M Vise Support Bracket 180 x 110 x 43mm 4
N Flat Head Wood Screw M4 x 25mm 40
O Stopper Bar 380 x 75 x 50mm 4
P Stopper 28.5 x 45mm 10
Q Handle Ø15.5 x 264mm 4
1 Table Top 1220 x 1220 x 38mm 1
2 Left Support Leg 1210 x 762 x 70mm 1
3 Right Support Leg 1210 x 762 x 70mm 1
4 Side Support 1070 x 135 x 25mm 2
5 Vise Block 380 x 90 x 50mm 4

Laguna Tools is not responsible for errors or omissions.
Specifications subject to change. Machines may be shown with optional accessories.
© 2018, Laguna Tools, Inc. LAGUNA® and the LAGUNA Logo® are the
registered trademarks of Laguna Tools, Inc. All rights reserved.
2072 Alton Parkway. Irvine, CA 92606
Ph: 800.234.1976 | www.lagunatools.com