Lancaster 164WAITRS5BK User manual

(1) /1PC (2) /1PC
(3) /1PC
(7) /1PC(6)/4PC (8) /1PC
SIZE: 31in x 22in
PART LIST:
HARDWARE LIST:
Cam Lock
Screw (26PCS)
Small Cam
Lock (2PCS)
Screws
(12PCS)
ASSEMBLY INSTRUCTIONS
ITEM NO. 30197
(5) /1PC
(9) /1PC (10) /1PC (11) /1PC
Shelf Pin
(6PCS)
Machine
Screw (2PCS)
ADEXA DIRECT LIMITED
TOOLS
REQUIRED:
Phillip’s Head
Screwdriver
(not included)
SIZE: 31in x 22in
SIZE: 24in x 23in SIZE: 24n x 3in
SIZE: 36in x 24in
SIZE: 2in x 3in x 19in SIZE: 22in x 22in SIZE: 20in x 12in
SIZE: 12in x 4in SIZE: 12in x 4in SIZE: 24in x 4in
(A) (B) (C) (D) (E)
Left Side Board Right Side Board
Top Board Kick Board
Back Board
Rack Holders Bottom Board Shelf Bottom
Right Drawer Side Left Drawer Side Front Drawer Side
(4) /1PC
(12) /1PC
SIZE: 20in x 4in
Back Drawer Side
Cam Lock
(26PCS)
(F)
Drawer
Track (1PC)
(G)
Handle
(1PC)
(H)
164WAITRS5BK
164WAITRS5WL.

ITEM NO. : 30197
STEP 1.
Screw Cam Lock Screws (Ax16) onto side boards (1) & (2) and top board (3) and back board (5).
a. Attach tracks onto predrilled holes on side 1 and 2 using the pilot holes to guide you.
A
A
A=2PCS
A=2PCS
(1)
(2)
STEP 2.
Insert cam lock (Fx12) into top board (3), side boards (1 &2). Arrow on cam lock
should face outer edge where screw will be inserted.
(1) (2)
F
FF F
F
F=5PCS
F
F
F
FF
A
(5)
A=8PCS
A=4PCS
A
A
A
A
(3)
A
A
A
AA
A
A
A
F=5PCS
(5) (3)
A=6PCS
(G)
(G)
2a. Insert cam lock screws (Ax12) into back board (5) and top board (3)
A
A
A
AA
A
A
A
AA
A
AAA
A=6PCS

ITEM NO. : 30197
STEP 3.
1. Lay top Board (3) on ground. Add sideboards (1 &2): line up cam lock screw (Ax4) and cam lock (Fx4).
Tighten cam lock (Fx4) with screwdriver once boards are in place.
2. Align bottom board (7) with remaining cam lock screws(A). Tighten cam locks with screwdriver.
BEFORE ASSEMBLE
TIGHTEN ALL THE A
SCREWS AFTER THEY ARE
INERTED INTO THE BOARD
A
STEP 4.
1. Rotate the rectangle made in step 3 so that right side
side (1) is touching the ground. Then place back
board (5) onto the back side of the rectangular
piece. Align the cam lock screws (Ax8) in the
corresponding holes. Tighten the cam lock (Fx5)
with screwdriver.
2. Place 2 small cam lock screws (bx2) in the predrilled
holes on the underside of bottom board (7).
STEP 5.
Align 2 screws (B) on bottom board (7)
with holes on kickboard (4), press
kickboard onto screws.
(5)
B
(4)
(1)
(2)
(3)
(7)
A

STEP 6.
STEP 7.
1. Place 4 cam locks (F x4) into back drawer (12) and Place 4 cam lock screws into front drawer (11)
2. Place 2 cam locks and 2 cam lock screws into 9 and 10.
(9)
(10)
(12)
(11)
(8)
C
A
A
F
E
(13)
ITEM NO. : 30197
D
(6)
Use Shelf pins (D) to place stainless
steel rack holders (6x4) at desired height.