Lancaster 30195 User manual

(1) /1PC (2) /1PC
(3) /1PC
(7) /1PC(6)/1PC (8) /1PC
SIZE: 31in x 22in
PART LIST:
HARDWARE LIST:
Cam Lock
Screw (46PCS)
Small Cam
Lock (4PCS)
Screws
(12PCS)
ASSEMBLY INSTRUCTIONS
ITEM NO. 30195
(5) /1PC
(9) /1PC (10) /1PC (11) /1PC
Shelf Pin
(46PCS)
Machine
Screw (2PCS)
ADEXA DIRECT LIMITED
TOOLS
REQUIRED:
Phillip’s Head
Screwdriver
(not included)
SIZE: 31in x 22in
SIZE: 36in x 23in SIZE: 36in x 3in
SIZE: 36in x 36in
SIZE: 35in x 22in SIZE: 35in x 22in SIZE: 33in x 12in
SIZE: 12in x 4in SIZE: 12in x 4in SIZE: 36in x 4in
(A) (B) (C) (D) (E)
Left Side Board Right Side Board
Top Board Kick Board
Back Board
Shelf Bottom Board Drawer Bottom
Right Drawer Side Left Drawer Side Front Drawer Side
(4) /1PC
(12) /1PC
SIZE: 32in x 4in
Back Drawer Side
Cam Lock
(26PCS)
(F)
Drawer
Track (1PC)
(G)
Handle
(1PC)
(H)
164WAITRS3WL
164WAITRS3BK.

ITEM NO. : 30195
STEP 1.
Screw Cam Lock Screws (Ax16) onto side boards (1) & (2) and top board (3) and back board (5).
a. Attach tracks onto predrilled holes on side 1 and 2 using the pilot holes to guide you.
A
A
(5)
A=2PCS
A=2PCS
A=8PCS
(1)
(2)
A=4PCS
A
A
A
A
(3)
A
A
A
A A
A
A
A
STEP 2.
Insert cam lock (Fx18) into bottom Board (7), top board (3), side boards (1 &2).
Arrow on cam lock should face outer edge where screw will be inserted.
(1) (2)
(7)
(3)
FF
F
FF F
F
AA
F
F
F
F
FF
F=5PCS
F
F
F
FF
F=2PCS
F=6PCS
F=5PCS
2a. that says insert 2 cam lock screws (Ax2) into piece 7.
(G)
(G)

ITEM NO. : 30195
STEP 3.
1. Lay top Board (3) on ground. Add sideboards (1 &2): line up cam lock screw (Ax4) and cam lock (Fx4).
Tighten cam lock (Fx4) with screwdriver once boards are in place.
2. Align bottom board (7) with remaining cam lock screws(A). Tighten cam locks with screwdriver.
(1)
(2)
(3)
(7)
A
BEFORE ASSEMBLE
TIGHTEN ALL THE A
SCREWS AFTER THEY ARE
INERTED INTO THE BOARD
A
STEP 4.
1. Rotate the rectangle made in step 3 so that right side
side (1) is touching the ground. Then place back
board (5) onto the back side of the rectangular
piece. Align the large cam lock screws (Ax8) in the
corresponding holes. Tighten the cam lock (Fx5)
with screwdriver.
2. Place 2 small cam lock screws (bx2) in the predrilled
holes on the underside of bottom board (7).
)5(
B
STEP 5.
Align 2 screws (B) on bottom board (7)
with holes on kickboard (4), press
kickboard onto screws.
(4)

STEP 6.
1. Place 4 cam locks (F x4) into back drawer (12) and Place 4 cam lock screws into front drawer (11)
2. Place 2 cam locks and 2 cam lock screws into 9 and 10.
FF
FF
A
A
A
A
STEP 7.
Align all 3 panels of outside of drawer (10,12 and 9). Tighten cam locks.
a. Slide bottom of drawer (8) into notches.
b. Put piece (11) on front and tighten cam locks.
c. Attach handle (G) to predrilled holes on the front of board (11) with (Cx2).
d. Attach tracks to the outside of piece 9 and 10
e. Insert drawer into tracks on assembled waitress station
(10)
(9)
(12)
(11)
(8)
C
A
A
F
E
(13)
STEP 8.
1. Insert shelf pins (Dx6) on each side of the waitress
station at desired height. place the shelf (6) on pins.
2. Adjust track to ensure tight fit if needed.
D
(6)
ITEM NO. : 30195
(11) (12)