Landscape Forms Carousel User manual

casualht SUPPORT‘A’
1X–3seat
ASSEMBLEWITHCARE! Pangard IIPolyesterPowdercoat isastrong,long‐lastingfinish.Toprotect
thisfinishduringassembly,placeunwrappedpowdercoated partsonpackagingfoamorothernon‐
marringsurface.Donotplaceorslidepowdercoated partsonconcreteorotherhardortextured
surface– thiswilldamagethefinishcausingrusttooccur.Usetouch‐uppaintonanygougesinthe
finishcausedbyassemblytools.
Toolsrequired:
•protectivepadding
•Phillipsheadscrewdriver
•Non‐corrosiveanchors,maximumØ3/8”[9mm]–3for3‐seatunit,4for4‐seatunit
•9/16”wrench(forseats)
•5/32”hexkey
•7/16”wrench(forumbrellahardware)
WARNING!TABLESMUSTBEFASTENEDSECURELYTOHARDSURFACINGTO
PREVENTTIPPING.
Installation Guide
Carousel casual height table
www.landscapeforms.com Ph: 800.521.2546
Date: June 21, 2018
Page 1 of 2
Includedcomponents:
•Support‘A’withsurfacemounttabs
•Support‘B’withsurfacemounttabs
•Seats(qty andstyledependsonorder)
•1tabletopperunit,withattachinghardware
•(1)¼‐20x2‐1/4”Phillipspanheadmachinescrew
andlocknut
casualht SUPPORT‘B’
1X–3seat
1X–4seat
casualht SUPPORT‘A’
1X–4seat
30”dia tabletop,
MarneauxorCatena
27”squarewood
Tabletop
30”dia wood
Tabletop
30”squareMarneaux
Tabletop
Backless
Gridseat
Backless
perfseat
Backed
gridseat
Backed
perfseat
Hoop
seat
1Xperseat‐ 3/8‐
16x1‐1/2”
indentedhexhead
machinescrew
1Xperseat–
3/8washer
TABLETOPASSEMBLY:SeeFig1andFig2.
Note:DONOTDRAGunitacrossconcreteorotherroughsurfaces.Thiscoulddamage
thepowdercoat onthebottomofthesurfacemounttabs.
1. Verifythatsurfacemounttabsaresecurelyfastenedtosupportlegs.Tightenif
necessary.
2. Placetabletopupsidedownonnon‐marringlevelsurface.
3. Placetablesupport“A”(has5”ringatcenter)upsidedownontabletopandalign
holes.
4. Looselyfastensupporttotabletopwithscrewsprovided.
‐Catena/Steelheadtablesinclude(12)1/4‐20x3/4”Phillipstrussheadtapping
screws
‐Marneaux®includes(4)1/4‐20x3/4”Phillipspanheadmachinescrewsand
washers.
Onescrewrequiredattheouterholeineachplate.
‐Squarewoodtabletopincludes(12)1/4‐20x1”Phillipspanheadmachinescrews.
5. Holdtablesupport“B”upsidedownandcarefullyloweritoversupport“A”sobar
on“B”fitsintonotchon“A”.Looselyfastensupport“B”totabletop.
Theuseofpowerdriversisnotrecommended.Threadsorthreadedinsertsmaybe
damagedorbrokenduetoover‐torqueing.
6. Installhardware.Tightenalltabletopfastenersuntilsnug,thentighten
additional1/4turn.
7. Turntablerightsideupusingatleasttwopeople.
PROCEDUREFORASSEMBLINGSEATS:SeeFig3.
Note:TheseinstructionsapplytoallseatstylesforCarouselunits.SeatswereNOT
designedtoswivel.Allowingtheseattoswivelwilldamagethefinishandtheproduct.
1. Slideseatstemintotubeonsupport.Backlessseatsshouldbeinstalledwiththe
flatpartofthestemfacingintowardthecenterofthetable.
2. Alignthreadedholeinseatstemwithholeinsupporttube.Thismayrequire
liftingtheseatslightly.
3. Insertwasherandhexheadmachinescrewthroughthesupportholeandtighten.
Screwsarecoatedwithadrythreadlockingcompoundthatcuresin24hours.
Wiggleseatsandtightenasnecessaryuntilseatissecurelyfastened.

Installation Guide www.landscapeforms.com Ph: 800.521.2546
Page 2 of 2
Fig.2–InstallsupportB
1/4‐20
SCREW
SUPPORT‘A’
SUPPORT‘B’
Carousel casual height table Date: June 21, 2018
SURFACEMOUNTINSTALLATION:
1. Placeunitindesiredpositionandmarkanchorlocationsthroughholes
providedinsurfacemounttabs.
2. Moveunitanddrillholes.
3. Cleartheholesofdustanddebrisusingcompressedair.
4. Placeunitindesiredpositionandinstallalloftheanchors.Afterallanchors
areinstalled,tightenasrecommendedbyanchormanufacturer.
5. Periodicallycheckfastenersandtightenifrequired.
UMBRELLAASSEMBLY:
1. Toinstallumbrella,slideumbrellapolethroughholeintableandintotubeon
support“B”.
2. Alignholesinbasetubeandumbrellapole.Insertlong1/4‐20machinescrew
andsecurewithlocknut.
CAUTION:Donotletgooftheumbrellauntilthepolehasbeensecured.
WARNING!Allcasualheightunitsmustbeanchored.
Fig.3–Installseat
FLATSIDE
OFSEAT
STEMFACESIN
BACKLESS
GRIDSEAT
SHOWN
MACHINE
SCREW
WASHER
Fig.1–InstallsupportA
1/4‐20SCREW
TIGHTEN
SCREWSIF
LOOSE
SUPPORT‘A’
ATTACHATTHIS
LOCATIONFOR
MARNEAUX
TABLETOPS
TABLETOP
(CATENASHOWN)